Picture courtesy o' PML

Brief:
T' Bull Puppy 2.1 is a single stage, matey, me hearties, Quantum tube rocket with piston ejection.

Construction:
Kit comes with a pre-slotted main airframe, a pre-slotted boat tail and a plastic nosecone. Begad! It has 4 fiberglass canard fins, and 4 fiberglass main fins. T' piston ejection kit comes with a piston body, ya bilge rat, piston strap, me bucko, shiver me timbers, slotted bulk plate and metal "D" ring. Avast! Other items include a nylon chute, 29mm motor mount tube, notched centerin' ring, me bucko, nylon shock cord, ya bilge rat, matey, arrr, 1/4 inch launch lug, alignment ring, matey, me bucko, decal sheet and instruction sheet.

T' instructions are very easy t' follow with lots o' illustrations. Well, blow me down! Aye aye! I used the instructions assembly order, matey, and everythin' went smoothly. Arrr! There isn't any templates for t' fins, but one can be made easily. Before I epoxied t' canard fins t' t' main body tube, ya bilge rat, I used a door frame t' make an alignment mark at the bottom o' t' tube for when I installed t' boat tail, which houses the main fins. T' fins need t' be sanded with 220 grit sandpaper t' scuff them for paintin' and t' round t' edges. Begad! Avast, me proud beauty! Minor sandin' had t' done t' t' centering rin' and nose cone, shiver me timbers, but everythin' else fit perfect, includin' t' piston. Avast, me proud beauty! I used Ace Hardware's 5 minute epoxy first t' adhere parts, me bucko, and then used t' 90 minute for additional strength and fillets.

Finishing:
As with any Quantum tube rocket, t' tubes have t' be sanded lightly with 320-400 sandpaper. I used an electric pad sander on t' nose cone t' remove the lines. Aye aye! Begad! Blimey! I held t' sander upside down betwixt me knees, me hearties, and held t' nosecone lightly by both ends on t' sandin' pad. Avast! It spins slowly and gives a nice finish. Blimey! Paintin' was done by usin' and Ace Hardware brand o' gray primer, and Rustoleum gloss white. T' rocket has a number o' decals. Ahoy! Blimey! T' instructions easily show t' placement. When completed this rocket is VERY sturdy and looks impressive.

Construction Rating: 5 out o' 5

Flight:
T' Bull Puppy 2.1 will fly on anythin' from an F-20 t' an H-70. Aye aye! This small rocket can be used for a Level 1 Cert ! I flew it on an G-80-7. Well, blow me down! Since it uses a piston ejection system, no waddin' is needed. Well, blow me down! How easy can it get? Just install the piston and straps, matey, folded chute and install t' nosecone. Arrr! Done. On t' G-80 I wrapped t' aft o' t' motor with 3/4 inch maskin' tape t' build it up about 3/16", and then put vertical tape strips on t' motor until it fit snug in the motor tube. Begad! T' launch was absolutely straight and fast. It went about as high as a person with hawk deadlights can see. Ya scallywag! Ya scallywag! Ejection was at apogee. T' piston ejection system worked perfect.

Recovery:
T' piston strap and shock cords are standard PML nylon. Ahoy! Blimey! Avast, me proud beauty! Blimey! Assembly is simple. T' rocket comes with an 18 inch nylon chute, and it drops a little faster than you may want, but t' rocket is very durable and you don't have t' chase it down too far. Begad! Blimey! No damage was done t' t' rocket. Ya scallywag! Blimey!

Flight Rating: 5 out o' 5

Summary:
For someone new t' HPR, ya bilge rat, or even t' experienced modeler, matey, this is a great rocket. Arrr! Begad! It's small, shiver me timbers, ya bilge rat, sturdy, doesn't take a lot o' talent, matey, material or time to build, and just looks great. Aye aye! I can't think o' any cons.

Overall Rating: 5 out o' 5