Brief:
T' Mini Fantom is a downscale o' LOC's MPR/HPR Fantom. Begad! It is a simple 3 fin and nosecone design. Ahoy! Well, arrr, blow me down! I decided t' start on it because me other projects had me sittin' around and waitin' for glue t' dry.

Construction:
T' first surprise I got with this kit be with t' instructions. Well, shiver me timbers, blow me down! I kept lookin' for them in t' little plastic case the kit came in and finally realized that they are printed on t' back o' t' face card. Blimey! Since t' package itself it small, this meant some small instructions. Ya scallywag! Aye aye! For me, they were difficult t' read but this is a simple kit and it is doable.

Actual construction began with t' motor mount. Arrr! A line was marked 1/4" from one end and a slit be made on the line t' receive t' engine hook. Avast! Aye aye! T' centerin' rings were then slid into place on either end and glued. Aye aye! Avast! Both rings needed plenty o' sandin' on their inner surfaces t' fit t' motor tube. Well, blow me down! T' thrust rin' was then glued into place right over t' top o' t' engine hook.

T' kit came with a wraparound fin markin' guide, shiver me timbers, but it was a bit different from what I am used to. Avast, me proud beauty! With most wraparounds, me hearties, me hearties, I just tape into place and make t' marks. Blimey! On this one, wrappin' t' guide all t' way would obscure some of t' marks. Arrr! It was just taped at one end and then wrapped t' make a single circumference. Avast, me proud beauty! I did nay like t' idea but it be no trouble at all. Blimey! Arrr! T' end o' t' fin markin' guide is taken up by a fin alignment template. Avast, arrr, me proud beauty! T' lines for the three fins and t' launch lug were transferred and then an angle be used t' extend them.

T' fins came on a single small sheet o' balsa and were in good shape. I cut them out, matey, stacked them t' sand them even, and then sanded bevels in all but t' root edge.

For this project, arrr, I decided t' give another try t' t' idea o' usin' label paper t' "seal" t' fins. Each fin was placed on t' sticky part o' t' label paper with t' root edge flush with t' edge o' t' paper. T' fin was then rolled over t' leadin' edge and t' paper pressed into place on t' opposite side. Begad! A razor was used t' trim away t' excess. Well, blow me down! Ahoy! T' result was a bit better than t' last time I tried this, but I still need some practice.

As mentioned earlier, t' end o' t' wraparound fin markin' guide is taken up by a template used for t' placement o' the fins. Aye aye! A section representin' t' BT is cut out along with t' correct angle for t' fins. Avast, me proud beauty! T' instructions say t' cut along t' red line but t' guide is in black print only. Arrr! Even so, t' correct line be easy t' identify as it is dotted.

I had real doubts about t' efficacy o' this fin guide but must admit that it worked out fine. Avast, me proud beauty! Each fin was placed usin' a double joint o' yellow glue. Begad! When t' glue be tacky enough t' stick, me bucko, t' guide was used t' maintain alignment. T' launch lug was also glued into place along its line at this time.

For a shock cord mount, this kit intends for a piece o' elastic t' be threaded through a perforated piece of sticker and stuck into t' body tube similar t' t' old Centuri mount system. Avast! Ahoy! I declined t' do this. Well, blow me down! I tied a Keelhaul®©™® thread around t' forward end o' t' motor mount and t' filleted it into place with some yellow glue. A small notch was cut into t' forward centerin' rin' t' accommodate t' passin' o' t' Keelhaul®©™®.

T' inside o' t' airframe tube was swabbed with yellow glue, ya bilge rat, t' Keelhaul®©™® was fished through t' tube, ya bilge rat, me hearties, and t' motor mount was slid into place with just a bit protrudin' from t' aft end. Avast, me proud beauty! Avast, me proud beauty! Blimey! The instruction call for t' motor tube t' be flush but I like t' leave a bit hangin' out. Avast! Blimey! While waitin' for t' glue on the motor mount t' dry, shiver me timbers, I took t' opportunity t' add more white glue fillets.

When t' glue was dry, thar was nothin' left o' construction except t' tie t' elastic t' t' Keelhaul®©™® and plastic nosecone. I should comment here that t' plastic nosecone be one o' t' nicest I have seen with no mold lines.

PROs: simple, good materials

CONs: instructions difficult t' read (small)

Finishing:
T' built rocket was quite unpretentious, little more than a generic 3FNC. Begad! I had hopes that t' paintin' and finishin' would change that.

