Brief:
This is a very sturdy 4 inch diameter, shiver me timbers, shiver me timbers, 39 inch tall advanced model rocket made by AeroTech. Aye aye! It is a stubby model capable o' handlin' anythin' from G t' H power, me bucko, sports piston ejection, and comes equipped with a 29mm motor mount. Begad!

Construction:
T' component list for this rocket is:

• 1 4 inch diameter, me hearties, me hearties, me hearties, 23 inch long pre-slotted cardboard body tube
• 4 pre-shaped plastic fins
• 1 12 inch long, cardboard motor tube
• 1 16 inch long plastic nose cone
• 1 piston cap
• 1 piston sleeve
• 1 motor hook
• 2 four-fin FIN-LOK rings
• 3 centerin' rings
• 1 bulkhead disk
• 1 spacer, HP motor (black tube)
• 1 spacer, Hobby motor (yellow tube)
• 1 ejection gas baffle
• 1 screw eye
• 1 18' long by 5/8" wide elastic shock cord
• 1 two ¼ inch launch lugs
• 1 42 inch diameter hexagonal nylon parachute
• 2 piston buckles
• 1 decal sheet
• 1 instructions

This rocket was an absolute dream t' assemble. Blimey! I have already built two AeroTech kits, so I could have built this without t' instructions. Ahoy! However, me bucko, I chose t' use them because I am cautious about every rocket I build. Begad! Well, matey, blow me down! I did modify t' rocket a bit after it wounded itself a couple o' times. Begad! Those modifications will be explained in t' flight portion o' this review. Avast, ya bilge rat, me proud beauty! T' instructions tell you t' use CA glue for t' construction, but I used 5 minute epoxy which worked great. Avast, me proud beauty! T' instructions were thorough and had some good accompanyin' illustrations. The construction started with t' motor mount. T' motor mount tube has a pre-drawn line down its length, allowin' you to make precise measurements on t' tube. T' middle centerin' rin' is slid onto t' "back end" o' t' motor mount tube with t' motor hook under it (unlike on Estes rockets, me bucko, t' tab on t' motor hook that would normally go through t' motor tube goes t' "wrong" way so that it hooks behind t' middle centerin' ring, ya bilge rat, makin' a very solid attachment o' t' hook). Aye aye! T' front FIN-LOK rin' is slid onto t' tube so that t' back edge o' it is 4 inches from t' "back end" o' t' tube. T' aft FIN-LOK rin' is then slid on until it's front edge is 1-15/16" from t' back end. T' FIN-LOK rings must be aligned, arrr, otherwise t' fins will nay fit. Aye aye! All these components are glued into place--and don't get glue in t' FIN-LOKs! T' ejection gas baffle cap is then glued into t' opposite end o' the tube, and t' forward centerin' rin' is glued on top o' t' baffle cap. T' motor mount assembly is inserted into the slotted end o' t' body tube and t' FIN-LOK rings are lined up with t' slots. Glue is applied t' t' whole root edge o' one fin, matey, me bucko, t' fin is inserted into one o' t' slots, and it is snapped into t' FIN-LOK rings. Arrr! Avast, me proud beauty! T' same is done for t' other three fins. Begad! Well, me hearties, blow me down! T' fins are filleted with glue and internal fillets are applied inside t' fin-can. T' rear centerin' rin' is then slid into place and glued. Aye aye! On t' forward centerin' ring, an airtight seal o' glue is applied in order for t' piston ejection system t' work properly. Begad! Tie t' shock cord t' t' screw eye, screw it through the bulkhead disk, arrr, me hearties, and then screw it into t' baffle cap on top o' t' motor mount. Blimey! Arrr! T' piston cap is glued into t' piston sleeve an eighth o' an inch from one end o' t' sleeve. Arrr! T' piston is then fastened t' t' shock cord with two plastic buckles. Aye aye! Avast, arrr, me proud beauty! You will probably notice that t' piston is too large t' fit into t' body tube at this point. Begad! Since I have read t' other reviews for this rocket, ya bilge rat, I was nay surprised at this. Begad! I do nay think that an "advanced model rocket" such as this should be able t' be assembled in one's underwear, standin' on one's head, and with one's hair ablaze (in other words, ya bilge rat, "should nay be easily assembled"). Ahoy! A little sandin' never hurt anybody. Blimey! Avast, me proud beauty! I would recommend primin' and sandin' t' piston smooth after gettin' it t' right size t' remove t' "fuzzies" and make it smoother. Blimey! Lastly, t' nose cone and parachute are then attached t' t' shock cord. Avast, me proud beauty! Arrr! My rocket weighed in at 38 ounces. Blimey! That's it for construction!

