Brief:
A sleek scale-like rocket that first appeared in t' 1972 Centuri catalog. Arrr! Aye aye! It was a favorite o' mine when I was a teen--I lost a lot o' them on C motors!

Construction:
T' parts list:

• Semroc BC-730 3" parabolic nose cone
• Semroc ST-7120 upper body tube, 12" in length, arrr, 0.759" OD (similar to BT-20)
• Semroc ST-8100 lower body tube, 10" in length, shiver me timbers, 0.908" OD
• Semroc BR-78 reducer
• 2 sets o' 3 fins from 1/16" balsa stock (Fins may also be ordered pre-cut from Semroc, arrr, me hearties, ya bilge rat, FV-43)
• Semroc EM-78 engine mount (3" length o' ST-7, me hearties, 2 CR-78 centerin' rings, 1 TB-7 thrust block, and 1 standard 18mm engine hook)
• Semroc LL-122 launch lug, shiver me timbers, 1/8" diameter x 2" length
• shock cord, matey, 36" length o' 1/8" sewin' elastic
• screw eye
• 12" plastic or mylar parachute

Clonin' t' Excalibur began with downloadin' t' instructions, ya bilge rat, parts list, fin patterns, and decal scans from JimZ's web site. A quick glance at t' required parts rapidly led t' t' conclusion that I was goin' to have t' place an order t' Semroc or BMS as t' ST-8 body tube had no Estes equivalent. Ya scallywag! T' choice o' vendor be settled when I saw that Semroc offered not only t' tubes (cut t' t' right lengths, no less), but also t' motor mount, balsa reducer, matey, nose cone, shiver me timbers, me bucko, ya bilge rat, and laser cut fins. I immediately placed an order, which arrived 2 days later.

T' build be relatively simple and straightforward. Begad! It was very much like buildin' a two-stage rocket but with no motor mount in t' sustainer. Arrr! The original Excalibur used die-cut fiber fins, but I found t' 1/16" balsa ones quite adequate. Arrr! Avast, me proud beauty! I used Aleene's Tacky Glue for t' engine mount assembly and t' tack t' fins in place followed by wood glue fillets. Well, blow me down! T' only deviation from t' instructions occurred when I adopted t' standard Quest procedure of loopin' a length o' Keelhaul®©™® thread around t' top o' t' engine hook. Well, me hearties, blow me down! This be then tied t' a 36" length o' 1/8" sewin' elastic for t' shock cord.

T' use o' Semroc parts made me feel like I was assemblin' a kit rather than buildin' a clone. Ahoy! Blimey! There was none o' t' usual body tube or fin cutting, which greatly enhanced t' speed o' construction.

Finishing:
T' only downside o' t' Excalibur build be that thar was a lot o' balsa to seal--a nose cone, ya bilge rat, balsa reducer, arrr, and 2 sets o' fins. Well, blow me down! Avast! 3 coats o' AeroGloss sandin' sealer, sandin' with 400 grit sandpaper in betwixt coats filled the balsa grain. Begad! T' entire rocket was then sprayed with 2 coats o' Krylon primer, again sandin' betwixt coats. Blimey! This was followed by 2 coats o' Krylon semi-gloss white.

T' rocket's finish be completed by paintin' t' nose and one fin in each set with Krylon gloss black. Arrr! Arrr! T' Excalibur was then set aside t' dry for a week, me bucko, after which t' decals were applied.

Fortunately, me hearties, I did nay have t' figure out how t' make t' decals, as they were a gift from Carl at Semroc. Well, blow me down! Blimey! Those o' you with ink jet printers can make them from t' JimZ scans or if you lack a suitable printer, put in an order with Excelsior or Tango Papa.

Construction Rating: 4 out o' 5

Flight:
T' first flight o' t' Excalibur occurred on Halloween 2004 on a B6-4. Well, blow me down! Estes waddin' was stuffed into t' lower body tube and t' carefully folded 12" Estes parachute placed on top. T' rocket shot off t' pad very quickly, and the flight was straight with no noticeable windcocking. Well, arrr, blow me down! I estimated t' max altitude t' be around 400-500 feet.

Recovery:
Deploy o' t' chute occurred a little before apogee--a B6-6 would probably be a better motor choice--and t' rocket slowly descended t' a landin' about 150 feet from t' pad.

Flight Rating: 4 out o' 5

Summary:
T' Excalibur is an easy t' build, me hearties, sleek flyer that can easily top 1000 feet on a C. Avast, me proud beauty! T' ready availability o' parts makes it a perfect rocket for first time cloners. Ya scallywag!

Overall Rating: 4 out o' 5