Brief:
At me last launch, someone stepped on me Estes Porta-Pad and snapped t' legs right off o' it. Well, ya bilge rat, blow me down! I needed a new pad and one that would hold up because I wasn't in t' mood t' go buy a new pad for $40. Avast! I decided t' build me own out o' PVC pipe from Home Depot. Arrr! It be built for about $10 and can hold model and mid power rockets with a 1/8", 3/16", arrr, arrr, or 1/4" launch lug.

Construction:
This is was a very simple build. Well, me bucko, blow me down! If you know how t' use a hack saw and PVC cement, arrr, shiver me timbers, me bucko, it is easy. I bought all o' t' PVC at Home Depot. Blimey! First, me bucko, arrr, me hearties, I found a 3/4"x10' section o' piping. Arrr! Next, I went t' find all t' little plastic parts t' make it look nice. Ya scallywag! I found four 3/4" end caps and a four way cross piece. Aye aye! Ahoy! T' final pieces were four 45 degree elbows for 3/4" tube. I already had all o' t' tools and supplies needed (1/8" drill bit, me bucko, 3/16" drill bit, arrr, 1/4" drill bit, me hearties, PVC cement, shiver me timbers, and a hack saw) at home.

T' first step was t' cut t' PVC pipe into 4 legs that should each be 20" long. Avast, me proud beauty! Arrr! I then used PVC cement t' bond t' end caps t' t' legs. Well, blow me down! Next I cut four 2" long struts and glued them into t' center piece. Blimey! Arrr! I clamped t' center piece down and drilled t' holes for t' launch rods evenly spaced along t' center piece. Ya scallywag! Blimey! T' 1/4" hole was drilled in t' center so that t' pad would hold t' weight more evenly on me larger rockets across all four legs and nay be off balance. Aye aye! T' 1/8" hole and 3/16" hole are drilled 1/2" away from t' 1/4" hole. Avast, me proud beauty! I made sure that t' 2" struts are glued all t' way into t' center piece before drillin' because t' smaller holes will go through them. Ahoy! Aye aye! T' finish t' legs, I glued t' 45 degree elbows t' t' top o' each leg. Begad! Arrr! DO NOT glue t' legs t' t' center piece, shiver me timbers, as this will allow them t' pivot on t' struts t' aim rockets into t' wind. Well, blow me down! Avast, me proud beauty! I chose nay t' paint mine.

Flight:
This pad handles model/mid power rockets without a problem. I used it for t' first time at me October launch at t' local school. Ya scallywag! I put in me 1/8" rod and slid t' leftover blast deflector plate me Estes Port-Pad over t' rod. Arrr! Arrr! I launched an Estes X-Flyer off it. Avast! Begad! T' pad works! After many small rockets I put in t' 3/16" launch rod. I launched me scratchbuilt USA Gymnastics rocket off it on a D12-3 and an Estes Blue Ninja on a C11-3. Avast, me proud beauty! Finally, me hearties, ya bilge rat, I put in t' 1/4" rod and launched me Dynastar Orion, me hearties, Estes Executioner, arrr, and LOC/Precision Onyx. Begad! T' pad worked great, even for t' almost 1 pound Onyx.

Summary:
Anyone in need o' a cheap but durable launch pad can build this pad in under an hour, so it is great if you happen t' break your pad t' day before a launch.