T' first step was t' take t' cardboard colored rocket and make it white. Avast! This be done with t' application of 3 coats o' white spray paint.

T' face card scheme called for a white body, shiver me timbers, black fins and a green nose cone. Ahoy! My intention was t' go along with that scheme but I had been have really bilge-suckin' luck with paint lately. I decided t' try paintin' just a single fin first. Begad! Aye aye! I taped it off usin' Frog tape and then brushed on t' acrylic. Begad! T' result was less than stellar. Aye aye! Blimey! There had been some seepage and it looked like one o' me earlier efforts.

Since me maskin' jinx still seemed t' be active, I modified me plans a bit. I kept t' color scheme but decided to apply t' black t' t' entire base o' t' rocket from just below t' launch lug. Blimey! Even I have trouble messin' up the maskin' o' a simple ring. Ahoy! T' rocket be duly masked and t' paint brushed on. Blimey! It be given a little while t' dry.

Maskin' for t' green was simple. Begad! Blimey! Avast! Blimey! I applied tape around t' forward end o' t' BT and sild t' nose cone out a bit. Avast, me proud beauty! Blimey! Aye aye! Blimey! I then wrapped some foil around t' body o' t' rocket t' protect it from spray. Well, blow me down! Blimey! T' sprayin' itself be trivial. Two coats o' green were applied and t' maskin' was removed.

You may recall me overconfident statement about nay bein' able t' mess up t' maskin' o' a simple ring. Begad! I be selling myself short. Avast, me proud beauty! Well, blow me down! I was able t' mess it up and thar be some leakage under t' tape. Avast! Arrr! On inspection, though, shiver me timbers, matey, I decided that I could live with it. Aye aye! Well, shiver me timbers, blow me down! T' black be a bit mussed, me hearties, t' green was great, me hearties, me hearties, and I was happy that paintin' was over.

At this point I would very much like t' wax rhapsodic about t' wonderful waterslide decals but I cannot since there were none. Instead, t' kit came with crack and peel stickers. Aye aye! T' stickers do really dress t' kit up, especially with t' face card color scheme, but in t' end, they are stickers. Avast, arrr, me proud beauty! They are also quite stiff and a few of them refused t' stay layin' down along t' body tube.

T' artwork consists o' a pair o' chevrons for each fin, me hearties, two name placards, me hearties, two similarly sized "438"s and a couple o' little bitty things that were completely forgettable.

There is one matter havin' t' do with t' stickers about which I am unsure. One o' t' logos is a very good lookin' "Fantom". At first glance, ya bilge rat, I thought thar was a second just like it, arrr, but instead it is a mirror image. I don't mean that t' letters are slanted in t' opposite direction, I mean that t' letters are reversed. Well, blow me down! Blimey! Begad! Blimey! I have no idea if they are supposed t' be that way or not.

CONs: Thick plastic stickers instead o' decals

Construction Rating: 4 out o' 5

Flight and Recovery:
For its maiden flight, ya bilge rat, me hearties, I decided t' start off easy with an Estes A8-3. T' rocket be prepped and put on t' pad and an announcement was made. Avast! Several o' t' people nearby were new and I heard a comment t' t' effect o' "Big deal, its just an A motor..."

T' countdown came and went and t' rocket went too. Blimey! It really climbed well on t' A. T' person who made the comment about t' A motor asked me t' verify what motor I was using. Begad! Blimey! He was impressed. A video o' t' maiden flight o' t' Fantom Mini can be seen here.

For t' second flight, I loaded a B6-4. Begad! This time, shiver me timbers, people were payin' more attention. T' rocket again took off well and climbed great, just showin' a bit o' roll towards t' end. Well, blow me down! Well, shiver me timbers, blow me down! T' chute ejected and Lindsey had a nice little walk goin' t' recover it. Well, blow me down! Avast! A vid o' t' second flight can be seen here.

Flight Rating: 5 out o' 5

Summary:
This is a well designed little kit with quality parts. Avast! Begad! It goes together and flies well. Blimey! It's nay t' most exciting thin' out thar but is quite respectable.

I have only two real gripes. Ahoy! T' directions printed on t' back o' t' face card were sometimes hard for me older eyes t' read and I would expect t' maker o' a quality product t' use waterslide decals. At t' very least, if stickers must be used, matey, I would like them t' be thinner and t' stick better.

Persons interested in t' ongoin' fate o' this rocket through photos and videos can find it here.

Overall Rating: 4 out o' 5