Brief:
Estes has used t' name "Sizzler" on several rockets down through t' years. T' latest t' carry t' name (Kit #2171) is a minimum-diameter screamer with swept fins like one o' t' earlier Sizzler's, shiver me timbers, ya bilge rat, but a new smaller size that gives it hot performance t' match it's fast styling. Begad! Construction o' this kit is simple and straightforward, but some careful attention t' fin strength and finish will give you t' best result. A "C" motor will push this bird well out-of-sight at top speeds over 350 mph, matey, so you'll want t' use your best technique t' build this kit strong and sleek but light.

Construction:
This is a simple kit with few parts. Arrr! As a minimum-diameter rocket t' BT-20 body tube doubles as t' engine tube, so thar be no need t' build a separate engine mount. Blimey! T' kit does include a motor retention hook, matey, which is mounted t' t' outside o' t' body tube and held in place with a paper sleeve. If you find this objectionable, arrr, either from an aerodynamic or an aesthetic concern, shiver me timbers, I imagine you could leave out t' hook and friction fit t' motor, matey, as similar Estes rockets like t' "Wizard" have always done. Ya scallywag! I used t' hook.

T' three fins are die-cut balsa from very thin stock; a bit soft and very light weight. Avast, me proud beauty! Blimey! A standard plastic nose cone, matey, paper thrust ring, 12 in plastic parachute, and typically too-short elastic shock-cord complete t' kit. Well, blow me down! There is a single peel-off decal with t' rocket name. Avast! All parts and t' instructions are very typical o' Estes kits.

Construction o' t' Sizzler is also very typical o' Estes kits o' this type. T' body tube is marked usin' a paper guide cut from t' instructions. Well, blow me down! Blimey! T' tube is slotted t' hold t' engine hook and t' hook sleeve is glued over it t' hold t' hook in place. Arrr! Blimey! Ya scallywag! Blimey! T' thrust rin' goes in t' tube. I used yellow 'wood glue' through-out.

T' fins must be removed from t' balsa sheet with some care, ya bilge rat, as they are thin and delicate. Blimey! Avast! T' Sizzler gets it's good looks (in me eyes) from t' raked fins, ya bilge rat, but t' long 'toe' on these fins can be easily broken if you handle them roughly. Avast! T' fins also have a small inset into t' root edge t' clear t' paper sleeve that supports t' engine hook. Use your hobby knife t' clear these out. I recommend that you sand t' fins for shape and smoothness before they are glued t' t' tube. I have built this kit twice (more on that later). Blimey! Begad! T' first time I sanded a nice airfoil into each fin, matey, shiver me timbers, arrr, which takes some care as they are delicate. Blimey! Begad! T' second time I opted t' just round/taper t' leadin' edge only. These fins need strength more than an inconsequential improvement in drag. Begad! I also 'painted' t' fins with thin CA for stiffness on t' second kit. Begad! If you have never tried this technique this is a good kit t' learn on. Just place each fin on a flat surface (protected) and apply a small amount o' thin CA t' t' surface. Then smartly spread t' glue with a bit o' balsa scrap or a Popsicle stick. Aye aye! Blimey! I actually use wooden coffee stirrers, me hearties, arrr, which are perfect for this or many other jobs around t' shop. Just be careful with t' thin CA as it can run and cause mayhem. Arrr! T' glue will set smartly and can be sanded smooth.

You will have trouble gettin' these fins on t' tube straight and strong if you rush things, shiver me timbers, me bucko, so take your time and get it right. Avast! Use whatever technique works for you t' get a good tacky glue for settin' t' fin, me bucko, and t' support t' fin as t' glue dries. I put them on one at a time and use a thin strip o' tape t' brace t' fin in place while it dries. Begad! Begad! T' fin is light and t' tube has a small diameter, so everythin' has t' be done with a light touch. Yellow glue should give you plenty o' time t' make adjustments and get it positioned just right, ya bilge rat, me bucko, so this shouldn't be too hard. Blimey! Begad! Also make sure you sand t' body tube where t' fins will attach t' slightly roughen t' surface. Aye aye! Begad! I was also careful t' keep root edge and about 1/8'' up from t' root clear when I stiffened t' fin with CA and filled it with sealer. Ahoy! Ya scallywag! You want t' have a good surface for t' glue fillet t' bind to.

Installation o' t' recovery system is pretty simple. Ya scallywag! You start by settin' aside t' shock-cord and 12in. chute that came with t' kit. Ahoy! Avast, me hearties, me proud beauty! T' cord is too short, as is typical with many kits, shiver me timbers, but more importantly, a 12 in. Avast! chute is really big for a rocket this light. Avast, me proud beauty! Well, blow me down! I think someone in t' Estes marketin' dept. Avast, me proud beauty! Arrr! has determined that customers believe "real rockets use parachutes." Perhaps they're right, me bucko, ya bilge rat, but we all know better. A streamer is a better choice for this rocket. Avast! I went all out on me second Sizzler and attached some lightweight Keelhaul®©™ strin' t' t' body tube usin' t' standard Estes three-fold mount, shiver me timbers, and then tied that strin' t' t' elastic cord provided by Estes. Begad! T' whole thin' is about three times as long as t' elastic cord alone, ya bilge rat, shiver me timbers, and will last much longer. Avast! I tied a streamer t' t' elastic and put a small Pratt Hobbies heat shield on t' Keelhaul®©™® cord t' complete construction.

