Brief:
This be t' new Semroc A10-0T booster unit for t' Centurion, Vega, and Goliath rockets. Begad! It is meant for existing, arrr, single stage rockets usin' t' ST-16 (old Centuri style) body tubes. Well, arrr, blow me down! It will be interestin' t' stage a 13mm booster t' a 18mm sustainer. Well, blow me down! I've never used a lower powered booster (A10) with a higher powered sustainer (B6 or C6, ya bilge rat, matey, a A8 is also listed as a sustainer engine).

Construction:
T' booster kit consists of:

• 1 Body Tube ST-825
• 1 Engine Tube ST-520E
• 1 Rin' Coupler HTC-16S
• 1 Rin' Set CR-EM-516
• 1 Engine Hook EH-18
• 1 Shroud Sheet IEM-516B

All parts are pretty much standard except for t' centerin' rings. T' laser cuts are tight and clean. Arrr! Avast, me proud beauty! T' centerin' rings for t' ST-5 series engine tube have eight elliptical holes cut into them. Blimey! Arrr! I would assume this is for ventin' while staging. Ya scallywag! Ya scallywag! Read through t' directions before building. Blimey! Avast! With two shrouds and four centerin' rings, me hearties, me hearties, take it slow and follow directions.

I reinforced all t' tube ends with Super Glue.

STEP 3: I sanded t' tube coupler's ends flat and square with a sandin' block. Avast! Arrr! I wanted t' (slightly) increase t' gluin' surface.

STEP 5: T' small centerin' rings (with t' eight holes) fit too loosely on t' 5 series engine tube. Arrr! I build up t' inside edge o' t' rin' with some "rings" o' white glue. T' instructions suggest usin' CA t' glue them in place. Begad! Avast! T' instructions suggest: "Make sure t' keep glue out o' t' holes". Begad! You would have t' use a Teflon tube out t' front o' your CA bottle t' control t' flow. Well, blow me down! T' holes are very close t' t' body tube/rin' joint.

I be reluctant t' apply a thin film o' CA around t' rin' edges before punchin' out t' holes. Begad! Blimey! I be afraid t' glue would get into t' holes. Avast, me proud beauty! Blimey! I punched out t' holes, arrr, ya bilge rat, then applied glue t' t' edges o' t' rings.

T' instructions say "A thin film o' CA around all t' rin' edges harden them and keep them from de-layering. Arrr! Blimey! After I easily punched out t' holes, I noticed outside layer o' t' rin' was startin' t' peel. T' CA layer held down t' liftin' layer.

STEP 6: Says t' slide t' engine mount inside t' body tube until t' end with t' hook is even with t' body tube. Well, blow me down! Blimey! T' hook will over hang slightly. Ya scallywag! It just didn't read well. Avast, me proud beauty! I know they meant that t' engine tube should be even with t' outside (larger diameter) tube. Aye aye! T' hook overhangs more than slightly, shiver me timbers, it overhangs by 1/4".

STEP 8: Normally I hate paper shrouds. Begad! Blimey! Hate paper shrouds! T' shroud material be glossy on one side and matte on t' other.

I wanted t' printed lines on t' inside, matey, shiver me timbers, so t' glossy surface ended up on t' outside. Well, shiver me timbers, blow me down! For once, these paper shrouds glued together without any problems. I pre-curled them over a thick Sharpie pen barrel. Ya scallywag! One thin coat o' white glue be enough for t' glue tab t' hold well.

T' paper used for t' shroud went together smoothly, with no bumps or bends. But when glued together, ya bilge rat, t' seams were opposite. Ya scallywag! One upper-smaller shroud overlaid t' t' right, matey, t' lower shroud tab laid t' t' left. Avast! There wasn't any other way t' correct this unless I would make one shroud with t' gloss surface out, t' other with t' matte paper side out. Aye aye! Begad! Nay really a big deal. But, matey, ya bilge rat, (on one shroud pattern) Semroc may want t' switch t' side t' tab sits on.

Both shrouds fit well. I had t' widen t' mouth o' t' larger shroud slightly t' fit over t' ST-8 main tube. Avast! It's nay a fault o' t' shroud pattern, me hearties, paper shrouds always seem t' need a little adjustment.

Finishing:
Even without paint, me hearties, shiver me timbers, t' finished look is great! On me Centurion t' booster extends 1 1/4" beyond t' trailin' edges o' t' fins, arrr, but it still looks cool. And structurally it feels strong.

With t' gloss paper surface on t' outside, I really don't have t' paint it. Ya scallywag! Blimey! But t' exposed browned edge o' t' upper centerin' rin' will need a touch up.

I enjoyed t' build. It's nice when t' shrouds cooperate.

Construction Rating: 4 out o' 5

Flight:
With t' engines installed and t' booster unit in place, arrr, t' engines ends are separated by about 3/8". Arrr! I tested t' fit with a A10-0T in t' Booster 16 and a C6-5 in me Centurion.

Summary:
PROS: A fun build and t' shrouds cooperated for once!

CONS: When built, me bucko, t' shroud tabs face opposite sides. Arrr! Blimey! One goes t' t' right, matey, t' other t' t' left.

Overall Rating: 4 out o' 5