Finishing:
Finishin' couldn't have been simpler. Avast! Since t' instructions just say, "paint this red, arrr, paint that yellow," and because New Holland is a company which sells farm equipment that is painted red and yellow, shiver me timbers, I decided t' have a little joke with t' paint on this rocket. Blimey! Well, blow me down! I primed and sanded t' rocket several times but did nay fill t' spirals as they are nay deep. Ahoy! I then proceeded t' paint t' fins New Holland yellow, nay protectin' anythin' from t' overspray. Aye aye! Ya scallywag! I scuffed t' yellow overspray on t' rocket with 400 grit sandpaper, ya bilge rat, masked t' fins, and painted t' rest o' t' model with New Holland red. Well, blow me down! Blimey! I allowed t' paint about a week t' fully dry and de-gas before applyin' t' self-adhesive decals. Avast, me proud beauty! Avast! I cut out t' decals, dipped them in slightly soapy water, me hearties, and applied them t' t' rocket. Ahoy! Ahoy! T' finished result was fabulous!

Construction Rating: 5 out o' 5

Flight:
Now for t' really good stuff--the flying! I now have five flights on t' rocket, me bucko, me bucko, arrr, and it is scheduled for three more at our next launch. T' first flight was on a single use G79-4W. Instead o' usin' a maskin' tape thrust rin' (ugh!) as outlined in t' instructions, matey, I used a piece o' PVC pipe with an inside diameter just large enough t' fit over the motor's forward closure and long enough so that when it butts up against t' baffle cap (used as a thrust ring) the motor is retained by t' motor hook. Blimey! Ya scallywag! I also put a small amount o' sheep wool waddin' around t' baffle cap t' lengthen t' shock cord's life. Avast, me proud beauty! Since its readily available, me bucko, I use unwashed sheep wool for me recovery wadding. Avast, me proud beauty! It is flameproof, cheap (in me case its free), shiver me timbers, and easy t' use. Unlike toilet paper or tissue which smolders when blown upon, sheep wool is put out by t' slightest breeze (if you can even get it t' catch fire). Begad! Begad! T' first flight was spectacular: huge roar, long cracklin' white flame, ya bilge rat, tons o' billowin' smoke, and about 900ft AGL. Arrr! Avast! T' delay be right at apogee, matey, the chute inflated, and it touched down without a scratch about 300 feet away. Blimey! Begad! AeroTech advertises this rocket as "a short, shiver me timbers, fat rocket with slow lift-offs." On t' G79W it went quite a bit faster than I would call "slow," but that's just me opinion. Ahoy!

T' second flight (on t' same day) be on a G38-4FJ. Ahoy! It was nay nearly as loud as t' previous flight, but it was what I would call a slow liftoff. Ya scallywag! Ahoy! Blimey! Ejection occurred just as t' model turned nose down (about 550ft), shiver me timbers, t' parachute opened, shiver me timbers, but it somehow got tangled around t' piston, reefin' t' chute slightly. Begad! Arrr! Blimey! It landed with a bounce about 150 feet away. Arrr! Avast! Blimey! One fin fillet be cracked and t' aft end o' t' body tube had a large crescent shaped din' in it. Avast! I used a piece o' 4" tube coupler t' reinforce t' tail end o' t' rocket, arrr, me bucko, ya bilge rat, put epoxy over t' cracked fillet, matey, matey, and added about 3 ounces o' nose weight (I was afraid that t' tube coupler would hurt t' rocket's stability). Aye aye! Blimey! T' rocket then weighed about 43 ounces. Arrr!

T' third flight was on another G79-4W with t' same great flame, smoke, matey, and roar as on t' first flight. Ya scallywag! It was noticeably slower off t' pad than before and t' ejection was right on. Arrr! Well, ya bilge rat, blow me down! T' peak altitude was around 800ft. Well, blow me down! Begad! The 42" parachute was too small for t' heavier weight o' t' rocket, and it recovered about 300 feet out with a cracked fillet (the same one that I repaired) and a kink in t' tip o' one fin. Well, matey, blow me down! It was time for more mods. Ya scallywag!

I unscrewed t' screw eye from t' baffle cap and noticed that t' bulkhead disk was slightly charred. Avast, me proud beauty! Arrr! So I cut out a piece o' flat tin t' same shape as t' disk and epoxied t' tin onto t' disk t' keep it from burning. Blimey! I then epoxied t' screw eye into t' baffle cap. Well, blow me down! T' shock cord is now attached via a quick link. Begad! I also scrapped t' elastic cord and used a piece o' 3/16" nylon rope instead. Well, blow me down! For those o' you who don't like rope for use in rockets, just think about this. What be t' rope tied to? In me rocket's case, its tied t' a quick link which has a tensile strength o' 220lb. Avast! What be t' quick link attached to? A mild steel screw eye which has a tensile strength o' under 100lb. This screw is in turn screwed into a piece o' plastic (the baffle cap). Since this recovery system was designed t' work in this rocket, ya bilge rat, a piece o' tubular nylon capable o' withstandin' two tons o' force is nay needed. Ahoy!