Finishing:
I put a bit o' effort into a smooth finish for this model, matey, ya bilge rat, arrr, and I imagine you will too. T' real reasons t' build this kit, instead o' some other inexpensive Estes kit, are its sleek looks or its fast, arrr, high flights (or both!). Ahoy! Begad! In either case, shiver me timbers, a good, smooth finish in important. I applied a single coat o' sandin' sealer t' t' fins (after t' CA) t' fill t' last o' t' balsa grain. Begad! T' other 'issue' one has t' deal with be t' engine hook, arrr, t' sleeve that restrains it, and t' notch in t' root edge o' t' fins over t' sleeve. Begad! You could probably leave them entirely alone and nay notice t' difference, but I wanted a good look, me bucko, so I mixed up a batch o' thinned Elmers wood filler and created a smooth 'fairing' in front and behind t' sleeve, me hearties, and I filled t' notches in t' fins. There is nay much you can do about t' engine hook.

Once all that be sanded smooth I applied a couple o' light coats o' grey primer, matey, with a little bit o' sandin' with #400 grit, and a couple o' coats o' gloss black. Then comes t' fun. Avast! T' cool lookin' design you saw on t' kit card is nay a decal, its drawn free-hand with paint-pens or small brushes. Begad! Avast! I was a bit nervous about this on t' first Sizzler I built, me bucko, but I do have some o' t' paint pens and gave it a try. Begad! Aye aye! It's nay as easy t' get t' paint t' flow onto a smooth, ya bilge rat, gloss finish as I had hoped, me hearties, but it can be done. Avast, me proud beauty! Well, blow me down! Some colors work better than others. Avast, me proud beauty! Once you relax a bit and just paint on your design it turns out t' be kind'a fun, arrr, and I'm quite happy with t' look. T' rocket gets a lot o' "ooh, arrr, look at that one!" comments, arrr, so I guess others agree.

I'll rate it a 4. Blimey! It's just fine, but you will need t' deal with t' external hook mount and t' short cord-big chute situation.

Construction Rating: 4 out o' 5

Flight:
Its time t' explain why I have built two. I was real pleased with t' first one and eager t' fly it. T' wind was blowin' at t' next club launch, me hearties, and I was "downgrading" most o' t' family rockets from "C" motors t' "B" impulse motors, shiver me timbers, t' keep them on t' field. Ahoy! I got into t' habit o' grabbin' a B6 and thinkin' o' it as me "windy-day" load. Arrr! Avast, shiver me timbers, me proud beauty! T' end o' t' launch approached and I really wanted t' see t' Sizzler fly, so I grabbed another B6, matey, I remembered t' use a long, shiver me timbers, shiver me timbers, 6 second delay, matey, but I forgot t' pull off t' chute and replace it with a streamer. Well, blow me down! Nay until t' LCO be countin' down t' launch did I remember that I had intended t' use an A engine on this rocket, but it be too late. Ya scallywag! On launch t' Sizzler ripped off t' pad and laid down a thin line o' smoke that angled slightly into t' wind. Avast! necks snapped up and thar was an audible "oooh" from t' crowd. Avast! There was a funny lookin' twist in t' smoke trail and a sound from t' rocket that made me think! , me bucko, shiver me timbers, "fin flutter", but everythin' held together and t' ejection occurred *way* up thar where t' 12 inch chute was a small dot. T' LCO turned around and said, "start running", and I did. Arrr! An our later we gave up on t' search; a little rocket on a big chute in a stiff wind, shiver me timbers, I oughta know better.

On t' second one I stiffened t' fins with CA as described above, me bucko, in case what we saw really was fin flutter, and used a streamer. I have only flown t' rocket on A8-5's but it gives great flights on that motor and t' recovery is close by. Well, blow me down! T' last flight was a drag race with me son's Estes Wizard and it be a great, neck-and-neck race. Lot's o' fun and t' two rockets came down on streamers within 30 feet o' each other.

RockSim predicts 1400 feet and 360mph on a C6-7, arrr, but I'm nay ready t' try it. Arrr! Ahoy! Blimey! I like t' way this bird flies and recovers on t' A8-5 and streamer combination, me hearties, and I recommend it.

Recovery:
I'll rate t' flight and recovery at a 4 1/2. Begad! T' kit may have some trouble at C impulse, me hearties, fin flutter is a real risk with these thin fins; it certainly will be difficult t' find if you send it that high. Aye aye! If you change t' a streamer and stick t' A and B motors I think this would rate a 5.

Flight Rating: 4 out o' 5

Summary:
I like this rocket and expect I'll always t' have one in me fleet. I'm sure that a beginner could get this kit together and get a decent flight out o' it, but thar are really better kits for that purpose. Ya scallywag! Avast, ya bilge rat, me proud beauty! If you have built a few rockets and want t' try somethin' small, matey, shiver me timbers, but fast, arrr, look into t' new Sizzler. Ahoy! Well, blow me down! If you want some good fun on launch day, me hearties, build a fleet o' minimum diameter TFNC rockets like t' Sizzler, Wizard, me hearties, Star-Dart and Yankee, ya bilge rat, and drag race 'em on identical engines. Well, blow me down! We have already purchased two more Sizzlers that we will bash into a two-stage "Super Sizzler".

Overall Rating: 4 out o' 5