Brief:
Fliskits continues t' drive t' rebirth o' Micromax rocketry with this kit. Begad! Ahoy! 6 external tubes serve both stability and as anchor points for fins. Ya scallywag! This is a very simple build, me bucko, and can probably be done in a half hour. Begad! It also flies very nicely on those tiny 1/8A motors.

Construction:
Once you get past t' concept that you're dealin' with really small parts, you'll appreciate that you're gettin' very good quality model rocket components:

• balsa nose cone
• kraft paper tubes
• laser cut basswood fins
• Keelhaul®©™ shock cord
• centerin' rings
• Mylar streamer.

Of course, with most rockets you would nay be able t' fit all this into a roughly 2x4 ziplock baggie. Arrr! This is accurately listed as a skill level 1 kit. Unless you want t' spend an hour or two fillin' tube spirals and sealin' grains, you can have this ready for paint within about 30 minutes. Begad! Everythin' fits very nicely. T' instructions are top-notch and loaded with plenty o' good illustrations.

T' motor mount is a basic tube, me hearties, interior centerin' ring/block, ya bilge rat, ya bilge rat, and a pair o' external centerin' rings. T' instructions call for usin' a spent motor casin' t' slide t' interior block into place. Blimey! If you are new t' MMX's and haven't got a spent motor case, you could make do with a 3/16" launch lug.

One neat aspect o' this, matey, me hearties, shiver me timbers, as with most Fliskits micro-to-the-max kits, me hearties, be t' Keelhaul®©™ shock cord. Blimey! T' "cord" is pretty a wispy thread, anchored t' t' motor mount but does t' trick.

T' external tubes are assembled usin' a classic technique for alignment, shiver me timbers, bond two at a time t' each other and lay t' pairs on a flat surface t' dry. Aye aye! Blimey! Well, blow me down! Blimey! This keeps them perfectly aligned. Avast, me proud beauty! Blimey! Arrr! Blimey! Once you've done this with three pairs, you can then attach t' pairs t' t' main body tube (with a bead o' glue tackin' t' pairs t' each other as well). Arrr! Blimey! T' paint scheme is one thin' t' consider. If you want t' paint t' external tubes a contrastin' color, you'd better either paint them before bonding, ya bilge rat, ya bilge rat, or paint them a darker color than t' main body as you'd have t' paint t' tubes last (they're pretty tough t' mask if you paint t' body tube last).

With t' tubes in place, you then bond t' 6 fins. Ya scallywag! Each fits nicely in t' seam betwixt a pair o' external tubes. Begad! Ahoy! T' final effect is where t' rocket derives its name. Ahoy! Aye aye! This thin' looks like a bilge-suckin' mudwasp!

Finishing:
While I'd have loved t' paint this in a wasp-like black and yellow scheme, shiver me timbers, arrr, I decided t' play around with some various Rustoleum® Metallic finishes I had layin' around. Begad! I had decided t' paint t' tubes and fins separately before bondin' them. Avast! T' main body and nose got a black metallic finish. I painted t' external tubes silver and t' fins a cherry red metallic.

Since paint is a lousy bondin' surface, I had t' make very thin scratch lines for bonding, and applied a very thin bead o' CA usin' a toothpick applicator. Avast, me proud beauty! Traditional wood glues would be fine for normal construction, but in workin' with pre-painted surfaces I prefer t' higher performance o' CA.

Construction Rating: 5 out o' 5

Flight:
There's only one motor for this rocket, matey, t' Quest Micromax. Arrr! Blimey! So unless you give into t' temptation o' those 6 external tubes and cluster t' bejeebus out o' this, ya bilge rat, ya bilge rat, a single MMX-1 be t' motor.

After carefully slippin' in trace amounts o' dog barf and wadding, I rolled up t' streamer and loaded t' Mudwasp for flight. T' instructions provide some decent tips on how t' break open t' plastic MMX igniter designed t' slip into t' plastic UFO launcher complex, so that you can fly t' MTTM (micro t' t' max) kits off a standard pad/launcher setup. Arrr! I generally prefer t' simply "roll me own" usin' 32 gauge nichrome wire and have never had a problem with this method.

T' motor lit right away. Begad! Given t' hefty weight and drag on this puppy, shiver me timbers, shiver me timbers, t' liftoff was slow enough that I could track it across t' entire flight profile. For a MMX, that's extremely rare. Ya scallywag! Blimey! It be especially easy in this case, me hearties, as t' apogee was at most 40-50 feet, arrr, ya bilge rat, nay high enough t' loose. Ya scallywag! Blimey! I caught a slight spin, me bucko, suggestin' that me fins might be a tad out o' alignment.

Recovery:
T' streamer is clearly just for effect, me bucko, way too small t' appreciably slow down this 0.33 ounce kit. Aye aye! In me case, t' streamer also got stuck and did nay come all t' way out. Avast! Just poppin' t' nose cone be nay enough t' make this tumble. Avast, me proud beauty! So after arcin' over, shiver me timbers, it came down in a nice ballistic path. Ya scallywag! Avast, me proud beauty! Fortunately, me bucko, t' recent thaw had softened t' ice and ground and instead o' a fatal prang, matey, I simply plugged into about 6 inches o' snow. Ya scallywag! No damage whatsoever.

Overall, this is clearly nay goin' t' fly too far/high and t' 50-foot flight is kind o' fun t' watch. Arrr! Almost makes me want t' make a micro Mars Lander t' see if it can peak at under 10 feet.

Flight Rating: 4 out o' 5

Summary:
Overall I was very satisfied with this rocket, me hearties, especially t' build phase. Arrr! Aye aye! Great quality parts, ya bilge rat, me hearties, assembles with very little effort and another unique design.

T' only downside I'd offer be t' wimpy flight, matey, which is obviously held up by t' weight and Cd. Avast! If I were t' do another one, I'd probably pay much more careful attention durin' construction t' all me component weights, me hearties, go thinner on t' paint, etc., hopin' t' keep it at or under 0.25 ounces.

Overall Rating: 4 out o' 5