Brief:
This is a two-stage scale model o' t' WAC Corporal with Tiny Tim Booster from Aerospace Specialty Products. Ya scallywag! It has a 24mm booster stagin' t' an 18mm sustainer.

Construction:
Tiny Tim Booster Parts consist of:

• 1 Body Tube (BT-55)
• 1 Engine Tube (BT-50)
• 1 Stuffer Tube (BT-20)
• 1 Lower Telescopin' Tube (19mm)
• 1 Upper (Short) Telescopin' Tube (19mm)
• 1 Tube Coupler (BT-20 coupler)
• 3 1/16" Wood Dowels, 2 20/50 Centerin' Rings
• 3 50/55 Centerin' Rings
• 4 1/4" wide Strip Styrene
• 1 1/8" wide Strip Styrene
• 1 Paper Shroud
• 6 Rubber Bands
• 1 Basswood Strip
• 1 Launch Lug
• 3 Pre-Cut Fins

WAC Corporal (Upper Stage) parts consist of:

• 1 18mm motor tube
• 1 18mm Motor Block
• 2 20/50 Centerin' Rings
• 1 50/55 Centerin' Ring
• 1 Stuffer Tube
• 1 BT-55 Body Tube
• 1 Keelhaul®©™Shock Cord
• 1 Elastic Shock Cord
• 1 3/16" Launch Lug
• 1 1/4" Square Balsa Stick
• 1 Balsa Nose Cone
• 1 Screw Eye
• 3 Washer Nose Weights
• 3 Pre-cut Fins
• 1 Balsa Boat tail
• 1 Parachute Kit
• 2 Stagin' Tubes

T' BT-55 tube for t' upper stage had a significant crease in it. Avast, me proud beauty! I'm nay sure where t' damage originated, but I contacted BRS Hobbies, which is where I purchased t' kit, me hearties, me hearties, ya bilge rat, and Brian sent me a replacement tube immediately. BRS Hobbies is a great company t' deal with. Ahoy! Avast! Also, t' booster stage BT-55 tube be uneven on one end. Arrr! Well, blow me down! I had t' trim about 1/8" t' make it even.

T' instructions were well documented with detailed steps and helpful illustrations. There is a checkbox beside each step t' help keep up with what you have done. If you read through them beforehand, you'll see some steps that can be done concurrently. Well, blow me down! Blimey! Ya scallywag! Blimey! There is also good information on how t' use t' necessary adhesives and different options for finishing. Ahoy! Blimey! T' templates and illustrations were excellent except for t' fin marking/alignment guide. T' problem with t' fin markin' guide be t' body tube eclipses t' circle for t' body tube, me hearties, me bucko, so you don't know if it is perfectly aligned with it or not. Begad! Blimey! Instead o' usin' t' provided guide, shiver me timbers, I made me own with t' fin position wrapper and fin alignment guide printed from t' freeware program VCP. T' only other deviation I made was leavin' out t' washer nose weights. Based on t' CP/CG relationship they were nay necessary for stability. Blimey! Blimey! I learned a lot o' new scale modelin' techniques buildin' this rocket. Begad! Blimey! T' styrene strips on t' booster section looked awesome. Avast, me proud beauty! Blimey! T' fins took a bit o' work though but were nay too hard t' shape. Arrr! Blimey! I worked hard t' get them t' way ASP suggested.

Finishing:
I prefinished t' body tubes with 3 coats o' Elmer's Fill 'n' Finish. Aye aye! After shapin' t' fins, me bucko, ya bilge rat, arrr, I coated them with 3 light coats o' yellow wood glue and sandin' lightly betwixt coats. Aye aye! I also did this t' t' balsa nose cone, ya bilge rat, boat tail, me hearties, arrr, and balsa conduit. After t' glue treatment, me hearties, I used 2 coats o' Fill 'n' Finish on t' balsa sections. Begad! I used Krylon primer and paint with a matte finish.

Construction Rating: 5 out o' 5

Flight:
I had some really bad flights with this, ya bilge rat, but none o' it be due t' t' rocket. Avast! T' recommended motors seem appropriate compared t' what I saw and simmed. Avast! Aye aye! Please note, nay t' try t' fly t' upper stage by itself on an A motor. T' recommended minimum is a B4-2. Ya scallywag! I tried it on an A8-5 and it lawndarted before t' ejection occurred. Arrr! Ahoy! For t' first flight, I attempted a 2-stage configuration but forgot t' install t' upper stage motor. Begad! T' booster still pressurized t' upper stage enough t' deploy t' chute while boostin' and t' chute was destroyed. Ya scallywag! When it landed, t' booster suffered a broken fin, shiver me timbers, but I fixed it at t' field. Arrr! I tried again t' same day. Aye aye! Avast! On t' second flight, t' upper stage motor lit but did nay separate. Ya scallywag! Arrr! I think I didn't secure it well enough and it got stuck on t' passport tube. It fried t' entire inside o' t' booster section. Through both flights, me hearties, t' upper stage was nay damaged. Arrr! I repaired t' booster section later and tried again. Arrr! I flew t' upper stage by itself on too small a motor and lawndarted. Begad! T' only damage was t' very tip o' t' nose cone. Ahoy! It looked a little mashed and I trimmed it at t' field. Well, blow me down! I then flew t' 2-stage configuration again. Begad! Arrr! T' stagin' and flight were perfect, but t' field was a little too small and wind a little too strong. I recovered t' booster, shiver me timbers, matey, but t' upper stage drifted off far away. Aye aye! I never found it. Aye aye! I noticed afterwards thar be a big difference in me RockSim weight and t' ASP weight, which probably affected t' differences in estimated altitude. Blimey! Ya scallywag! RockSim was predictin' only 400+ feet but ASP calculated 710'. Ahoy! I think t' rocket was probably a lot lighter than what I had modeled in RockSim. Aye aye! If I had weighed it beforehand and adjusted t' RockSim design, me hearties, I probably would have gotten a more accurate estimation. Avast, me proud beauty! Begad! I should have used a smaller chute and/or waited t' fly it in a bigger field.

Recovery:
T' booster uses tumble recovery and on t' one successful flight, it came in undamaged. Begad! T' upper stage comes with a 12" mylar chute. Avast, me proud beauty! Mine be destroyed on t' first flight when it came out too early. Ya scallywag! Avast! For subsequent flights I used a 12" military silk chute. Begad! Arrr! Seein' as how I lost it, me bucko, I'd say it came down too slow, especially in 10+ mph wind. Begad! In me opinion, t' upper stage is sturdy enough t' come down faster and nay sustain any damage.

Flight Rating: 5 out o' 5

Summary:
I think this is an excellent kit. Aye aye! Arrr! I learned a lot about scale modelin' and stagin' . Ya scallywag! Even though t' flights were all ill-fated, arrr, it was from no fault o' t' rocket. Blimey! Begad! This rocket suffered lots o' abuse and with minor repairs was still flyable. Aye aye! T' durability is one o' t' main PROs o' this kit. It also provides a good education t' those gettin' into scale modelin' and t' learn about direct staging. Ya scallywag! Blimey! I think t' only CON I found be t' alignment guide, which be probably usable I just didn't trust it. Ya scallywag! Begad! This was an awesome rocket, ya bilge rat, and I look forward t' buildin' more kits from ASP in t' future.

Overall Rating: 5 out o' 5