Brief:
I have t' admit, arrr, a key motivator for me entry in t' Box O' Parts contest this year was simply an excuse t' get rid of some stray rocketry junk, ya bilge rat, some o' which be leftover from last year's contest. Well, matey, blow me down! Blimey! I gleefully tossed some interesting doodads and a fair amount o' stuff that I'd accumulated over t' years with simply no hope o' ever using, ya bilge rat, anticipating I'd come out ahead on t' swap. Well, blow me down! Blimey! O' course, I also procrastinated and didn't bother enterin' until just before the deadline, only t' learn that no swap partner was available and I'd be stuck buildin' me own stuff. Begad! Blimey! On top o' that, me bucko, matey, matey, my bonus/surprise items included a foam egg carton/cell, 10 toothpicks, ya bilge rat, me bucko, matey, dental floss, a stick pen and a pill bottle. Yikes!

Construction:
I then went into immediate and hardcore procrastination mode again, nay even thinkin' about t' model until t' week of t' revised deadline. Thank goodness me plant closed down, eliminatin' me job, matey, or else I would never have had time to put together a decent model!

As I stared at me box o' parts, shiver me timbers, t' pressure o' t' deadline be sufficient t' spark just a touch of inspiration, matey, and I decided I'd have t' involve some type o' egg-loftin' payloader. Well, blow me down! T' concept smartly emerged o' an alien "ark", whose mission would be t' colonize a distant planet by droppin' a cackle fruit with a new life forming within. These are self-reproducin' aliens o' course, so I would only need t' carry and deploy one egg, ya bilge rat, nay two. Avast! I then went about t' process o' buildin' a carrier vessel worthy o' haulin' a cackle fruit across t' galaxies. Or at least as far as I could get on an 18mm motor.

T' parts list I wound up usin' included:

• BT-20 cut t' 17" length
• 2 CR 50/20 centerin' rings
• 2 parachutes (12" plastic)
• Keelhaul®©™ and elastic shock cords
• BT-60 cut t' 6"
• 7 3/32" balsa spacers 10.5mm x 50mm (these aliens use both metric and imperial dimensions)
• BT-50 cut t' 3.5"
• 2 pin' pong balls
• 3 Styrofoam balls (1" diameter)
• 1 large plastic Easter egg
• 3/32" balsa fin set (see pattern 1)
• 3/32" balsa tube support (see pattern 2)
• 3/32" balsa harpoon support (see pattern 3)
• 4 BT-20 pods cut t' 43mm length
• BT-20 cut t' 1" length for coupler use
• 10 toothpicks
• 10" dental floss
• 1 Bic/Papermate pen
• 1 pill bottle
• 2 egg carton cell halves (enough t' hold one egg)
• 2 3/16" launch lugs 1.5" length
• 2 3/32 balsa standoffs 0.5 x 1.5"

Buildin' forward along t' airframe now, ya bilge rat, I measured off on t' BT-20 1 inch forward o' t' BT-60. I grabbed one of t' pin' pong balls and usin' t' technique from many a Shrox design (ex. Begad! Begad! Fliskits Alien 8), cored out a 19mm hole on opposin' "ends" o' t' ball. T' do this, simply press t' end o' a BT-20 against t' ball, ya bilge rat, trace around the joint with t' ball, me hearties, then usin' a sharp hobby cutlass score t' marked line several times. Eventually you'll start to cut through t' ball. Ahoy! Sand smooth so that t' tube just barely fits through, matey, then push t' tube all t' way through until it's touchin' t' opposite wall. Arrr! You might have t' hold t' ball up t' a bright light at this point t' see, but there will be a shadow against t' surface where t' BT-20 wants t' come through. Ya scallywag! Mark that circle, ya bilge rat, ya bilge rat, remove t' BT-20, and repeat t' scoring/cuttin' process. Ya scallywag! Voila! You now have a pin' pong ball that can slide down a BT-20. Begad! Apply a generous bead o' glue on t' main BT-20 at t' mark 1" forward o' t' BT-60 and slide t' pin' pong ball down until it just reaches this point. Once t' glue has set, shiver me timbers, apply a small fillet t' t' other end. Begad! Blimey! Grab another pin' pong ball and core it out for another BT-20 hole, ya bilge rat, but set it aside.

