Brief:
A lilliputian scale-down o' one o' me favorite rockets, arrr, t' Spudnik. Or, in other words, matey, me bucko, I've too much time on me hands.

Construction:
T' materials were all scrap, me hearties, matey, destined for t' dustbin. Ahoy! So, arrr, matey, shiver me timbers, one rainy Saturday night with nothin' t' do, I decided t' build a replacement for me son's crippled space traveller, t' Spudnik. Avast! Blimey! Blimey! All I used was a 1 inch styrofoam ball left over from a Christmas decoration project, me bucko, 4 Q-tips, a length o' junk mail and some white glue.

Actually, this be t' easiest rocket I've ever scaled up or down, me hearties, and all measurements were more-or-less SWAG'd. I just hollowed out a styrofoam ball with a 6mm drill bit. After that, ya bilge rat, I cut t' cotton off each end o' a plastic handled Q-tip, matey, me bucko, then pushed them about 3mm into t' styrofoam, me hearties, evenly spaced around t' hole. Next I rolled some "junk mail" around a 6mm drill bit, applyin' glue as I wound it around twice. Once t' glue dried, I cut a circle out o' a Post-it note with t' hole puncher, arrr, me bucko, shiver me timbers, and stuck this over one o' t' ends o' t' rolled junk mail (after removin' t' drill bit). I coated this whole assembly with a liberal dose o' CA, and once it dried thoroughly, inserted it into t' styrofoam ball. Ahoy! A short snippet o' Q-tip tube also serves as t' launch lug, and be unceremoniously shoved through t' styrofoam, me hearties, parallel t' t' motor tube and be trimmed flush. Ya scallywag! Simple, arrr, but effective. But here's t' gotcha- as an oversight, I didn't think about t' legs extendin' too far t' allow t' ignitor t' reach anywhere NEAR t' motor on t' Quest launcher. Ahoy! Time for Plan B. Aye aye! Build a new launcher. Begad! This be accomplished by takin' one o' me patio lights (that t' kid next door had destroyed), me hearties, me hearties, removin' t' light bulb, trimmin' some plastic, me bucko, ya bilge rat, and meltin' a hole in t' top for a launch rod. T' Quest ignitor fits into t' socket designed for t' light bulb like it was originally designed for this purpose! This makes it a true "back yard rocket" in every sense o' t' word! And since t' light be 12 volts, arrr, shiver me timbers, thar's plenty o' power. Blimey! Just turn on t' light switch inside t' doorway, and away she goes! T' other patio lights make a nice runway effect. Aye aye! Just can't forget t' replace t' light bulb afterward!

Flight:
There is only one motor for this rocket, matey, arrr, t' Quest Micromax. Prep couldn't be easier- just install t' motor, matey, like its big brother t' Spudnik. Flight characteristics are almost t' same as for t' Spudnik on an A10-3T: Slow ascent, decent altitude but nay really high, shiver me timbers, and a total cessation o' movement when t' thrust stops. Begad! It sort o' "wobbles" t' t' ground, unharmed. Begad! Ejection shoves t' motor out t' back. Well, blow me down! But, ya bilge rat, shiver me timbers, it seems t' me that proportionally, shiver me timbers, a Micromax motor has a better thrust-to-size factor than a 13mm motor. Begad! Seems these little motors pack a good wallop for their minuscule size.

Summary:
Pros: ease o' construction, cheap flights, ya bilge rat, shiver me timbers, matey, great conversation starter at barbecues, and you won't lose it in t' clouds. Begad! Cons: overall lack o' a plan from t' start led t' a design challenge in buildin' t' launcher, and t' styrofoam can't take too much abuse.

Other:
When buildin' a Micromax rocket, arrr, shiver me timbers, usin' a hollow Q-tip for a launch lug works great. Aye aye! Just cut off t' cotton.