Brief:
I be provided with me Mark 305 for beta testing. Begad! As t' name implies, this is a “super” upscale o' t' old Estes Mark. Aye aye! Although t' interchangeable motor mount included in t' kit is designed for a single 24mm motor, me bucko, you can get additional motor mounts that provide a variety o' options for clusters or bigger motors dependin' upon t' weight you add t' t' nose. Begad! A spacer is included in t' interchangeable motor mount kit t' allow t' use o' either Estes D or E motors, ya bilge rat, and t' rocket recovers on a very nice 24-inch rip-stop nylon parachute. Ahoy! T' rocket is over 28 inches tall and weighs 8.6 ounces with standard completion.

Construction:
T' main body tube is a big 2.34 inches in diameter and is slotted for t' three fins, which are laser cut basswood. Very nice! T' big balsa nose cone was top quality as well and very smooth. Arrr! T' 24mm motor mount has a unique rotating design that locks it in for flight and can then be rotated out t' interchange with a different motor mount. Begad! Begad! The centerin' rings are laser-cut light-ply and a 3.75” engine hook is provided for motor retention. A CR2050 kraft rin' is used for t' thrust ring. Avast, me proud beauty! A Keelhaul®©™®/3/8” elastic shock cord combo is included along with two big launch lugs, arrr, one 3/16” and t' other 1/4”, and a hefty eye screw. A baffle assembly is included which uses offset tubes attached t' centerin' rings, and it actually works! Trim Monokote is provided for applyin' t' black stripes on t' model.

T' professional look o' a Hawks Hobby kit and t' quality o' parts has always been superb, me hearties, but now I think the quality o' t' instructions has caught up. T' pages were all stapled together which is a big plus in me book, ya bilge rat, arrr, plus the text aligned well on t' pages and t' accompanyin' illustrations were very clear and plentiful. I modified the construction o' t' motor mount t' allow installation o' t' engine hook usin' me standard method. Blimey! Begad! Here’s the link on EMRR’s tip page for the general idea.

This method allows positive motor retention while nay havin' t' worry about t' hook gettin' in t' way o' the delay element when usin' t' AeroTech reload motors. It aligned perfectly with t' upper centerin' rin' so no real modifications were required, and it didn't interfere with t' “lock” design. I used a Dremel t' trim the upper end o' t' motor hook t' be level with t' top edge o' t' centerin' ring. Avast, me proud beauty! T' instructions indicate t' attach the Keelhaul®©™® cord by wrappin' it around one o' t' baffle tubes and insertin' t' end through a small hole in t' upper centering ring, arrr, and then attachin' t' elastic cord t' a loop at t' end. Begad! Aye aye! However, shiver me timbers, me hearties, I used me standard tri-fold shock cord attachment t' allow inspection o' t' shock cord although t' baffle makes that almost unnecessary with this kit. Begad! To minimize abrasion from t' Keelhaul®©™® against t' body tube, arrr, I soaked in CA around t' top 1/2" o' t' body tube and tied a knot in t' Keelhaul®©™® to meet t' lip o' t' body tube.

T' fins attached very nicely t' t' rocket, me bucko, ya bilge rat, alignin' perfectly with t' slots in t' tube. Ahoy! After makin' sure the fin was aligned properly, I applied a small amount o' CA at each end t' hold it in place before movin' on t' t' next fin. Aye aye! Since t' centerin' rings are slotted t' slide up t' tabs on t' fins I smoothed in JB Weld for t' fillets, as I didn't want t' worry about epoxy drainin' down onto t' tabs and interferin' with t' insertion o' t' motor mount. Glue on t' launch lug, shiver me timbers, matey, install t' screw eye into t' nose cone (addin' weight first t' compensate for t' largest motor you plan t' fly), matey, and attach t' shock cord and you’re almost done. T' launch lug is glued on next t' and at t' top o' one o' t' fins. Avast, me proud beauty! I decided t' use t' 3/16” size and save t' 1/4” for somethin' more heavy duty. T' parachute be already assembled and had small grommets holdin' t' shroud lines; it's a very nice parachute.

Finishing:
T' balsa nose cone required very little finishing. Avast, me proud beauty! With only a very light coat o' Elmer's Light Fill ‘n' Finish, ya bilge rat, t' nose cone was very smooth. Only a light coat o' filler was also needed on t' fins as t' basswood be very smooth after sandin' with 400 grit sandpaper. Avast! T' body tube was t' only thin' that required any significant effort-–darn spirals! After usin' Fill ‘n' Finish t' fill those and much sanding, I sprayed t' entire model with a light coat o' Kilz t' seal off t' glue and provide a solid base coat. Avast! Next, I lightly sanded t' entire model with 240 grit sandpaper and then sprayed on a coat o' primer. Begad! Next, me hearties, ya bilge rat, sand and primer, and sand and primer again, shiver me timbers, sanding with 400-grit sandpaper. I painted t' entire model with Valspar’s Restoration Series Allis-Chalmers orange and after dryin' for a couple o' days applied t' Monokote trim. Wow! Even me wife was impressed. Avast, me proud beauty! Avast, ya bilge rat, me proud beauty! She said, matey, me hearties, “That one looks like a real rocket.” I put a thick coat o' Future Floor Finish on t' painted surfaces t' protect everything.

Construction Rating: 5 out o' 5

Flight and Recovery:
First flight was on an Estes E9-4 with t' wind speed steady at about 5-8 mph. Avast! Blimey! I didn't put any waddin' in it and there be only a slight ejection residue noticeable on t' parachute after recovery. Aye aye! Blimey! T' flight was perfect although ejection was a little early so I decided t' use a six second delay on t' next flight. Unfortunately, arrr, arrr, t' wind speeds had increased t' betwixt 8-12 mph with occasional strong gusts. Avast! Blimey! Ya scallywag! Blimey! A gust o' wind caught t' big fins a few feet off the launch rod sendin' t' rocket up about 40 degrees from vertical. T' model was already headed down ballistic when the nose cone ejected, rippin' t' shock cord out and pullin' three o' t' grommets out o' t' parachute. Begad! Blimey! Avast, me bucko, me proud beauty! Blimey! T' body tube caught t' nose cone, slicin' a huge chunk out o' it, and t' shock from t' impact o' t' tube into t' ground shattered t' centerin' rings, probably because o' a slight play in t' fit o' t' centerin' rings. Begad! Blimey! Fortunately, shiver me timbers, the ground was still soft enough that t' body tube be undamaged. She’ll be ready t' fly again as soon as I repair the nose cone and parachute and add new centerin' rings on t' motor mount.

Flight Rating: 5 out o' 5

Summary:
T' Mark 305 is a fantastic rocket. T' kit is very easy t' build and t' interchangeable motor mount provides the modeler with a variety o' motor options. Begad! T' large fins do mean you’ll need t' fly it in lower winds unless a motor with a higher initial impulse is used. Ya scallywag! T' 24 inch rip-stop nylon chute is perfect for recovery, shiver me timbers, and I love the fact that I don't have t' use recovery wadding!

Overall Rating: 5 out o' 5