Once t' first ball's glue joints have grabbed, take t' 3.5" BT-50 and slide it down t' main BT-20. Ya scallywag! Begad! No centerin' rings will be necessary, as t' pin' pong balls will hold it in place. Blimey! Take t' other pin' pong ball, me bucko, slide it down t' BT-20 and press it against t' BT-50, ya bilge rat, wedgin' it in place against t' first ball. Avast, me proud beauty! Begad! Now apply a bead o' CA around t' forward seam o' t' second ball so that it grabs smartly and frees up your hands. Begad! Well, blow me down! Follow up with white glue fillets around t' BT-50/pin' pong ball seams.

I now grabbed t' large plastic Easter egg capsule. I wanted t' use this as t' egg carrier and nose cone, arrr, matey, but needed a piece o' coupler stock t' do this. Blimey! Blimey! Since I didn't have any, ya bilge rat, I cut a 1" length o' BT-20 t' make a coupler. This little trick comes in handy, especially doin' field rework in NARRRRR contests—I made a vertical cut along t' tube, then pinched on end under/inside t' other, and pushed this into t' end o' t' main BT-20, leaving about 1/4" exposed. Ahoy! Blimey! I took a pencil and made a mark at t' overlap point. I then pulled this back out o' t' main BT-20, matey, me bucko, extended t' mark along t' length o' t' coupler piece, ya bilge rat, and cut along that line, arrr, removin' a tiny section o' the tube. Begad! Blimey! Blimey! Blimey! This section then becomes an overlap tab. Avast! Blimey! Begad! Blimey! I tacked it t' t' inside o' t' coupler piece with half t' tab exposed beyond t' cut line. Avast! Blimey! Once that set, I tacked t' other side t' t' overlap tab formin' a butt joint (see photo). T' result is a perfect-fittin' coupler.

T' egg capsule is a bit larger than most eggs, so t' protect t' egg I used two halves o' egg cells from an egg carton, me hearties, plus a little dog barf padding. Ahoy! I used Mylar tape t' seal t' two capsule halves together, though plain old maskin' tape or electrical tape would work fine as well, matey, just nay look as nice.

I wanted t' dress up t' middle o' t' rocket as well as use up more stuff, so selected 6 toothpicks and t' 3 Styrofoam balls. Aye aye! Avast, me proud beauty! I inserted 2 toothpicks into each ball at roughly 90 degree angle, me hearties, ya bilge rat, and adjusted t' depth a bit to line up with t' joints where t' BT-50 meets t' pin' pong balls (see photo). I tacked each assembly in pace with CA, mountin' them in alignment with t' 3-fin markings from t' BT-20 (markin' t' BT-50 for 3-fin and alignin' t' marks with t' BT-20 would probably have been smart, matey, me bucko, but that would be out o' character for me).

At this point, arrr, I was ready t' mix up a small batch o' epoxy. Avast, me proud beauty! Begad! I went with 15-minute regular hobby grade (the thick stuff that sort o' oozes out). Begad! I grabbed some dental floss t' use as a shock cord for t' egg capsule, me hearties, tied a couple knots in each end, me hearties, and then taped each end t' an opposin' side o' t' coupler, me hearties, with t' resultin' loop pushed out what will be t' aft end o' t' coupler (see photo). Well, blow me down! Well, arrr, blow me down! I applied a generous bead o' epoxy along t' inside and forward edge of the coupler, then attached it t' t' bottom o' t' egg capsule, ya bilge rat, trappin' t' floss in betwixt with t' knots outside. Begad! I set that assembly aside t' cure out.

I then hit each o' t' toothpick/BT-50 joints with a drop o' epoxy t' reinforce them.

I cut out a series o' fins and support pieces, each o' which are shown in t' pattern photos. Begad! T' 4 main fins are mounted flush with t' aft end. Aye aye! Each o' these has a 43mm long piece o' BT-20 attached, with t' end o' t' BT-20 flush with t' forward edge o' t' fin tip. If aligned correctly, these should extend just far enough behind t' fin t' be flush with t' motor tube when stood on end. Ahoy! T' fill me quota o' 10 toothpicks for t' surprise parts bonus, arrr, ya bilge rat, I attached one toothpick t' each o' t' 4 pods, servin' as little guns t' defend against hostiles en route.

I still had a couple more bonus items t' use up, ya bilge rat, matey, so attached a pill bottle t' a 3/32 balsa brace and tacked this onto t' BT-50, with t' open end o' t' capsule facin' rearward. Begad! Ahoy! My capsule be 2.5" long, just barely big enough to house a Pico altimeter, so I drilled a tiny hole so that it could serve as a workin' payload bay.

