Brief:
I shortened t' body tube t' t' Goonybird standard 5" (BT-60R) and switched from 13mm power t' 18mm power.

Modifications:
T' main body tube from t' Baby Bertha could be left as is for this project, if you're nay a man who is serious about his Goonies. Ya scallywag! Avast! I chose t' keep things proportional and shortened t' body tube t' t' Goony-traditional 5", matey, a feat I accomplished by wrappin' a nice, me hearties, straight line o' maskin' tape around t' tube then runnin' a hobby cutlass along t' tape until t' blade eventually cut through. Well, blow me down! If you're plannin' on usin' t' 18mm motor mount, shiver me timbers, matey, then this leaves little room in t' body tube for recovery equipment. Aye aye! However, me hearties, t' resultin' rocket is light enough t' employ nose blow recovery. Avast! I initially planned t' use a small chute and cut away a section o' t' nose cone so that I could tuck it up inside. Aye aye! Arrr! This method was a failure, which led t' t' nose blow experience, but steps could easily be taken t' make t' chute or streamer deploy more reliably.

Construction:
T' parts list:

• 1 Estes Baby Bertha kit
• 3/32" balsa fin stock
• 1/8" sewin' elastic shock cord (24")
• 24" Keelhaul®©™® shock cord

Finishing:
Finishin' wasn't all that bad once I figured out t' masking. Ya scallywag! T' get t' giant tongue effect, ya bilge rat, it is necessary t' mask t' rocket after applyin' t' red. Ya scallywag! However, ya bilge rat, arrr, t' contours o' t' mask need t' follow t' curve o' t' "teeth" stickers. I first painted t' rocket red usin' Valspar Cherry Gloss. Well, blow me down! Ahoy! After t' red had cured, I printed off a scan o' t' stickers on a sheet o' regular paper, cut t' "teeth" pattern out, shiver me timbers, arrr, me hearties, and wrapped it around t' rocket in t' spot where I planned t' put t' actual sticker when I printed it. I used maskin' tape t' cover everythin' that needed t' remain red, then sprayed t' aft o' t' rocket with Valspar gloss black. I printed t' stickers on label paper and after cuttin' them out, arrr, they fit perfectly. Ahoy! Avast, me proud beauty! Except for t' fact that I left off some o' t' smaller stickers, me bucko, you'd be hard pressed t' tell me faux-Goony from a real one.

Flight:
With t' 18mm power, Goonies can be funny in flight. Arrr! (Funny as in unstable, me bucko, nay funny like Les Nesman watchin' turkeys come out o' a helicopter.) With some o' t' designs, nose weight is necessary, ya bilge rat, but t' Sky Shriek has enough fin area t' make balance things out. Well, blow me down! I used a B6-4 for t' first flight and it be pretty much as you'd expect t' flight o' a relatively small, draggy rocket on a B6-4 t' be. Arrr! Second flight be on a C6-5 and while it didn't go out o' sight, it be a pretty tiny dot in t' sky when t' ejection charge fired. Ya scallywag! T' weathercock be also fairly extreme, but this be t' be expected due t' t' amount o' fin area versus t' amount o' wind we had on this particular Sunday.

Recovery:
Recovery be iffy at best but as it turned out, me bucko, it didn't matter all that much. Blimey! Cuttin' t' body tube back t' "Goony-stock" length leaves very little room for recovery materials so I improvised. Blimey! Before t' first flight, I cut away all o' t' plastic that wasn't needed in t' base o' t' nose cone and used t' resultin' space t' store t' 8" parachute. Avast, me proud beauty! When t' ejection charge fired, t' chute stayed stuck in t' compartment and t' rocket fell gently t' earth anyway. Avast, me proud beauty! Avast, arrr, me proud beauty! Since it had worked so well t' first time, ya bilge rat, shiver me timbers, I chose t' go t' same route for t' C6-5 flight with similar results. I can't say that I'd consider goin' without a chute or streamer if I be flyin' near asphalt or hard-baked earth, but t' fields were green and weed choked in early April and t' only hard landin' around would have been t' path. Ya scallywag! I've hit that often enough under chute t' know that you still wind up with road rash.

Summary:
PROS:

1. Hey, it's a Goony.
2. Improved performance with 18mm engines.

CONS:

1. Lack o' room for a recovery system.