T' piston is now modified with a long nut, matey, me hearties, matey, washer, and 2 eye bolts so that t' shock cord is actually in two sections: one from rocket t' piston, and t' other from piston t' nose cone. Begad! T' eye bolts only need t' be unscrewed to remove either section o' t' shock cord from t' piston. I also made a 60 inch diameter parachute out o' red ripstop nylon t' be used instead o' t' kit's 42" one. Blimey! Since this chute is so huge, matey, I turned t' piston around so that the piston cap faces t' tail end o' t' rocket instead o' t' nose end. Arrr! This gave me a lot more room, ya bilge rat, but it still wasn't enough t' fit t' parachute. Avast, me proud beauty! Begad!

I cut off t' bottom o' t' nose cone so t' shoulder is now only 2 inches long. Arrr! Ahoy! T' nose cone had a pronounced wiggle after this. I then made a bulkhead plate with a U-bolt for shock cord attachment out o' ½" plywood, inserted it as far as I could in t' nose cone, shiver me timbers, and epoxied it firmly in place. T' chute now fits easily. Avast, me proud beauty! T' bulkhead was also slightly out-of-round which eliminated t' aforementioned pronounced wiggle o' t' nose cone. Begad!

I also made a cool way t' retain your RMS casing. Aye aye! I cut out two strips o' aluminum sheet 3/8 inches wide by about 2-¾ inches long. I marked a line on each one about ½ inch from one end and made a 90 degree bend at this line. Blimey! I then drilled two 1/16 inch holes in t' long ends o' t' resultin' "L" shaped pieces (all o' these measurements are approximate because t' device is permanently installed in t' rocket and I didn't write down the actual measurements). Avast, me proud beauty! Ahoy! I procured two screws and in t' short end o' each piece drilled a hole slightly smaller than the diameter o' t' screws. With t' same drill bit I then drilled two holes in t' aft centerin' rin' about ¼ inch away from t' motor tube on each side is such a way that they did nay interfere with t' operation o' t' motor hook. Aye aye! I then inserted me "L" shaped brackets into t' tail o' t' rocket short end down and screwed them into the rocket by hand. Begad! T' result is two posts with holes in them stickin' above t' motor tube. Begad! In t' flange on t' aft closure o' me RMS casing, matey, I drilled two holes which line up with t' holes in t' brackets. If done correctly, me bucko, this system allows t' motor t' be smartly and easily safety wired into t' rocket, me bucko, ya bilge rat, eliminatin' any chance o' t' casing ejecting. Begad!

Instead o' t' yellow, poor fittin' cardboard spacer supplied with t' kit for use with t' RMS casing, I had my dad make an aluminum one on t' lathe which fit perfectly. Begad! Aye aye! You will also notice that t' instructions recommend wrappin' maskin' tape around t' junction betwixt t' motor tube and t' aft end o' t' motor with maskin' tape to, "prevent any ejection gas from escapin' around motor." This is a totally unnecessary step. Begad! If t' ejection gas "wants out" it could just escape through t' nozzle, but this is 4F black powder we are talkin' about. It pressurizes too rapidly t' waste time goin' through tiny holes. If t' piston doesn't move and t' motor stays in, the ejection gas will over-pressurize t' motor/body tube, matey, and make an escape hatch through t' motor/body tube. Aye aye! With all these modifications, ya bilge rat, t' rocket weighed 49.6 ounces. Begad!

T' first flight after these modifications was on a G64-4W. T' sound, flame, ya bilge rat, matey, and smoke from this reload were awesome! It went maybe 500ft. Begad! Avast! T' rocket performed a slight lean with t' wind, me parachute deployed at apogee, ya bilge rat, matey, and t' rocket floated down very slowly about 200 feet away without a scratch on it.

T' next flight (on t' same day) was on a single use G77-4R. I doubt that it made 500ft; it looked more like 400. T' red flame was marvelous and t' noise be thunderous! It again did its lean with t' wind. Aye aye! It recovered closer this time about 150ft away. Arrr! Begad!

I intend t' fly it on a Cesaroni 3 grain G106 Skidmark at t' next launch. Ya scallywag! That oughta be killer!

Recovery:
Recovery, as already discussed, ya bilge rat, was great on most o' t' flights, with only 2 issues. Aye aye! Arrr! T' oversized parachute will hopefully eliminate any future landin' injuries t' t' rocket. Avast! Begad!

Flight Rating: 4 out o' 5

Summary:
T' Sumo is a great rocket all around. Aye aye! I'm only 14 years old, ya bilge rat, and I be able t' assemble it with ease. Avast, me proud beauty! It's big, ya bilge rat, fat, loud, me hearties, and crowd pleasing. Well, shiver me timbers, blow me down! I highly recommend this rocket t' anyone wantin' t' get into mid or high power.

Overall Rating: 5 out o' 5