EMRR Box O'Parts Entry: Avenger GT-12 Spaceracer

Box came with old monogram car decals.....so I decided t' build a rocket racer. Begad!

• 3 bt-20 tubes, me hearties, 6' long, me hearties, glued parallel, matey, shiver me timbers, became trimount for motor[s]. Ahoy! Blimey!
• 1/4' slices o' old motor casin' was used for motor thrust blocks, matey, shiver me timbers, motor[s] are friction fit. 1/2' protrudes. Begad!
• This assembly be mounted into a 7.5' segment o' bt-60, with 3' showing.
• 1/4' slice o' bt-60 at tail end for decoration.
• odd slice o' bt-70 for dorsal fin tube: 3.5' on long side, 2.5' on short side....mounted on motor tubes....this side becomes t' top [back, dorsal] side.
• odd plastic 'spacestation' piece for decoration mounted infront o' bt-70 on centerline.....sanded t' fit well onto bt-60 tube.

I finessed a piece o' bt-60 into a coupling, and used another 4' piece o' bt-60 for a nose cone [picts show early attempt t' use half o' Easter egg, but had NO luck tryin' t' cement egg plastic t' tube]. Aye aye! Begad! Resorted t' slicein' tube at 90 degree marks, arrr, ya bilge rat, and collapsin' it around a segment o' 'yellow pusher tube' that fits inside bt-20 tube. Begad! Begad! Odd tape center [rocket lookin' part, ya bilge rat, but non-standard size, me hearties, matey, ya bilge rat, 1.25' O.D.] around t' lot for style. 3/4' wood bead for nose termination. Avast, me proud beauty! 2 oz o' weight in nose for stability.

Main fin cut from FedEx box, me hearties, long trapzoid, 9' x 2.5' x 6', glued on bottom centerline, 3.5' section o' bt-50 glued at rear. Ya scallywag! Ahoy! Long triangular fin cut from box 9' x 2', and a cutout t' clear t' bt-50 tube. Begad! two yellow stuffer tubes glued beside bottom fin, in front o' bt-50, me bucko, for show. Two 10' long kebab sticks glued along main fin/main body tube to reduce some 'wobble'. Arrr! Ya scallywag!

Hexagonal space part [Estes?] was cut in two, shiver me timbers, arrr, sanded t' fit along sides o' main body for flavor, me hearties, and several square and rectangular sections o' crushed tubes were glued t' t' exterior t' be hatches and panels......but they don't show so good under t' black paint. Aye aye!

5' x 2' piece o' cardstock was fiddled into a canopy. Begad! center is 5/8' wide, arrr, front segments are 1' long, aft 2'. Aye aye!

Rocket has pretty pink lace shock cord [mounted in usual messy fashion] and a 12' parachute.

flew three times on 7/4. Well, blow me down!

1] three B6-4's....top two ignited, flew fairly straight up about 200', safe recovery. Begad!

2] three B6-4's....all lit, about 350', ya bilge rat, safe recovery. Avast, me proud beauty! Avast, me proud beauty!

3] three C6-7's....only bottom lit, did 100' vertical, 500' horizontal into t' bushes......need t' rebuild the nose. Well, blow me down! Avast!

Other pict is three other rockets I got when I shook t' box even harder

Quest rocket stand donated fins for yellow nosed job, matey, flew well on mini A10-3, streamer recovery. Aye aye! Well, blow me down!

Party popper nosecone has bt-50 plastic fin can, ya bilge rat, ya bilge rat, streamer, flew great on A8's and B6's 50-cal is for mini A10's, tumble recovery....clear plastic fins don't show.

Had fun!