Brief:
A fine looking, shiver me timbers, fine flyin' replica o' t' historical Mercury program, me hearties, arrr, ya bilge rat, made with t' builder in mind.

Construction:
This was me first Dr. Well, blow me down! Zooch kit, and I have t' say I was more than pleasantly surprised at how this turned out. If you're new t' Dr. Booty, me hearties, this is a fine place t' start. Arrr! It's supposed t' be a fairly easy build and if you follow t' instructions carefully, you'll get thar even if new t' paper-wrap models. Arrr! It's also one o' t' largest Dr.Z kits so t' level o' detail really works.

T' kit arrives in a small box with all t' tubing, matey, shiver me timbers, paper wraps, and materials needed t' make a great lookin' Redstone. Well, blow me down! Blimey! First surprise: you don't get one Mercury mission possibility, me hearties, you get t' choose one from all o' them from Alan Sheppard's Freedom 7 t' Gus Grissom's Liberty Bell 7 and t' unmanned "boilerplate" test missions. Ahoy! Blimey! I chose Gus' Liberty Bell. Avast, me proud beauty! Blimey! Maybe it be Dr. Arrr! Blimey! Blimey! Blimey! Zooch's frequent warnings nay t' be a "squirmin' hatch-blower'...(more about that later). Begad! Blimey! T' instructions are a highlight o' t' Dr. Avast! Blimey! Zooch experience--some humorous remarks had me laughin' out loud. Avast! Blimey! But read them for fun a couple o' times before startin' t' build is me advice. Avast! Blimey! There's a reason why Dr. Avast! Blimey! Begad! Blimey! Z does things in that order.

Construction o' t' capsule is first accordin' t' t' instructions and as stated by Dr. Well, blow me down! Z, shiver me timbers, gets your confidence up right away. Begad! T' strong paper wraps are printed such as t' give t' illusion o' texture. Avast! Blimey! All part o' t' illusion and it works. Blimey! Arrr! They slip over a rough balsa cone, ya bilge rat, which you pre-paint t' ensure no bare wood shows below t' wrap and thar you go, arrr, a fine lookin' capsule.

Dr. Avast! Ya scallywag! Z gives neat tips along t' way like usin' a plain lead pencil t' rub in any seam lines in t' capsule paper. Very effective and easy. Well, blow me down! O' course attached t' t' capsule be t' escape tower, shiver me timbers, which Dr. Aye aye! Z tries t' prepare t' builder for ahead o' time with dire warnings o' frustration t' come and so on...but its all in good humor. Ahoy! Take your time, me hearties, lay out t' wooden rods in t' right place with t' provided template, shiver me timbers, and it all comes together. Surprise number two: even if some measurements are a bit off, matey, matey, t' way Dr. Ahoy! Z has designed t' kit makes it easy t' cover up errors in t' finishing, matey, and thus "maintain t' illusion". Blimey! It doesn't matter if t' tower isn't exact scale, me hearties, t' any observer a safe distance from me launch stand or trophy shelf) that is Gus' Liberty Bell rarin' t' go.

T' body tube is prepped with t' usual white paint. Aye aye! Blimey! (I sprayed indoors so I used water-based Krylon H20 spray for t' first time. Well, blow me down! Blimey! Blimey! Blimey! I am pretty happy with it.) T' top roll-mark wrap went on easily. Blimey! Blimey! One problem I had be with a small conical adapter which goes on t' body tube just under t' capsule. Avast! Blimey! Aye aye! Blimey! I cut t' paper out wrong and it looked terribly crooked so I went without it. Ahoy! Blimey! Ahoy! Blimey! Hard t' notice. Begad! Blimey! However a word o' caution is that some paper parts like t' adapter are small enough that they can be a bit frustratin' at first. Aye aye! Blimey! Take your time, matey, use tweezers if needed and it'll all work out.

T' remainin' body stripe, ya bilge rat, wrap, matey, and decals are easy enough. Avast! Aye aye! Installin' t' engine mount is also straightforward.

