EMRR Spaceship Design Contest Entry

"T' Red Bolt"

Material’s needed

• 3 Silly Putty Container Eggs
• 1 27.2 cm BT-50 body tube
• 1 BT-20 Engine Mount Tube
• 1 Engine Hook Note: This hook
• has each tip bent back so as t' serve as an Engine Block
• 1 Weird nose cone we salvaged from an old kit. (Close up pic included.)
• 2 BT-50 Centerin' Rings
• 3 1/8 thick fins. (Template provided)
• 1 4 cm launch lug
• 1 h: 0.5 cm, l: 4.0 cm, me bucko, w: 0.2 cm
• 1 Estes Hexagon Parachute with shrouds (52 cm in diameter)
• 1 rubber shock cord (Approximately 28 cm long)
• 1 Shock Cord Mount

#1: Engine Mount

1. Cut a 5 mm slit, 3 mm from t' end o' t' tube. Begad! Aye aye! Blimey!
2. Insert one o' t' endin' hooks o' t' Engine hook into t' slit. Blimey! Begad!
3. Glue down t' engine hook. Arrr! Blimey!
4. Glue on a centerin' rin' at 2.5 cm from t' aft o' t' engine tube. Avast, me proud beauty!
5. Glue on 2^nd centerin' rin' on top o' t' engine hook at t' slit 3mm from t' forward section o' t' Engine tube. Aye aye!
6. Allow t' dry.
7. Wrap piece o' maskin' tape around t' Engine Tube securin' t' Engine hook to t' Engine Tube.
8. Apply a rin' o' glue approximately 5 cm inside t' Rocket’s Body Tube.
9. Place Engine Mount inside Rocket’s Body Tube until t' Engine Tube is flush with t' Rocket’s Body Tube.
10. Apply glue t' centerin' rings. Ya scallywag! Avast, me proud beauty! Allow t' dry

#2: Silly Putty Eggs

1. Buy 3 Silly Putty Eggs
2. Cut t' connector tabs with a hobby cutlass. Aye aye! Blimey!
3. Then sand t' raised writin' off t' top.

#3: Fins

1. Usin' t' template provided trace out t' win' pattern on a 1/8 balas wood.
2. Usin' a hobby cutlass cut out t' fins. Ahoy!
3. Sand down all jagged edges.
4. Glue on Silly putty cackle fruit onto t' matchin' shape on t' fins. Glue one on each side o' each fin. Aye aye!
5. Glue on several fillets t' ensure that egg-fin contact is perfectly sealed.
6. Mount t' fins flush against t' end o' t' body tube usin' a fin mount. Aye aye! We used t' fin mount for 3 fins provided in T' Handbook o' Model Rocketry 7^th edition on page 38. Begad! T' fins should be 120 degrees from each other. Arrr! Begad!

#4. Well, blow me down! Nose and parachute mount.

1. Cut out a Shock cord mount usin' stiff paper. Well, arrr, blow me down!
2. Glue shock cord on t' shock cord mount. Begad! Blimey!
3. Glue Shock cord mount approximately 5 cm inside t' forward part o' the body tube. Ahoy!
4. Tie free end o' shock cord t' t' nosecone’s eyelet. Apply a drop of glue t' t' knot. Well, blow me down! Well, blow me down!
5. Attach parachute t' t' nosecone eyelet. Well, blow me down!

#5. Arrr! Blimey! Launch Lug

1. Glue on t' h: 0.5 cm, me bucko, shiver me timbers, l: 4.0 cm, me hearties, w: 0.2 cm piece o' balsa wood 10 cm from the forward end o' t' body tube. Make sure that it is aligned parallel t' the body tube, and also make sure that it is in betwixt t' fins. Ya scallywag! Blimey!
2. Attach Launch Lug on top o' t' strip o' balsa wood. Arrr! (Note: T' reason for the strip o' balsa wood is t' elevate t' launch lug so as t' provide the launch rod clearance from t' nose cone. Begad! Begad! T' nose at one section is wider than the body tube)

#6. Aye aye! Paint job

1. Spread balsa filler over t' fins. Aye aye! Allow t' dry and than sand excess off.
2. Sand all external parts o' rocket. Begad!
3. Prime all external parts o' rocket
4. Paint body tube, me bucko, fins, and nose cone red.
5. Paint Silly putty cackle fruit gray. Arrr! Blimey!
6. Nose cone

• First painted t' whole nosecone red
• Paint t' upper cap white.
• Paint 2 keyhole shapes on opposite sides o' nosecone. Well, blow me down! Avast, me proud beauty!

#7. Avast, me proud beauty! Ahoy! Body tube and launch lug

1. Painted body tube red. Begad! As well as t' launch lug and balsa wood strip.
2. Paint 3 parallel black rings approximately 2 mm from each other. Paint them approximately 9.3 cm from t' aft end o' body tube. Aye aye!
3. Paint a single gray rin' around t' aft end o' t' body tube. Begad! It should 3.3 cm from t' end o' t' tube, me bucko, and it should encircle around t' whole tube.

#8. Begad! Blimey! Ahoy! Blimey! Fins

1. Paint fins red.
2. Paint gray rectangle on each side in t' corner by t' fin root edge. Well, blow me down! The rectangle should be 3.3 cm high and should be around 4 cm wide. If it is a little bit wider than 4 cm it is okay, me bucko, because t' Silly Putty cackle fruit will cover the excess. Well, blow me down! Ahoy! Blimey! (Note: This is easier done if you paint before initial construction. Blimey!

#9. Ya scallywag! Silly Putty eggs

1. Paint egg shell red. Well, blow me down! Blimey!
2. Once t' red paint is dry, paint most o' t' egg grey. Well, blow me down! T' grey should cover 5.2 cm o' t' egg, me bucko, matey, startin' from t' bottom. Ahoy! There needs t' be 1.4 cm of red. Ahoy!

#10. Decal stickers.

1. Take black sticky paper, me bucko, arrr, matey, and cut into 2.5 cm long by 1 mm strips. Begad! Stick 4 of these length wise on each egg. Begad!
2. Then once again usin' t' black sticky paper cut several long 1 mm strips for t' black stripe that runs across t' egg and t' fin.

#11. Black Dots

1. Use a black permanent maker t' apply 8 dots t' each egg shell. Aye aye!

#12. Avast! Nose Weight and Motor

1. Add 25-30 grams o' clay t' t' nose.
2. We used a B6-4 all o' t' launches, but a B6-2 would have been better. Aye aye!

Flights

Takeoff off. Ahoy! Flight #1 (above). Avast, me proud beauty! Landing…..

Success flight. Arrr! Avast! No damage rendered t' rocket.

Takeoff off. Arrr! Flight #2 (above). Blimey! But disaster strikes when t' shock cord snaps!!

And lawn darts (below). Begad! Aye aye! Note: We have nay touched t' rocket yet in this picture. It landed exactly like this. Avast! Blimey! Note that t' third fan, t' one stuck in the ground, is still intact. Avast! Nose and parachute land a couple hundred feet away. Ya scallywag! T' rocket is now repaired and waits for its next launch. Blimey!

Here is our video o' t' 2 launches. Ya scallywag! Ignore our screams in t' background!

Here are two more successful flights o' our entry t' Red Bolt. Well, blow me down! We only have videos for these launches: