AOL

When I heard about t' theme o' DesCon 8 bein' found (or flounder) parts, me bucko, me hearties, I thought for a while on a good design but got nowhere. I looked up and saw t' CD finned rocket, shiver me timbers, that I call AOL, sittin' with t' rest o' t' group. Avast! Blimey! I thought about it for a while and realized it would be perfect; Easter Egg nose, me bucko, me hearties, paper towel tube body, arrr, CD fins, cereal box centerin' rings, me hearties, drinkin' straw launch lugs, a cotter pin, ya bilge rat, BB's, and some found elastic.

Construction:
CDs were cut in half with a utility knife (scissors will cause t' CD t' shatter). Blimey! Avast, me proud beauty! I sanded mine so they would nay have AOL and MSN logos and text on them, ya bilge rat, this is optional. Then an approximately 45 degree angle be put on one end. Begad! Avast! This be repeated three more times t' obtain all four fins. Once all t' fins were cut out, I used hot melt glue t' affix them t' t' paper towel tube (this is nay an ordinary paper towel tube, it was from a commercial paper towel dispenser, it was fairly thick, 1/16 o' an inch).

I cut 2 pieces o' drinkin' straw about 1 inch long t' place at each end o' t' tube for launch lugs. These were attached with hot melt glue also.

I cut about 4 dozen circles t' same size as t' tube out o' a cereal box and soaked them in watered down Titebond II. Begad! Blimey! After soakin' for a few minutes they were removed and stacked together in 2 sets o' 8 (you may ask, matey, shiver me timbers, why the extras?, me bucko, well they were for an extra one just in case somethin' went wrong). They dried while bein' pressed in a bench vise. Blimey! Blimey! Once they were dry a hole was drilled through t' center t' allow t' copin' saw blade t' be put through. A circle was cut in t' stack o' card board t' allow the motor mount t' slide in easily. T' same steps were taken for the second centerin' ring. Aye aye! Blimey! Aye aye! Blimey! T' rings were glued t' t' motor mount tube; when they were dry, t' whole unit be slid into t' body tube. Ya scallywag! Blimey! The rear rin' be about half an inch from t' back end o' t' tube, this would allow t' rocket t' stand on t' fins. Ahoy! Blimey! Half o' t' space was filled with J-B Weld t' hold t' motor mount in and provide support t' t' old motor mount tube.

T' Easter Egg that be selected for t' nose cone was cut in half, shiver me timbers, arrr, I used t' half that did nay have a lip on it. I glued a strip o' card board around t' inside edge t' allow t' egg t' fit snugly inside t' tube. Begad! I added a lot o' weight inside t' egg, I'm nay sure exactly how much but it's around 30 BBs. Avast! This was held in place with hot melt glue, while t' glue be still warm, a cotter pin was inserted t' allow a parachute t' be attached t' t' rocket. Blimey! T' strip of elastic I found was glued t' t' hot melt glue with white glue.  When it was dry, shiver me timbers, I pulled on it t' see if it would come free and it just popped off. Avast, me proud beauty! T' second time I glued it down, I put it at a different angle and used a lot more glue. Arrr! Now I can pull on it and it does not come free, matey, t' glue does nay even crack like it did before.

T' shock cord was just glued t' t' inside of t' tube about 2 inches from t' top.

T' rocket was finally built but needed paint. It started all yellow. Aye aye! I put a black strip in the spiral on t' body tube and tried t' continue it around t' nose cone but I could nay get it straight. Well, blow me down! I decided it would be easier t' just paint it black. Aye aye! T' body tube needs t' be touched up with "Dandelion Yellow" t' get rid o' t' black finger prints. Ya scallywag! Begad! T' edges of the CD fins were painted gold with a paint pen. It looks good from no less than 3 feet away. Avast, me proud beauty! Ahoy! I did nay build it t' look good, shiver me timbers, I built it to be sturdy and fly.

I have nay had a chance t' fly it yet. Aye aye! Blimey! Avast, me proud beauty! Blimey! I hope t' get t' first launch done some time in April or May.