ICRS Ghost Rider

by Mike Crewe

Construction.

Parts.

For t' parts, I used t' parts list, arrr, me bucko, rather than t' actual kit.

In t' parts list, it has "launch lugs and recovery system as necessary for safe operation ".
I expanded this to:

• Two 1" launch lugs
• Approx 18" o' Keelhaul®©™® cord. Avast, me proud beauty!
• 24" o' 1/8" elastic. Begad! Arrr!
• 1/4" section cut from used 18mm motor case. Ahoy! Well, me hearties, blow me down!

T' motor clip from t' parts list was nay used.

T' card stock layout, fin templates, shiver me timbers, arrr, ya bilge rat, and tube markin' wraps, were all created at 150 dpi.

Upper Section.

(Note. All construction images here are linked t' a higher resolution picture)

Two 5" lengths, me hearties, and a 3 1/2" length were cut from t' BT20. Usin' t' "BT20 Main Wrap", all three tubes were marked and lined. Begad! Usin' t' "BT20 Top Tube Wrap" (and aligned on t' 'B' line) a diagonal was drawn around one end o' t' 3 1/2"  tube.  Each tube be marked at 7/8" along t' 'C' lines (at t' opposite end from the diagonal on t' short tube), shiver me timbers, and this rectangular section was cut out, and the bits saved for later. T' diagonal was cut off t' end o' t' short tube.
T' three tubes were then glued together, along t' 'S' lines, with t' cut out bits formin' a BT20 size 'hole' in t' middle. Ya scallywag!
1 3/4" was cut from t' rest o' t' BT20 for t' front coupler. One o' t' centerin' was rings glued t' t' top o' it. T' two extra rings were then cut from t' card stock, and glued together, halfway down t' coupler. This be then glued into t' gaps betwixt t' three tubes, ensurin' it was straight and in line
A 5 1/2" section was cut from t' BT50, matey, and be marked usin' the "BT-50 Top Wrap". T' tube was slit along these lines for 1 1/2 " T' smaller sections were then trimmed into a taperin' triangle shape.
T' BT50 section was then glued onto t' front coupler, shiver me timbers, ya bilge rat, with t' large sections slidin' inside t' BT-20 tubes, arrr, and t' triangular sections on the outside. T' triangular sections were then glued down into t' gaps betwixt t' BT-20 tubes, formin' a sort o' transition.
T' three top transitions and t' couplin' collars were then cut from the card sheet, and rolled around one o' t' BT-20 nose cones t' get t' basic shape. Usin' a collar, each one was joined t' t' end o' one o' t' BT20 tubes, ya bilge rat, and the edges stuck onto t' BT50. After this was all dried, shiver me timbers, I applied a thin coat o' CA over t' whole area for strength, and then sanded it smooth.
T' oval end cap and cabin housin' were cut from cardstock. Avast! Blimey! T' cap was stuck onto t' angled end o' t' shorter BT20, ya bilge rat, matey, and t' cabin formed and glued on in front o' it. T' two nose cones were then attached t' t' longer tubes.
A 2 1/2" length was cut from t' BT50. Avast! A section was then cut out of the side, ya bilge rat, shiver me timbers, t' make it t' same size as BT50 coupler. Avast! T' rectangular sections cut from t' BT20 front tubes (well, me hearties, me bucko, two and a bit o' them actually) were stuck on t' inside t' keep it together. T' detached shoulder from t' BT50 nose cone (called t' BT50 bulk head in the parts list) was cut in half, arrr, and a loop o' Keelhaul®©™® tied through t' bottom bit. This was then glued into t' forward end o' t' coupler. Begad! T' whole coupler was then glued halfway into t' top BT50 tube. Begad!

Lower Section.

T' end was then cut off t' BT50 nose cone, leavin' it about 2 1/4" long. Arrr! With a bit o' sandpaper wrapped around a spent 18mm motor, t' inside was sanded out until t' remainin' length o' BT20 (the motor mount) could pass through. Well, blow me down! Avast, me proud beauty! This left t' tail cone 2 1/10 " long. T' other part o' t' nose shoulder was glued into place on t' wider end. T' other centerin' rin' was stuck on t' end o' t' motor mount,  then this unit be glued inside t' tail cone. About 1/8" o' motor mount stuck out o' t' bottom o' t' cone. A 12" length o' Keelhaul®©™® was then tied t' a 1/4" section cut from a used motor case and this was glued inside t' top o' t' motor mount. Avast, me proud beauty! Blimey! A loop be tied in t' other end of the Keelhaul®©™®.
T' remainin' 10" o' BT50, was then marked up usin' t' 'BT50 Base Wrap', shiver me timbers, before t' tail cone be glued t' it. T' 'F' lines were extended down the tail cone. From t' card stock, me hearties, t' six aft pods were cut out and glued together.  These were then glued onto t' BT50, along t' 'P' lines, with t' end o' the straight section o' t' pods in line with t' end o' t' tube.
Usin' t' fin templates, arrr, t' fins were marked out (the layout can be found here) on t' balsa sheet, then cut out. Aye aye! They then had a couple o' passes through t' 'sand - sandin' sealer - sand' process. T' main fins were than attached t' t' tail cone along t' 'F' lines. T' dowel be cut into three equal pieces, and glued onto t' small forward fins.
T' forward fins were glued onto t' body, shiver me timbers, in line with t' main fins, with the leadin' edge 3.9" from t' top o' t' air frame. Arrr! Blimey! T' top end o' the dowels be glued t' t' tip o' t' main fins, me bucko, me bucko, and after t' bond had set, were trimmed and sanded t' t' correct size and angle.
A 1" launch lugs be glued onto a forward and matchin' main fin. Begad! These were positioned t' allow t' launch rod t' pass betwixt t' main fin and the rear pod.
Finally, arrr, t' completed rocket was sprayed with a coat o' primer, two foot of 1/8" elastic was was tied betwixt t' loops in t' Keelhaul®©™®, and t' 18" parachute was attached t' t' top loop. It was now ready for flight testing.

Flight Test

Stability

Firstly, I ran a quick CP calculation, with t' top section simulated as follows:

• 4" long, me hearties, 1½" diameter parabolic nose. Aye aye!
• 4" o' airframe. Avast, me proud beauty! Arrr!
• 2" long transition t' t' BT50. Avast! Blimey!

This gave a CP o' 19.4" (from t' nose).
With t' rocket fully prepped and loaded with a C6, t' CG was found t' be just aft o' t' leadin' edge o' t' forward fins, ya bilge rat, at 15.9"
This indicated a stability margin o' 2.6 calibres, so no nose weight was added.
To confirm t' stability, me hearties, a swin' test be also performed successfully with the same motor loaded. Aye aye! Well, me bucko, blow me down!

Motor Selection

T' rocket be weighed without a motor loaded, and was found t' be 53g (1.868 oz).
Usin' this figure, shiver me timbers, and a guesstimate for t' CD o' 0.8 some runs were carried out usin' rasp, me hearties, which gave t' followin' results:

From this, matey, t' recommended motor list looks like:

• A8-3
• B4-2
• B6-4
• C5-3
• C6-3

First Flight

It be very windy at t' flyin' site, me bucko, so I swapped t' parachute for a large streamer, and loaded up a B6-4 motor, me hearties, ya bilge rat, and let her go.
T' flight was incredibly straight considerin' t' wind - I be expectin' a lot of weather-cocking.
Deployment occurred just after apogee, and t' rocket be recovered without damage. Ahoy! Ya scallywag! A success!