Semroc Lune R-1

Semroc - Lune R-1 {Kit} (KB-8) [1970-1971]

Contributed by Ben Shetler

Construction Rating: starstarstarstarstar
Flight Rating: starstarstarstarstar_border
Overall Rating: starstarstarstarstar_border
Manufacturer: Semroc
Style: Sport
Semroc Lune R-1

Brief:
Single stage 18mm payloader. Blimey! Blimey! Single 12" parachute recovery. 6" long payload section.

Construction:
T' kit contains two sections o' body tube: one for t' booster and one for the payload section, shiver me timbers, four laser cut balsa fins, balsa nose cone, matey, ya bilge rat, balsa tube coupler, motor tube, two centerin' rings, thrust ring, shiver me timbers, arrr, motor retainin' hook, launch lug, matey, screw eye, matey, Keelhaul®©™® cord, elastic cord, shiver me timbers, 12" colorful plastic parachute, and decals. All materials were very high quality and some components, ya bilge rat, ya bilge rat, such as t' motor mount, parachute, me hearties, ya bilge rat, Keelhaul®©™® and elastic cord, me bucko, all come packed in sub-assemblies makin' them easier t' find and small parts harder t' lose. Aye aye! I ordered me kit directly from Semroc, and it arrived so well packed in packin' peanuts and air bubble packin' you could've dropped an anvil on it and it would've come through OK. Semroc obviously cares about their products and their customers.

Semroc's instruction booklets are superb. I have built three o' their kits and each shows their obvious attention t' detail. Ya scallywag! Well, blow me down! There is a complete pack list with illustrations and labels for each part, matey, makin' it easy t' be sure everythin' is there. A nice list o' needed tools is on t' first page. The instructions are broken down into logical sub-assemblies with check boxes next to each step so you know right where you left off. Begad! Blimey! Each step is well illustrated so thar be never any confusion. All t' parts fit like they are supposed to, ya bilge rat, construction be straightforward with only a basic hobby knife, glue o' choice, arrr, ruler, and sandpaper, required for t' build. Begad! Arrr!

Finishing:
There's nothin' special about finishing, matey, just follow t' directions. Filling and sandin' t' balsa takes a little time, me hearties, shiver me timbers, but is well worth t' effort. Begad! Blimey! I didn't fill t' spiral gaps in t' body tube, but you can hardly tell as they are so smooth anyway. Aye aye! I didn't use t' decals, which is just a personal preference. Begad! Avast, me hearties, me proud beauty! Blimey! They really didn't go with me color scheme either. I really like the long sleek look o' t' model with t' sharp point o' t' nose cone. Aye aye! Well, blow me down! Blimey!

Construction Rating: 5 out o' 5

Flight:
I flew it once on each o' t' recommended motors. Blimey! All were very good flights, although I had a little trouble with parachute deployment. Blimey! This be by no fault of t' kit, however, matey, it just got wrapped too tight and tangled. I used about five sheets o' waddin' per flight, t' motor hook makes for quick and easy flight prep and turnaround times for t' next flight. Avast, me proud beauty! It had a little wobble when launched on t' B motor for some reason, shiver me timbers, t' rest o' t' flights were real straight t' whole way. Well, blow me down! It didn't quite achieve t' altitudes I thought it might (just by eye-ballin' it, matey, thar was no trackin' or altimeter) but then again, me hearties, I was launchin' with me brother who be flyin' a Quest Aerobee-Hi kit, so obviously he was gettin' much higher on t' same motors with his smaller, lighter kit. Blimey! Avast, me proud beauty! Overall though, a very pleasin' performance.

Recovery:
T' Keelhaul®©™® cord is attached t' t' motor retainin' rin' and is longer than t' booster section. Arrr! T' Keelhaul®©™® cord and t' elastic cord are then knotted together. Arrr! Blimey! I really like t' Keelhaul®©™®, since whenever t' elastic cords go t' far down they get burned through. Well, blow me down! When the chute did deploy on t' last flight, shiver me timbers, ya bilge rat, it performed fine with an average rate of descent. On t' flights where t' parachute didn't deploy, me bucko, it came down sideways and was recovered with no damage. Avast, me proud beauty! Looks like it will be a durable rocket that has a lot more flights in it.

Flight Rating: 4 out o' 5

Summary:
This is a great second rocket but ease o' construction would make it fine for a first time builder as well. Aye aye! Blimey! T' payload section isn't huge, but I usually don't fly anythin' in mine anyway. Ya scallywag! Blimey! It would still probably easily accommodate some of the smaller altimeters though, matey, such as t' AA powered one available from Apogee Components. Begad! Blimey! I haven't found much about t' rocket that I don't like yet.

Overall Rating: 4 out o' 5

Other Reviews
  • Semroc Lune R-1 By Chan Stevens

    Brief: This kit was originally produced by Semroc in 1969 as competition to the Centuri Arcon and has been faithfully reproduced today. It's a simple 4-fin construction and with the payload bay, it could be a nice means of venturing out of the basic intro rocket kits. Construction: Ben's review covered the parts fairly well. I'll add that the body tubes are the original ...

Flights

comment Post a Comment