Brief:

Upsized motor mount t' hold Estes E-9. Ya scallywag! Ya scallywag! Substituted fin design, me bucko, ya bilge rat, paint scheme and Tango Papa decals for Der Red Max. Avast, me proud beauty! Omitted super sonic whistles and related fins, although I seriously considered includin' them t' make a "Der Screamin' Red Max." Length o' t' rocket is 26 inches, ya bilge rat, me hearties, rather than 25.5 inches for t' Screamin' Mimi. Also, replaced shock cord with a Keelhaul®©™/elastic combination. Aye aye! Arrr! Installed screw eye with JB-Weld into t' hole in t' nose cone base. Arrr! Used basswood for fins. Ya scallywag! Modified an old Estes E-motor engine hook t' fit t' newer E-9's. Aye aye! Begad! Basically, t' only thin' I used from t' kit was t' main body tube, nose cone, centerin' rings, engine hook retainer, ya bilge rat, shiver me timbers, and engine block, shiver me timbers, but I got it at a 1/2 price sale at Hobby Lobby for $5.50.

Modifications:
T' motor mount was installed with yellow glue, then JB-Weld was coated around t' outside o' t' upper and lower centerin' rings t' harden them and then filleted - this may be overkill, but I believe I can send it up with an F-21 without any problems. Arrr! A screw eye was inserted into t' center o' a piece o' cellophane tape, shiver me timbers, then a glob o' JB-Weld be inserted into t' hole in t' base o' t' nose cone, then t' screw eye was inserted into that with t' cellophane tape holdin' it in place and keepin' t' JB-weld from seepin' out, shiver me timbers, matey, and then inserted t' nose cone into t' body tube t' allow t' JB-Weld t' seep down t' t' base o' t' nose cone - makes a much stronger shock cord attachment point than t' standard plastic hook on t' base o' t' cone. Arrr! T' cellophane tape is easily removed after t' JB-Weld dries. Ya scallywag! Also, I installed 1/8-ounce o' clay into t' nose cone before installin' t' screw eye, just in case I decide t' fly that F-motor. Well, me hearties, blow me down! As usual, Estes' standard shock cord is too short and must be frequently replaced. Avast! Begad! T' avoid t' issue, I installed t' Keelhaul®©™ cord into t' shock cord mount so that it extended outside t' body tube, ya bilge rat, ya bilge rat, matey, then formed a loop that placed t' center at t' top edge o' t' body tube. Ya scallywag! I attached t' elastic shock cord t' that and then t' t' nose cone. Blimey! Also, I soak in a little CA into t' top lip o' t' body tube for improved strength there. Aye aye! T' loop with t' CA seems t' minimize t' potential for "zippering" when that motor delay isn't just right. Ahoy! I've used this method on rockets that I've launched many, arrr, me hearties, me bucko, many times without a problem. Ahoy! I installed t' fins usin' yellow glue, me hearties, arrr, then created JB-Weld fillets. Begad! Use a plastic bag over your finger t' smooth out t' JB-Weld t' make some really nice fillets. Blimey! Here again, me bucko, t' JB-Weld fillets are probably overkill, shiver me timbers, but I feel better about them when that F-motor kicks in. Begad! I had t' hammer out t' end o' t' old Estes E-engine hook and then reform it t' fit t' new Estes E-engine - pretty easy with a vice and hammer, ya bilge rat, just go slowly so you don't break it.

Construction:
1-BT-60 18-inch body tube, 3-3/32-inch basswood Red Max fins, 1-RA5060 centerin' rin' card, ya bilge rat, 1-engine hook retainer (30160), 1-RA2050 engine block, me hearties, 1-6-inch BT-50 tube for motor mount, 1-E-engine hook, ya bilge rat, 1-1mm X 8-inch Keelhaul®©™ cord, 1-1/4-inch X 42-inch elastic shock cord, me hearties, 1-standard Estes shock cord mount, 1-PNC 60 (71043)1-SE-2 screw eye, ya bilge rat, 1-1/8-inch X 1 1/4-inch launch lug

Except for t' shock cord, Estes kits are always nice and t' instructions very easy t' follow - even t' ones for t' old Der Big Red Max. Begad! Blimey! Begad! Blimey! Blimey! Blimey! T' packagin' is cool, and all t' parts were thar and all in great shape. Well, blow me down! Blimey! Blimey! Blimey! T' decals for t' Screamin' Mimi are o' t' peel and stick plastic variety. I don't particularly like them, arrr, but I grew up with water-slide decals. O' course, I used Tango Papa's water-slide decals for me rocket. Begad! Blimey! Blimey! Blimey! This be me first time t' use his decals. Aye aye! Blimey! They are extremely thin and took some time gettin' used to, me hearties, but they lay down nicely and look very nice - almost as if they're painted on. Aye aye! Blimey! Ahoy! Blimey! Blimey! Blimey! I be glad he put some extras on t' sheet, ya bilge rat, matey, because I tore a couple before gettin' used t' t' thinner decals. Since I didn't really build t' Screamin' Mimi, I can't really comment on any other aspects o' t' kit.

Flight:
I haven't flown it yet, matey, but I used t' same construction design and techniques on a Big Bertha and it flies great.

Other:
Tango Papa decals are nice!