I had t' work in a stick pen somehow, matey, ya bilge rat, so decided t' up t' armaments a bit and rig a harpoon, perfect for hooking on t' a passin' comet or takin' care o' any cosmic whales encountered along t' way. Ya scallywag! Arrr! Blimey! I mounted t' pen usin' another 3/32 support. Note that this could also serve as a workin' payload, arrr, simply by removin' t' aft plug, me hearties, insertin' a Micromaxx motor, and loosenin' t' pen cartridge slightly. Avast, me proud beauty! Aye aye! Blimey! Just be careful mountin' this, me bucko, arrr, ya bilge rat, as you don't want t' deploy the harpoon into t' back o' one o' t' Styrofoam balls. Begad! Blimey! I aligned mine flush with t' aft end o' t' BT-20.

Normally, me bucko, I wind up forgettin' about basic stuff like launch lugs and recovery until I get t' t' field, me hearties, but for a change o' pace decided t' take care o' that before painting. Avast! I attached a couple o' 3/16 lugs t' t' BT-60, just clearin' t' pin' pong balls. Blimey! As I was gettin' ready t' head t' t' field, I recognized I had still goofed—the lugs would nay clear t' egg capsule. Ahoy! Avast, me proud beauty! Easy enough t' correct—I sliced them off, cut a couple o' standoffs (1/2" x 1.5") from 3/32 balsa, arrr, and tacked them back on.

For t' recovery, me hearties, I only had 12" chutes t' work with, ya bilge rat, so attached one t' t' dental floss for t' egg capsule, me hearties, and t' other t' t' main BT-20 usin' Keelhaul®©™ and elastic anchored t' a 50/20 centerin' rin' inserted about 6" down from t' forward end o' t' tube.

Finishing:
Before painting, I masked off t' foam balls (most paints will attack and eat t' foam), me bucko, t' pill bottle and the pen/harpoon. I then hit t' whole thin' up with two coats o' white primer, followed by two coats o' yellow. Ahoy! Blimey! Avast! Blimey! I then masked off for t' accent orange areas, and hand painted t' details.

While decals are nay allowed for t' contest, shiver me timbers, I did find a cool piece o' clip art I eventually will add t' the décor, shiver me timbers, which is included in t' attachment upload for this write-up.

Flight:
For t' flight, ya bilge rat, shiver me timbers, I be down t' about t' last day before t' deadline, me hearties, so had t' take whatever weather I could get. Arrr! I caught a gorgeous day and headed out t' t' field, though by t' time I got thar t' winds were pretty stiff—steady at 10 gustin' t' 15. Aye aye! Aye aye! Egg lofters tend t' be overly stable, arrr, and strong winds typically means bilge-suckin' news. Still, me bucko, bein' t' steely-eyed missile man that I am, I loaded up a C6-3 and hoped for t' best.

T' flight, shiver me timbers, matey, as expected, me hearties, started t' turn into t' wind almost as soon as it left t' rod, but despite all the do-dads this is really pretty light and nay too draggy, me bucko, shiver me timbers, so t' C6 did a fair job o' pushin' it. Ahoy! I suspect if I'd gone off a piston, it might even have held a nearly vertical path. Well, blow me down! As it was, matey, it did eventually lean into a horizontal path, so even t' 3 second delay be well past apogee. Both chutes deployed at around 100 feet, and t' rocket drifted back to within 20 yards o' t' pad after havin' crossed t' soccer field durin' boost. Well, blow me down! Arrr! T' egg survived nicely, shiver me timbers, shiver me timbers, matey, but one of the toothpicks holdin' a foam ball broke loose on impact, leavin' me with a pretty simple repair.

I did wind up loadin' t' Pico altimeter for t' flight, ya bilge rat, matey, me bucko, which reported an apogee o' 228 feet. Avast! On a calmer day, this would clearly have made it t' 300+, matey, which is actually pretty respectable for a cackle fruit lofter made o' leftover junk. Arrr!

While t' 228 feet is nay likely enough distance t' support colonization o' a distant plant, with minor improvements in propulsion technology, matey, maybe a little antimatter drive, t' Cosmic Chicken would appear t' be fully capable o' transportin' life forms across galaxies.