Brief:
Estes mini high performance 2 stage rocket can also be flown single. Well, me hearties, blow me down! Blimey! Blimey! Blimey! It uses mini engines and has a streamer recovery for t' body and tumble for the booster. Ya scallywag! Blimey! Aye aye! Blimey! Blimey! Blimey! It has die-cut fiber fins.

Construction:
1 long body tube, shiver me timbers, 2 short body tubes, 1 tube coupler, matey, ya bilge rat, 1 nose cone insert, arrr, 1 nose cone, ya bilge rat, me hearties, 1 orange streamer, shiver me timbers, 1 shock cord, 1 launch lug, 1 cardboard fin sheet, arrr, me hearties, matey, and 1 decal sheet.

T' instructions are very easy t' follow and contain good illustrations. Avast, me proud beauty! The assembly order seems logical. There were two templates, one for t' bigger body tube and one for t' 2 smaller tubes. Well, blow me down! Begad! It was annoyin' that some directions were on t' back o' t' templates when you had t' cut them out but it was nothing unmanageable. Ya scallywag! Fin alignment wasn't so simple, as I used regular Elmer's glue, which we all know takes years t' dry. Aye aye! So I had t' hold me fins in their places for a while. Avast, me proud beauty! I suggest NOT usin' Elmer's glue even though it gave me a very strong hold when it dried because it takes too long. Begad! Begad! All t' parts fit perfectly and t' rocket seems really durable and sturdy. Avast, me proud beauty! No special tools were needed and no supplies other that t' basics were used.

Finishing:
There are no special requirements for finishing. Avast! Avast! I painted t' upper body tube flat enamel white and t' fin section blue gloss. Well, blow me down! Begad! That be what be shown in the manufacturers picture, but I didn't want me booster section t' be yellow so I painted it gloss red--a patriotic rocket! T' instructions for finishin' are easy. Aye aye! There is one small decal that goes on t' main body tube and a few little Estes decals you can basically put anywhere. Ahoy! It looks okay but I've seen much more attractive rockets in me lifetime.

Construction Rating: 4 out o' 5

Flight:
T' recommended motors are A3-4T (first flight), shiver me timbers, A10-3T, A10-0T Booster. I have not flown mine yet, ya bilge rat, as I have yet t' produce t' funds for a couple packs of motors, arrr, however, shiver me timbers, I have seen one flown with an A10-3T and A10-0T booster. Ahoy! It went incredibly high and didn't go straight at all. Arrr! Arrr! It looked unstable. Well, blow me down! The owner didn't even bother t' look for it, arrr, as it be still in t' thrust stage when it went over t' horizon. Avast! It was projected t' go over 900 ft and I think it went at least 1100 ft when I saw it fly. Avast, me proud beauty!

Recovery:
T' shock cord be typical Estes with paper mount. Blimey! Ya scallywag! T' materials seems t' be very strong and o' high quality. T' recovery is a streamer and I think that since t' rocket is so light it will work fine.

Flight Rating: 3 out o' 5

Summary:
T' best thin' about t' Mini Cobra is that it is a cheap, small, ya bilge rat, shiver me timbers, high performance dual stage rocket. Ahoy! Blimey! It's fairly easy t' build and I would put it more under t' category o' skill level 2 rather than Estes' placement o' skill level III.

Overall Rating: 3 out o' 5