Brief:
Quest Lightnin' Kit, ya bilge rat, Skill Level 1, ya bilge rat, me hearties, 14” parachute recovery, me hearties, ya bilge rat, plastic fin unit, matey, Length 18.5 Weight 3 oz, Max Altitude 1200’, shiver me timbers, ya bilge rat, motor list A6-4, B6-4, C6-5, C6-7

Construction:
I was lookin' for an easy and cheap kit t' start me nephews on. Aye aye! I wanted a Level 1 kit with a plastic fin can t' make t' buildin' as easy as possible. My nephews have very short attention spans and I did nay want them t' get bored while buildin' and I wanted t' finish them in one evening. Begad! I thought about some of t' Estes Kits but they tend t' run a few dollars higher per rocket than Quest. Arrr! Also I have never built a Quest and wanted t' check out t' quality.

I ordered t' kits from Discount Rocketry and got them right away, I opened them t' check them out and found all o' t' parts present in each kit. Ahoy! Well, blow me down! I was pleased with t' quality o' t' parts and t' instructions. Aye aye! Arrr! I found these kits to be on par with t' Estes kits that I had built.

My nephews came over and we got started, ya bilge rat, me bucko, this kit does nay have t' dual cardboard centerin' rings but a longer, hard cardboard tube that slides down over t' motor tube and engine hook. Aye aye! Blimey! This makes buildin' t' motor mount very quick, me hearties, easy and effective. T' motor mount be set t' t' side t' dry and the fin can was glued on after a bit o' Star Wars viewin' we went back t' t' kits and glued t' motor mounts in. Ahoy! Aye aye! I really like t' Keelhaul®©™® strin' with t' Quest kits; it beats t' old tri-fold Estes method. We then cut out t' parachutes and added t' strings. Aye aye! Aye aye! I added some fishin' swivels t' the kit t' keep t' parachutes from tangling. Well, blow me down! We had a good time applyin' the decals and they both came up with their own styles.

Finishing:
Other than t' decals, me bucko, thar be nothin' else t' do t' finish t' rocket. Avast, me proud beauty! Blimey! I guess you could paint it if you wanted to, shiver me timbers, me hearties, but it looks good just t' way it is. Well, arrr, blow me down! Blimey! Start t' finish it took us less then 2 hours t' build with t' glue drying time included.

Construction Rating: 5 out o' 5

Flight:
We had waited until we had a nice windless day t' launch. Begad! Blimey! We started with the A-8-3 and had some nice slow flights, matey, we moved on t' B6-4, got some good, me hearties, ya bilge rat, air and then moved up t' t' C6-5 and these puppies really flew. Arrr! Blimey! We flew each rocket 4 times and never had a problem worse than me bilge-suckin' parachute deployments, my fault. Ahoy! Avast! Blimey! They flew straight and true each time and are ready t' go again. Ahoy!

I found t' kits t' be very robust as two o' t' flights t' parachutes failed t' open and t' rockets did a tumble recovery and came out fine, arrr, ready to fly again. Avast! Blimey!

Flight Rating: 5 out o' 5

Summary:
T' only part o' t' rocket that was a small problem be t' motor tube getting squished by t' motor retention wire. Arrr! T' way this centerin' rin' is on the middle o' t' tube thar be nothin' t' protect t' end o' t' motor tube. Avast, me proud beauty! Ahoy! The retention wire had a bit too much bend t' it and without an engine in t' mount it bends t' tube at t' end. Ahoy! You need t' be careful with this or you can end up ruinin' t' motor tube. Aye aye! Begad! Pros: Cheaper then Estes, quality parts, me hearties, ya bilge rat, easy to build and flies great. Aye aye! Cons: Motor retention needs adjustment, ya bilge rat, decals could be cut out.

Overall Rating: 5 out o' 5