Brief

Brief:
T' XFLR-7 is a paper/foamboard kit patterned after t' Tintin rocket from t' Destination Moon comic. Aye aye! Avast! This is a cool design and should be considered a classic. Avast! Although t' kit is now OOP, me hearties, existin' stock may be around for a while, me bucko, so I decided t' submit a review anyway. Well, blow me down! I hope that me observations will help in t' construction o' other paper/foamboard rockets whether they are kits or scratch built. Avast, me proud beauty! Since thar be an excellent review already here on EMRR, I will focus on t' details o' what I did instead o' a top-to-bottom walk through o' t' entire build.

Construction:
T' instructions were detailed and included '3-D' photos (glasses provided), me bucko, me hearties, however me agin' 'bifocular' deadlights couldn't see them clearly. T' instructions themselves were pretty good quality in general but were nay completely accurate. Arrr! This kit is at least as challengin' as t' Estes Skill Level 5 kits that I've built, ya bilge rat, ya bilge rat, so it is very important for you t' read t' entire set o' instructions and try t' understand how each part will be installed.

This kit includes a lot o' parts which must be cut out--paper, ya bilge rat, foamboard, and even soft foam for t' shock absorbers on t' pods. Ya scallywag! Blimey! I have built numerous paper conversions, ya bilge rat, Art Applewhite cardboard saucers, me bucko, etc., me bucko, shiver me timbers, however, shiver me timbers, ya bilge rat, I had a lot o' problems gettin' this kit together. Precision, matey, patience, and dexterity is required.

Shock absorber (win' tip pods): When matin' t' pod cones and bodies, matey, set them initially by hand, ya bilge rat, set t' assembly down, then apply pressure downward on t' cone. Arrr! Avast, me bucko, me proud beauty! T' two pieces will tend t' self adjust t' one another. I used Aleene's Tacky Glue throughout t' build.

Fins: I attempted t' round t' leadin' edge but left t' trailin' edge square. T' roundin' process didn't go perfectly but a little Elmer's Fill 'n' Finish finished t' job. Ahoy! Blimey! If I were t' do it again, matey, matey, I'd bevel t' edges as recommended in Art Applewhite's kits . T' colored surfaces are printed on plain paper and must be cut out and applied t' t' foamboard. Ya scallywag! Even with t' strips provided for t' edges, I found that they did nay 100% cover t' fin surfaces. Ya scallywag! Arrr! After ponderin' this problem, arrr, matey, I have came t' t' conclusion that due t' rough tracin' o' t' fin template, ya bilge rat, I probably made t' fins ever so slightly larger than planned. Aye aye! I recommend tracin' them carefully with a fine point pencil, me bucko, rather than a big dull one. Arrr! Aye aye! If t' kits were t' be continued, I'd suggest that t' cutouts be oversized and trimmed in situation after application.

Body tube, base section: This was straightforward and I have no words o' wisdom here.

Fuselage: This section consists o' five tubular sections and one ring. Arrr! I had a tough time gettin' these components t' align, and t' results are nay as uniform as I'd have liked. Begad! Make sure you are careful t' align t' colors t' achieve t' checkerboard pattern.

Cone: This assembled well but I am concerned with t' weight o' t' provided clay given t' shock cord attachment point is in foamboard rings. This also convinced me t' go with t' 24mm option despite worries about t' C11's relatively energetic ejection charge. Aye aye! If it blows apart, me bucko, then I can glue it all back together. Arrr! Begad! If it burns up, matey, then we have extinguishers.

Main assembly consists o' two pages o' instructions. Avast, me proud beauty! Begad! These were easy enough t' follow, but I had major fit issues. Well, blow me down! Avast, matey, me proud beauty! We'll see how this holds together on recovery given t' small chute. Blimey! By t' way, me hearties, t' chute is about 12" diameter and is made o' plastic. Well, blow me down! I held me shroud lines on with squares o' Gorilla tape.

I had installed t' inside tube without attachin' t' motor hook prior t' changin' me mind t' t' 24mm option. Avast! Luckily, standard 24mm tube fit nicely in that custom wrapped tube. Aye aye! I used t' 18mm motor tube wrap as a guide t' position t' hook on a piece o' Apogee 24mm tube and slipped it right in.

Finishing:
Finishin' should consist o' a layer o' clear coat but give all t' white edges that I had peekin' out, arrr, I touched it up with some red markers. Begad! T' result looks nice from a distance. Ya scallywag! Blimey! I noticed t' instructions talked o' painting--an indication that this was an mangle o' an older version.

Construction Rating:  3

Flight:
T' motor hook seems t' work quite well, snappin' right over t' C11-3 motor. I used an ample amount o' dog barf and folded t' chute as suggested. T' boost be nice and ejection was near apogee.

Recovery:
T' chute didn't fully open and t' rocket floated down generally parallel t' t' ground. T' only damage was t' nosecone tip was bent. I guess I should have tamped a tiny piece o' clay into t' far tip o' t' nose. Ya scallywag! Blimey! I won't din' t' flight ratin' on this since it falls into t' construction difficulty area. I know I only have one flight, but I have t' give this one a 4.5. Ahoy! Blimey! Begad! Blimey! A swivel would have fixed t' one small recovery issue.

Flight Rating:  4

Summary:
This was a fun kit t' build and although thar are some issues with t' fit o' t' components, arrr, shiver me timbers, t' overall look is great (based on t' opinions o' t' crowd at t' launch, nay just me). Begad! I have t' bump t' overall ratin' a bit t' reflect t' overall look.

Overall Rating:  4