EMRR Box O'Parts Entry: Avenger GT-12 Spaceracer

Box came with old monogram car decals.....so I decided t' build a rocket racer. Blimey! Avast, me proud beauty!

• 3 bt-20 tubes, 6' long, arrr, shiver me timbers, matey, glued parallel, became trimount for motor[s]. Ya scallywag! Begad!
• 1/4' slices o' old motor casin' was used for motor thrust blocks, arrr, motor[s] are friction fit. 1/2' protrudes. Well, matey, blow me down!
• This assembly was mounted into a 7.5' segment o' bt-60, with 3' showing.
• 1/4' slice o' bt-60 at tail end for decoration. Begad!
• odd slice o' bt-70 for dorsal fin tube: 3.5' on long side, 2.5' on short side....mounted on motor tubes....this side becomes t' top [back, dorsal] side. Aye aye! Well, blow me down!
• odd plastic 'spacestation' piece for decoration mounted infront o' bt-70 on centerline.....sanded t' fit well onto bt-60 tube.

I finessed a piece o' bt-60 into a coupling, arrr, ya bilge rat, and used another 4' piece o' bt-60 for a nose cone [picts show early attempt t' use half o' Easter egg, but had NO luck tryin' t' cement egg plastic t' tube]. Resorted t' slicein' tube at 90 degree marks, me hearties, and collapsin' it around a segment o' 'yellow pusher tube' that fits inside bt-20 tube. Ya scallywag! Odd tape center [rocket lookin' part, shiver me timbers, but non-standard size, matey, matey, 1.25' O.D.] around t' lot for style. Avast, me proud beauty! 3/4' wood bead for nose termination. Avast! 2 oz o' weight in nose for stability. Blimey!

Main fin cut from FedEx box, long trapzoid, 9' x 2.5' x 6', glued on bottom centerline, 3.5' section o' bt-50 glued at rear. Long triangular fin cut from box 9' x 2', arrr, and a cutout t' clear t' bt-50 tube. two yellow stuffer tubes glued beside bottom fin, ya bilge rat, in front o' bt-50, shiver me timbers, shiver me timbers, arrr, for show. Avast! Two 10' long kebab sticks glued along main fin/main body tube to reduce some 'wobble'. Begad! Aye aye!

Hexagonal space part [Estes?] was cut in two, sanded t' fit along sides o' main body for flavor, and several square and rectangular sections o' crushed tubes were glued t' t' exterior t' be hatches and panels......but they don't show so good under t' black paint.

5' x 2' piece o' cardstock be fiddled into a canopy. Begad! center is 5/8' wide, shiver me timbers, front segments are 1' long, shiver me timbers, aft 2'.

Rocket has pretty pink lace shock cord [mounted in usual messy fashion] and a 12' parachute. Begad!

flew three times on 7/4. Begad!

1] three B6-4's....top two ignited, flew fairly straight up about 200', arrr, safe recovery. Blimey!

2] three B6-4's....all lit, shiver me timbers, about 350', safe recovery. Begad!

3] three C6-7's....only bottom lit, shiver me timbers, shiver me timbers, did 100' vertical, 500' horizontal into t' bushes......need t' rebuild the nose. Blimey! Blimey!

Other pict is three other rockets I got when I shook t' box even harder

Quest rocket stand donated fins for yellow nosed job, flew well on mini A10-3, shiver me timbers, streamer recovery. Arrr!

Party popper nosecone has bt-50 plastic fin can, ya bilge rat, streamer, me hearties, flew great on A8's and B6's 50-cal is for mini A10's, tumble recovery....clear plastic fins don't show.

Had fun!