Brief:
This is an AeroTech Mustang fin can with longer carbon fiber body.

Modifications:
After an incident involvin' high speed soil mechanics, ya bilge rat, ya bilge rat, arrr, I had previously modified an AT Mustang by extendin' t' body (see mod article "MOOSEtang"). After several successful flights, it again suffered a top soil overdose and provided me with yet another opportunity t' improve it. Blimey! Arrr! I had been makin' carbon composite tubin' and decided t' rebuild it usin' this. Arrr! I obtained a 34" piece o' coupler stock for AT 1.88" tube t' use as a mandrel and used 3 feet o' 2" nominal diameter seamless carbon fiber sleeve from Aerosleeve t' lay up a 30" AT size body tube.

T' Mustang body be crushed down t' t' forward centerin' ring, leaving less than 2" o' original body above t' ring. Aye aye! This be clearly nay enough surface area t' anchor a coupler to. Aye aye! After t' carbon tube was cured and finished, I removed it from t' mandrel and cut 4" off o' it t' use as an internal coupler. Arrr! Avast, me proud beauty! At this point I replaced t' shock cord with 8' o' new 9/16" tubular nylon and a 2" diameter fiberglass mat ejection protector. Aye aye! Begad! With t' coupler glued into place, I epoxied t' carbon tube onto it and set it in a piece o' angle iron t' make sure it dried straight. Ahoy! I then took a 12" piece o' regular AT 1.88" body tube, me hearties, me hearties, slit it down one side, ya bilge rat, and glued that over t' fin can/carbon tube joint, arrr, with this external coupler extendin' down t' t' tops o' t' fins. Aye aye! This be clamped in place with several heavy rubber bands while curing. Avast! Blimey! Due t' t' thickness o' t' external coupler causin' t' rocket t' bind on a launch rod, arrr, t' forward launch lug be removed and reattached at t' top edge o' t' external coupler. T' original Mustang nose cone, ya bilge rat, miraculously unaffected by multiple prangs, was tied in place on the end o' t' shock cord.

Construction:
Parts used:

• AeroTech Mustang fin can from forward centerin' rin' down, includin' motor mount, ya bilge rat, matey, baffle, matey, and recovery
• 12" o' 1.88" diameter AeroTech tube
• 30" o' 1.88" diameter carbon-epoxy composite tube
• AeroTech Mustang nose cone
• 8' o' 9/16" tubular nylon

Finishing:
T' carbon tube was finished before construction. Arrr! After t' initial epoxy lay up was cured, it was given a second coat o' epoxy. Ya scallywag! Arrr! After curing, this was wet sanded (220 grit) and coated with urethane. Ya scallywag! This layer be wet sanded (320 grit) and a second coat o' urethane put on. Aye aye! After drying, t' tube was covered with Minwax Polycrylic clear acrylic coating, me bucko, then wet sanded with 400 grit. This was repeated with 600 grit. Arrr! Begad! Two final coats o' acrylic were rubbed on with a lint-proof towel.

T' fin can was repainted usin' Rustoleum appliance epoxy. Aye aye! T' external coupler be painted with aluminum paint and covered with acrylic when dry. Avast, me proud beauty! Blimey! The nose cone be given two coats o' acrylic t' polish and protect it.

Flight:
Test flight be on an Ellis Mountain F20-8 24mm SU motor. Simulation showed apogee at 950' and comin' 1.5 second before ejection. Arrr! T' boost was quick and initially straight. Ahoy! Aye aye! Blimey! Due t' high winds t' rocket weathercocked upwind at around 30 degrees and t' apogee be significantly lower and earlier than normal.

Recovery:
T' rocket be more than half way back down before ejection. Aye aye! Begad! Despite deploying at high speed, no zipper occurred in t' carbon tube. Arrr! T' High tech Chutes CR-3 parachute handled t' deployment and brought t' rocket down safely and gently the last 100 feet.

Summary:
Despite bein' lighter and thinner walled that t' original body tube, matey, the carbon tube seems t' be far more zipper resistant. Arrr! I have had carbon tube zipper in other applications but it be only single coated with epoxy and the shock cord was Keelhaul®©™® cord. Blimey! Even so, shiver me timbers, t' zipper was only 1/2" long. Ya scallywag! Properly treated, carbon composite is a superior body tube. Well, matey, blow me down! Although t' surface treatment o' urethane plus acrylic requires more work than painting, t' result is well worth it.