Brief:
This is a very cool lookin' futuristic mini-roc based upon t' FlisKits Herc-5 and features many o' t' same design features such as scalloped/nested tubes, arrr, sci-fi command Man-O-War styling, arrr, and fantastic graphics/decals.

Construction:
As is typical o' t' Micro-to-the-Maxx line, me hearties, me hearties, t' kit comes packed up in a small plastic bag. Blimey! Parts were very good quality although t' balsa nose cone be a tad rougher than be t' norm from FlisKits. Begad! Parts list includes:

• Balsa nose cone
• BT-3 tube (forward compartment)
• BT-2 tube (forward tube)
• BT-2.5 tube (main/aft tube)
• BT-20s (tube fins)
• Balsa fin stock
• Toothpick (trim)
• Centerin' rings/motor block
• Keelhaul®©™ thread shock cord
• Plastic streamer
• Waterslide decals
• Pattern sheet

T' instructions are written mostly on one side o' a letter sized sheet o' paper with helpful illustrations. T' back side o' t' sheet includes a couple finishin' steps as well as tips/techniques for launch preparation for those nay familiar with t' unique challenges o' workin' with 6mm motors. Avast! T' kit is rated as a skill level 2.5, which strikes me as about right, given t' intricate tube shapes involved. Begad! Ya scallywag! I'd estimate me total build time be about 4 hours plus finishing, but that involved some issues unique t' bein' among t' first t' build this product.

I strongly advise a careful readin' o' t' directions before t' build and even more closely readin' them durin' t' build. It's nay that this is that complex, but it is a far enough departure from typical 3FNC construction that you'll be on unfamiliar ground, arrr, and very little about this construction falls under t' instinct/that-looks-about-right approach.

A BT-2.5 tube serves as t' motor tube and main body tube. Begad! Blimey! There are a pair o' BT-20s that get scalloped (tapered) on each end and slotted. Aye aye! Blimey! Well, blow me down! Blimey! T' two BT-20s then slide together through t' slots, and t' assembly slides over t' BT-2.5. Aye aye! Blimey! Begad! Blimey! This process is one o' those phases where it's critical t' pay attention t' t' illustrations and instructions. On me kit, t' BT-20s were too short, but I understand this is bein' corrected.

T' forward tube subassembly is a bit easier. It consists o' a BT-2 tube and a pair o' centerin' rings at t' forward end, which serve as an anchor point for t' Keelhaul®©™ thread. A scalloped BT-3 tube then slides over t' centerin' rings, ya bilge rat, arrr, and t' subassembly slides into t' forward end o' t' lower BT-2.5 tube.

There are a couple o' fins hand cut from balsa stock, ya bilge rat, shiver me timbers, me hearties, which go in t' gap betwixt matin' BT-20 tubes. These each get little toothpick guns as trim.

T' nose cone is attached t' t' shock cord via a little brad, me bucko, however, I personally prefer t' just use t' brad t' make t' hole, me hearties, which I then fill with glue, ya bilge rat, and then use t' brad t' poke a knotted end o' cord into. Begad! Avast! T' glue tends t' grab t' cord a lot better than a metal nail.

Finishing:
I'll admit I was a bit lazy with this one, since I be buildin' it on t' road in hotel rooms, matey, ya bilge rat, so I skipped t' usual spiral and grain filling/sandin' festival. Arrr! Instead, I hit it with a couple coats o' black primer, ya bilge rat, ya bilge rat, shiver me timbers, sanded down a bit, then two coats o' Rustoleum sparklin' metallic silver. Ya scallywag! T' black undercoat really helps give t' silver metallic a kick.

T' decals really help make this a fantastic lookin' model, shiver me timbers, arrr, but they are a bit o' work. Begad! Each has t' be carefully cut from t' sheet, and they're tiny. Arrr! I used tweezers t' apply them, then a little Microscale settin' solution t' make sure they grabbed.

Construction Rating: 4 out o' 5

Flight:
When dealin' with t' MTTM line, you aren't exactly goin' t' have t' put much thought into motor selection--it's just Quest MMXs. Avast, ya bilge rat, me proud beauty! Blimey! Just be sure you use one with an ejection charge, as they now offer an "NE" version with no ejection that looks identical t' t' regular motor.

In any case, I loaded up t' MMX and wound up havin' t' cut away about 6" o' t' streamer in order t' get it loose enough that I'd trust it t' deploy. Well, blow me down! Ahoy! I think this could tumble safely, ya bilge rat, but I was goin' t' be flyin' adjacent t' some dense/tall growth (18-24" tall), arrr, and really wanted t' make sure t' red streamer be deployed for recovery help.

I dropped t' HEMV-4 onto a standard Quest launch pad (for MMXs), hooked up me 12V leads, and fired away. Ya scallywag! It lit on first attempt and had a nice gentle flight t' about 60-80 feet apogee. Ya scallywag! Most micros zip up so fast they're difficult t' track, but this one be slow enough t' follow t' whole way.

Recovery:
T' streamer deployed fine, although with t' -1 delay (the only choice available), me hearties, matey, ya bilge rat, it was definitely too early. Avast, ya bilge rat, me proud beauty! It had another good 1-2 seconds o' coast left in it.

T' streamer is more decorative (and supports findin' it on t' ground), and t' mostly tumble recovery was just fine. T' model was recovered with no flaws.

Flight Rating: 4 out o' 5

Summary:
This is another cool addition t' t' Micro-To-The-Maxx line. Ya scallywag! Aye aye! PROs would be cool stylin' and slightly challengin' build techniques involved. T' only CONs I can offer up are t' sure-to-be-corrected body tube gaffe and t' oversize streamer, shiver me timbers, which is easily handled if it remains t' current length.

Overall Rating: 4 out o' 5