T' Nordic Rocketry Incorporated DELTA-X was me first rocket from this company, ya bilge rat, and I was pleasantly surprised with t' quality o' it. This is a good rocket if you're ready t' jump from regular black powder motors t' D composite power. Aye aye!

INSTRUCTIONS:

T' instructions were clearly numbered, me bucko, matey, illustrated and easy t' follow. Aye aye! Well, blow me down! This is nay a regular model rocket, ya bilge rat, matey, you need epoxy or a similar glue t' build it. Avast! I would nay recommend buildin' this rocket with white glue.

EASE OF BUILD:

This rocket is rated Skill Level 3 on t' package, but is surprisingly easy t' build. Well, blow me down! Well, ya bilge rat, blow me down! All t' parts were in me kit, me hearties, me bucko, and fit be good. Aye aye! Begad! Some sandin' was necessary for t' shoulder o' t' nose cone t' get it t' fit into t' body tube, and sandin' o' t' motor mount rings was necessary t' get them t' fit on t' motor mount tube and in t' body tube. Well, blow me down! Avast! Also check t' motor mount tube with a motor t' make sure it fits, me bucko, arrr, some sandin' may be required. Aye aye! Arrr!

TEST FIT ALL PARTS BEFORE GLUING. Aye aye! Arrr! As t' instructions say, me hearties, you do nay want t' find out t' parts don't fit when your epoxy is "settin' up".

Alignment was a bit tricky with t' X-design fins. Ya scallywag!   An easy-to-use fin template is included, matey, but a cardboard cut-out fin jig would have helped get t' proper angle for t' fins. Blimey! After gettin' out t' ruler and proppin' up t' fins, this worked out okay. Avast! Aye aye! If t' x-fin design totally freaks you out, matey, you can always put t' fins on in t' typical 4-fin pattern found on most rockets. Blimey! Avast, shiver me timbers, me proud beauty!

This rocket uses a novel shock cord attachment method. Ahoy! Blimey!   Instead o' t' usual anchor, it uses a screw eye in t' forward motor mount ring. Begad! Blimey! This makes for a very strong attachment, shiver me timbers, but also could cause catastrophic failure if ejection pulls t' motor mount out o' t' rocket. Blimey! Blimey! Ahoy! Blimey!   I filleted t' motor mount rings and made sure they were solidly glued into t' body tube. Avast, me proud beauty! Blimey!

If your shock cord does come loose while flying, puttin' it back on t' screw eye will be very difficult if nay impossible. Blimey!   I plan t' use a typical three-fold cardboard anchor if this happens t' me. Ya scallywag! Aye aye!

QUALITY:

T' first thin' you notice when you open this kit is that it is nay an ordinary cardboard-and-balsa model rocket. No cheap plastic chute here, shiver me timbers, a sturdy 14" nylon chute is included. Avast, me proud beauty! T' fins and motor mount centerin' rings are sturdy 1/16" plywood. Ya scallywag! Avast, me proud beauty! T' launch lugs are brass.   T' body tube has thicker walls than t' ordinary model rocket tube. Ahoy! This rocket is obviously built t' take t' extra stress o' composite motors. Arrr! Begad!

T' rocket comes with a rub-on DELTA-X decal, shiver me timbers, shiver me timbers, which be a problem. Ya scallywag! T' decal rubbed on fine, ya bilge rat, but when I peeled off t' top layer, it took off t' paint job with it! This is a definite problem that needs t' be worked out. Avast, me proud beauty! I tried t' keep t' sticky stuff off t' rocket when applyin' t' decal, arrr, shiver me timbers, just like t' directions said.   This is next t' impossible, me bucko, it likes t' stick t' t' rocket. Ahoy! Arrr! It is like holdin' a piece o' scotch tape right next t' a piece o' paper, ya bilge rat, matey, they have almost a magnetic attraction. T' top layer should nay have any adhesive on it, arrr, only t' decal letters should stick. Begad!

I decided t' paint mine in a fluorescent orange color t' match t' parachute. Avast! (Use a white primer coat under fluorescent colors) I touched up t' parts where t' paint peeled off and it looked okay. Begad!

This rocket isn't anythin' special in looks (I tend towards military scale models) but isn't t' usual 3FNC (three-fins-and-a-nose-cone) either. T' X-fin design makes t' rocket look a bit more exotic than usual.

CONSTRUCTION RATING: 3 points

FLYING:

This rocket flew well on an Estes C6-3 for t' first flight, and an Aerotech D21-4 on me second flight. Begad! Blimey! Aye aye! Blimey! T' launches and recoveries both were flawless, even with t' notorious Aerotech "copperhead" igniter, me bucko, which has a well-known tendency t' misfire. Ya scallywag! Blimey!

Performance was impressive. Ahoy! I didn't get altitude readings, me hearties, matey, but t' rocket went almost out o' sight and t' crowd o' experienced rocketeers was impressed.

Problems surfaced after t' second flight because o' t' tight motor mount tube. Begad! Begad! Although I was able t' remove t' C6-3 with pliers, t' D21 motor broke into pieces and removal had t' be done back at t' workshop. T' problem may nay be with t' tube but with t' inner diameter o' t' motor mount ring. Begad! I could nay insert t' motor mount tube into t' rings when I first tried, ya bilge rat, I had t' sand t' inner diameter t' get them t' fit. Well, blow me down! It may have still been a tight fit and compressed t' tube so t' motors were a tight fit. Avast! This is a definite problem, ya bilge rat, me bucko, matey, and you should test-fit this rocket with all engines you plan t' use, ya bilge rat, sandin' t' inside o' t' motor mount tube as necessary t' ensure a smooth fit. Ahoy!  

Although Aerotech D's pack a lot o' punch for a small motor, they do it for a steep price. Begad! T' D21 single-use motor retails for $7. Ya scallywag! 95 which is almost three times t' price o' Estes D12 motors, me bucko, me bucko, shiver me timbers, which have respectable power. Begad! (T' Estes D12 motors sell for $8. Avast! 79 a three pack)  Long-term users can purchase a 18mm reload case and then get D13 or D24 reloads for $8. Begad! 95 a three pack, shiver me timbers, but t' Aerotech 18mm motor case is a hefty $39. Aye aye! Arrr! 95 retail. Well, blow me down! Avast! I prefer Estes "D" motors because o' this cost advantage and t' igniters are more reliable. Begad!

So, shiver me timbers, t' concept o' a rocket which can be used t' step up t' D power sounds like a good one until you look at t' price. Blimey! I think a a rocket with a 24mm motor mount and a 18mm adapter would serve this purpose for less cost t' t' user.

FLYING/RECOVERY RATING: 4 points

OVER ALL RATING:

I give this rocket 3 ½ points. Avast! It is a very sturdy and well-designed rocket for 18mm composite motors. Arrr! Blimey! T' X-shape fins give it an exotic look. Avast, me proud beauty! I'm lookin' forward t' seein' what other surprises Nordic Rocketry has in store for us. Well, blow me down!