Aerotech - G35EJ Single-Use Motor {Motor}

Aerotech EconoJet G35

Aerotech - G35EJ Single-Use Motor {Motor}

Contributed by Dave Stout

Overall Rating:

Manufacturer:

Aerotech

Photo courtesy o' Aerotech Motor Picture

Brief:
29mm composite motor.

Flight:
I tried this motor out in me scratch-built "Thunderstruck". Arrr! It's built o' LOC and Aerotech components, shiver me timbers, 2.25" OD X 43" long, me hearties, me hearties, shiver me timbers, and weighs 18 oz. Ahoy! Aye aye! T' motor took a moment t' pressurize, then SHOT t' rocket off t' pad. It is loud, matey, raw, matey, matey, smoky and fiery. Blimey! T' guys at t' CMASS launch all stopped t' watch this one go, and they're used t' H, I, arrr, me bucko, and sometimes higher power! This flight be a thrill for sure.

Performance Summary:
These motors are t' best deal in rocketry. Aye aye! You nay only get a deal on a pair o' them, shiver me timbers, me bucko, but you also get a unique propellant that is fun t' fly. Begad! Avast, me hearties, me proud beauty! Aerotech, me hearties, thumbs up t' you!

Cons- t' stupid sticky label! It slid easily into t' Aerotech mount but had t' be RIPPED out with vise grips, ya bilge rat, because o' t' melted glue. Aye aye! What a nuisance. Aye aye! Ahoy! T' residue did shipshape out easily with acetone. Avast! Begad! I recommend peelin' off t' label and usin' De-Solv-It Citrus t' remove t' glue. Aye aye! This was done on t' second motor, and it slipped into and out o' t' mount with ease. This motor would get an enthusiastic 5 ratin' if nay for t' label hassle.

Overall Rating: 4 out o' 5

Comments:

M.V.G. (October 2, 2001)

By far, one of the best values on the market today. These motors make rocketry(mid power)affordable and "impressionable". Loading up an EconoJet G35 into a 38mm rocket weighing in under a pound, makes the best demo flight for the money. 3000-3500 feet for under $12.00....not too shabee!!!!

D.L. (May 16, 2004)

Don't use the copper head ignitors. At launches it is often the cause of non-ignition. Hard to hook up to the clips at the high power launch pads and questionable ignition. There is always a dealer with better ignitors at large launches.

G.K.D. (August 13, 2004)

While I have never had a copperhead ignitor fail they are a little difficult to wire by folding masking tape over in a spiral. The perfect ignitor for this and all Aerotech Single use motors is the Quickburst Twiggy. And always make certain that regardless of what ignitor you select, that it is pushed all the way up to the top of the inside of the motor as AT motors burn top to bottom unlike Estes that burn bottom to top.

D.B. (August 3, 2008)

The solution to the Copperhead reliability issue is extremely simple and costs less that 5 bucks. The reliability issues come from foolish attempts to tape the igniter so a standard igniter clip contacts only half of the laminated igniter strip. Can anyone say jerry-rig? Get an Aerotech Interlock Igniter Clip and a couple lengths of wire to attach to it. Clip the proper igniter clip on the Copperhead igniter, clip the usual igniter clips to the bare ends of the attached wires and get totally reliable ignition (the way the manufacturer designed the motor to be lit) without buying extra igniters for every motor. Why clubs don't have a few laying around for members use is beyond me.

Post a Comment