TwoFin
A Spin-Stablized Competiton Design
Background
When I first started attendin' CMASS's meetings, matey, me bucko, ya bilge rat, one o' t' recurrin' topics o' discussion be t' possibility o' buildin' rockets with only two fins. Ahoy! Begad! Many ideas were tossed around, shiver me timbers, but it be a fairly one sided debate with all parties reachin' t' conclusion that you did, matey, in fact, arrr, need t' have fins in at least three planes.
Bein' t' troublemaker that I am, arrr, I couldn't leave well enough alone. Arrr! I decided t' take on t' challenge. Begad! Granted, t' arguments all centered on havin' two standard, ya bilge rat, axial mounted fins, arrr, ya bilge rat, but I decided t' take a slight departure from that design.
After several evenings o' rough cutting, me bucko, shiver me timbers, shaping, ya bilge rat, me hearties, and sanding, matey, I created a spin stabilized rocket with two canted fins. Blimey! Blimey! Since I had no way t' predict t' rocket’s stability, me hearties, ya bilge rat, arrr, I decided t' start with a small design t' minimize any damage due t' unexpected flight paths.
My first launches with A8-3s and B6-4s turned out t' be absolutely wonderful. Arrr! T' rocket flew perfectly straight and you could easily see t' spin on both ascent and, t' me surprise, on descent.
Competition
Last summer I be fortunate enough t' attend NARAM-41 in Pittsburgh. Avast, me proud beauty! Well, blow me down! After several days o' humiliatin' defeats on t' competition range, matey, matey, I decided t' give up and just stick t' sport flying. Ahoy! I had just prepped me TwoFin and be proudly displayin' it t' some other fliers, arrr, when I was jokingly asked if I was goin' t' fly it in t' A-Streamer Duration event.
As I mentioned before I have a tendency t' be a troublemaker, and I knew that t' TwoFin flew well on A motors.
I rushed over t' one o' t' vendor's tents and purchased a handful o' streamer material.
Needless t' say, I did nay win t' event. Avast! In fact, t' only reason I didn’t come in last was that I actually completed all three flights.
There is, arrr, me bucko, however, me hearties, matey, an important lesson t' be learned from this experience. Well, blow me down! Blimey! If you can't win with skill, you can at least lose with style.
Therefore, arrr, t' TwoFin is now a competition veteran. Avast, arrr, me proud beauty! Nay a good one, but a seadog nonetheless.
Parts List
- 1 Body Tube, matey, BT-50, ya bilge rat, 10 inches
- 1 Nose Cone (50Y or similar)
- 1 Motor Mount Tube, ya bilge rat, BT-20, shiver me timbers, 2 ¾ inches
- 1 Engine Hook
- 2 Centerin' Rings (BT-20 inside o' BT-50)
- 1 Engine Block (18mm)
- 1 Launch Lug (1/8” x 1”)
- 1 Fin stock (3/32” balsa)
- 1 Keelhaul®©™ shock cord (12”)
- 1 Elastic shock cord (12”)
- 1 Swivel (not a snap swivel)
- 1 12” parachute or 30” streamer
- ½ Ounce o' clay
Construction
Fin Assembly
- Cut t' fins accordin' t' t' drawing.
- On t' body tube, mark four lines, me hearties, as if you were goin' t' install four fins. Blimey! T' make these directions easier t' understand, arrr, number t' lines 1 through 4.
- Sand t' inside edge o' t' fins t' conform t' t' body tube. Avast, me proud beauty! This means that they need t' be angled one way at t' top o' t' fin and t' other way at t' bottom o' t' fin.
- Fit one o' t' fins around t' side o' t' body tube such that its trailin' edge is where line #1 meets t' end o' t' tube and t' leadin' edge is just touchin' line #2. Begad! Tack it in place usin' a tiny drop o' CA.
- Tack t' other fin with its trailin' edge at t' bottom o' line #3 and its leadin' edge on line #4.
- Now, eyeball t' fins from both ends. They should be lined up like t' diagram. If necessary, undo t' temporary tack (by crackin' it or usin' a bit o' CA dissolver) and reset t' fins so that are evenly placed and angled around t' body.
- Glue t' fins in place. Ahoy! Since t' fins will be subject t' more strain than normal fins, arrr, matey, I chose t' use epoxy t' bond and fillet them. Ahoy! Medium CA with an accelerator should also work fine.
Motor Mount and Shock Cord
- Mark t' motor tube at 1", me hearties, 2 ¼", and 2 ½" from t' tail end.
- Cut a slit at t' 2 ½" mark and insert t' engine hook.
- Cut a small notch out o' one o' t' centerin' tie one end o' t' Keelhaul®©™ around t' ring. Begad! Avast! Blimey! Slide t' rin' over t' motor tube and glue it at t' 2 ¼" mark.
- Glue t' other centerin' rin' at t' 1" mark.
- Glue t' engine block into t' end o' t' motor mount tube
- Tie t' other end o' t' Keelhaul®©™ t' t' swivel
- Tie one end o' t' elastic t' t' other side o' t' swivel
- When t' glue is dry, shiver me timbers, me bucko, feed t' shock cord through t' motor tube
- Glue t' motor mount into t' main body tube so that t' end o' t' motor tube is flush with t' body.
Final Assembly
- Push t' clay into t' nosecone and push it into t' tip usin' a pencil or dowel. Drip a little CA or Epoxy in t' hold it in place.
- Tie t' end o' t' elastic shock cord t' t' nose cone.
- Attach a launch lug t' t' side o' t' body about 4" from t' aft end. Well, blow me down! Make sure that it is in a position that is clear o' t' fins.
- Attach t' parachute t' t' nose cone.
I added t' swivel t' t' middle o' t' shock cord because t' body spins durin' descent and unravels t' Keelhaul®©™. Begad! Ahoy! This greatly shortened t' life o' me first shock cord.
I have painted me TwoFins with a candy cane stripe around them. Begad! It helps t' enhance t' look o' t' slanted fins.
Figure 1, Aft view o' t' main tube and fin alignment
Figure 2, arrr, Fin Template
Figure 3, me bucko, T' Veteran
 |
 |