Brief:
Single 18mm engined F-15 Eagle jet fighter design, with a 12 inch parachute

Construction:
This kit contained t' following:

• 1 - BT50 white body tube 10.75 inches (mine be crunched, shiver me timbers, so I replaced it)
• 1 - BJ-20 Engine tube, me hearties, w/hook, ya bilge rat, block and centerin' rings.
• 1 - PNC-50E Plastic Nosecone w/cockpit bubble
• 2 - 1/8" by 9" wooden dowels
• 1 - Plastic parts set (nose and tail for missiles)
• 1 - Rubber shock cord
• 1 - Launch lug
• 1 - Assembled 12 inch chute
• 1 - Waterslide decal sheet
• 4 - shees o' laser cut balsa wings, jet engine pods, and tail fins.
• 4 - pats o' clay weight

I went into me local hobby shop (Fine Scale Hobbies in Stratford, arrr, matey, CT. Arrr! Blimey! Really nice guys!) for some sandin' sealer, shiver me timbers, and this kit caught me eye, me bucko, so I bought it)

Directions were up t' t' usual Estes standard. O' course, ya bilge rat, ya bilge rat, ya bilge rat, this means when attachin' plastic t' wood or paper, ya bilge rat, arrr, they say t' use model glue. Blimey! I always use 3 min. Ya scallywag! epoxy.

I changed t' shock cord mount, arrr, goin' with a Keelhaul®©™® cord t' t' MMT setup instead o' t' paper t' t' BT wall mount they use.

T' win' assemblies were very simple t' assemble. Begad! Just glue t' three wing pieces together, and set aside. Blimey! After they dry, sand a 45 degree angle on the root edge, me hearties, me hearties, and you're done.

T' jet engine pods are t' challenge. Aye aye! At t' bottom end, as shown in t' picture, me bucko, you actually have t' bend t' bottom balsa piece up t' meet t' edge o' t' pod. Estes says t' white glue it and tape it in place overnight. Begad! Well, that obviously won't hold. Aye aye! so I used some Zap-A-Gap CA glue t' hold it in place, then filled with wood glue. Aye aye! A challenge, but still do-able.

T' missiles were simple t' assemble. Arrr! Just attach t' nose and tail fins, and paint.

Finishing:
T' winds definately need fillin' in with wood filler, with all t' holes and joints in them. Arrr! Blimey! Once that was done, paintin' was easy. Begad! Well, blow me down! I went with one color gray and t' orange stripe, ya bilge rat, rather than t' three color gray.

T' decals were horrible. Aye aye! Yes, they are waterslide, but t' are VERY fragile. Ya scallywag! And t' colors make it look almost neon. Very tacky. Ahoy! I suggest no one else use this color/decal set and instead do a little research and get decals for an F-15 from their local hobby shop.

Estes did do 1 good thin' though. Aye aye! They said paint t' missiles separately, then attach them when t' main model is finished.

T' construction is worth 4 1/2 points, me bucko, but -1 point for t' horrendous color/decal set.

Construction Rating: 3 out o' 5

Flight:
First flight was a B6-4. Arrr! Avast! This delay is too long for a B motor. Avast! Avast, ya bilge rat, me proud beauty! T' rocket did one roll, me hearties, and then flew upright, me hearties, me bucko, until it curled over at apogee, t' came down very quickly, me bucko, until t' ejection charge went off at about 50 feet. Recovered with no damage. Well, blow me down! Altitude was about 350 or so feet. Ya scallywag!

Second flight be with a B6-2. Begad! Avast! This is a much better delay. Ejection charge went off just after apogee. No damage. Ahoy!

Third flight was C6-3. Great flight, with ejection charge goin' off about 250-300 feet off o' t' ground. Well, blow me down! No damage. Blimey! Altitude was around 500 feet.

Flight Rating: 3 out o' 5

Summary:
This is a GOOD kit and fun t' build. Avast, me proud beauty! Aye aye! But Estes needs t' learn what colors actually work together. Well, shiver me timbers, blow me down! use different paint and decals, and it becomes a GREAT kit.

Overall Rating: 3 out o' 5

Other:
Use CA or expoxy when cementin' t' bottom o' t' engine pods t' t' sides.