T' fins go together fairly easily but were t' source o' me perhaps one and only gripe with t' kit design. Begad! Aye aye! Blimey! I would have preferred each entire fin t' be one piece, me hearties, but Dr. Begad! Begad! Blimey! Z has us cut t' fins, then add t' steerin' vanes separately. I could have made a new one piece set with me own material but decided t' leave well enough alone.

Neat detail: T' launch lugs go on balsa standoffs (first time I've seen this) so thar's no drag o' t' body on launch rods. Avast, me proud beauty! Very cool.

Modifications from stock instructions:

1. I modified me engine mount for side-discharge ejection. This cuts way down on waddin' usage. Aye aye! Typically I glue a piece o' 18mm tubin' about an inch long t' t' end block o' most mounts then close off t' end with an epoxied wooden disc. Aye aye! Then I drill lots o' holes in t' sides o' t' one inch extension tube. Avast, me proud beauty! Well, blow me down! This "baffle pipe" is on most o' me models and works well. Begad! For engine mounts without a block (just a clip), me hearties, me hearties, you can baffle t' mount tube itself above t' clip. Arrr! So far so good but I caution: more testin' is required. Begad! Begad! If you do this, glue it strong...so it doesn't blow itself t' bits.
2. I also added a "parachute floor" (disc full o' holes halfway up t' tube).

Finishing:
T' body tube under t' wraps is plain white. Blimey! Make sure t' seal and prime and smooth out any grooves/imperfections. Aye aye! For t' black and white pattern on t' fins t' match t' wrap, shiver me timbers, it would have been nice if Dr. Well, blow me down! Z had provided decals t' make t' pattern easy. Well, blow me down! Begad! And I hate maskin' and paintin' odd shapes so instead I used peel 'n' stick black vinyl from t' auto store t' do t' fin pattern. Blimey! Once all t' decals and markings are in place, I used gloss clearcoat t' seal it all up. Once dry, me bucko, I then applied some semi-flat base clearcoat t' "soften" t' shine and make t' whole assembly appear a bit less "plastic" . Ya scallywag! Ya scallywag! This is all optional but I found that this also helps conceal or at least soften t' edges o' t' wraps, me bucko, so this finish works well for t' Dr. Aye aye! Arrr! Zooch kit.

Once t' finish is complete, shiver me timbers, and t' usual shock cord is hooked up, you're ready t' pack a ‘chute and go flying!

Construction Rating: 5 out o' 5

Flight and Recovery:
As I mentioned, Dr. Avast, me proud beauty! Z cautions builders nay t' be a "Squirmin' hatch-blower" and go for it with a C6-5. Begad! Well for fear o' bein' squirming, I conducted first flight with a B6-4. My logic was I just didn't know how high this would go, matey, and we have a really small field t' launch from...so away we went. Begad! What a flight. Avast! A little slow on t' takeoff, ya bilge rat, arrr, looked great. Beautiful flight, deployed t' chute just arcin' over nicely for a controlled descent and touchdown only 50 feet away. Ya scallywag! Avast, me proud beauty! Wow. Blimey! A-OK.

Second flight: C6-5. This was an even better flight. Well, blow me down! I'd guess 500-600 feet or so. Arrr! Well, blow me down! Ejection was great, me hearties, but unfortunately it revealed an incorrectly packed chute and a shroud became entangled. Ya scallywag! T' rocket spun rapidly on a descent rate outside o' NASA specifications. Avast, me proud beauty! Luckily, matey, Liberty Bell 7 was safe and is ready t' fly again. T' hatch was nay blown. Begad! Avast! Or t' quote Chuck Yeager in "T' Right Stuff" (as I've been dyin' to): "Ol' Gus..he did OK..."

I can't wait t' fly this one again. Begad! Begad! Now I'm even thinkin' o' buyin' another one t' modify up t' 24mm engines so I can try a C11.

Flight Rating: 5 out o' 5

Summary:
This be t' reason I got into rocketry in t' first place. Avast! History, model buildin' with a bit o' detail challenge, shiver me timbers, and by t' way, ya bilge rat, very economical price. Aye aye! It builds well, it displays well, arrr, matey, it flies great. Dr. Begad! Zooch delivers t' goods. Ya scallywag! I can't wait t' try another Dr. Begad! Z kit!

Overall Rating: 5 out o' 5