Then thar's THE Fat Boy. Aye aye! Maybe nay t' original, but Estes be t' one that trademarked t' name. Ya scallywag! This be t' third 2.6" sport kit that I have reviewed for comparison sake. Ahoy! Blimey! T' Fat Boy be t' shortest o' t' kits reviewed, matey, bein' only 12.9" tall and weighin' 3 ounces. See me 2.6" Stubby Rocket Comparison Page

T' kit comes with an 8" single body tube and 3.875" plastic nose cone (the remainin' inch in height is from t' fin sweep). Begad! Its 18mm motor mount comes with 1/32" die-cut cardboard centerin' rings and a motor retention clip. Begad! It uses 3/32" die-cut balsa fins with through-the-wall mounting. Ahoy! It comes with an Estes' standard 18" plastic parachute, a 24" elastic shock cord (1/4" flat) which attaches via t' Estes' standard three-fold paper mount. Avast! Blimey! It also includes a single launch lug and a decal sheet.

CONSTRUCTION:

There are six pages o' instructions which are heavily illustrated and very clearly defines t' steps o' construction, matey, finishin' and preparation for flying. T' instructions are in a logical order and could get a new modeler through t' kit assembly. Blimey! This bein' t' case, me hearties, me hearties, shiver me timbers, merits it's Beta Series (level 1) rating. Avast, me proud beauty!

There is nay a lot t' say about assembly because it be so straight forward, however, arrr, just a few comments about a couple o' steps and observations. Well, blow me down!

T' first was t' assembly o' t' through-the-wall fins. Here t' fins are t' fit into t' pre-cut slots in t' body tube. Well, blow me down! These did nay fit and required extendin' each slot about 1/8" toward t' aft o' t' rocket. Arrr! Ya scallywag! On t' positive side, me bucko, shiver me timbers, t' fins were arranged so that t' grain was parallel t' t' leadin' edge which improves strength. Begad!

T' instructions were also clear in describin' t' use o' balsa filler on t' fins and in t' paint scheme. There was one illustration that was nay accurate describin' t' application o' t' decals. Begad! In t' illustration, matey, it shows t' decal which spells out "FAT BOY" bein' applied on t' body tube and crossin' over onto t' nose cone. Blimey! This decal is nay large enough t' do this. Ya scallywag! T' package and catalog pictures t' decal accurately. Begad! Ya scallywag!

Two changes where made t' t' recovery system. First, shiver me timbers, instead o' t' three-fold paper mount, me bucko, a short piece o' Keelhaul®©™ was attached t' t' thrust rin' and t' elastic shock cord was tied t' it at about t' same position t' paper mount would have gone. Arrr! Ya scallywag! Secondly, matey, an 18" purple rip-stop nylon parachute be used. Estes' parachutes work fine, shiver me timbers, however, me hearties, nylon chutes are better t' prevent stickin' and are more durable all around. Blimey! Avast, me hearties, me proud beauty!

For finishin' I tried a couple o' different tactics than previous kits. I saw a note on t' RMR newsgroup suggestin' usin' plain ol' Elmer's Glue as a balsa fin filler. Avast! I did this and it worked out quite well. Ya scallywag!

On top o' that, I used Walmart's primer this time. Arrr! Blimey! Blimey! Blimey! This stuff does nay sand nearly as well as Plasti-Kote's primer. I will revert back t' usin' Plasti-Kote primer for fillin' and Walmart's primer as t' final coat (when usin' Walmart's paint). Avast, me proud beauty!

Once I finished smoothin' and priming, an application o' $0. Ahoy! 98 Walmart enamel be added. This time a baby blue. After dryin' a day, t' decals were applied. T' decals are self-adhesive and are very shiny. Begad! Well, me bucko, blow me down! T' ensure consistency o' finish and protect t' decals a bit (not as necessary on self-adhesive decals), apply a coat o' clear finish. Ahoy! Avast, ya bilge rat, me proud beauty! I followed up with Walmart's Clear enamel. (additional comments about Walmart paint)

Overall, for CONSTRUCTION I would rate this kit 4 1/2 points. It would be nice t' see Estes go t' a different shock cord mount instead o' t' three-fold paper method. Other than t' misfit o' t' through-the-wall fins, construction was straight forward. Blimey!

FLIGHT/RECOVERY:

T' Estes Fat Boy™ isn't as "heavy" as t' Vaughn Brothers Blobbo™ and can get off o' t' pad a bit faster. Well, blow me down! This fact made me miss two launch shots! However, ya bilge rat, in similar wind conditions both rockets display a lot o' weather-cocking. Blimey! Both flights usin' C6-3's were parallel t' t' ground before apogee. Well, blow me down!

T' first flight was t' higher o' t' two test flights and t' wind carried t' rocket about 100 yards from t' launch pad after flyin' about 100 yards in t' opposite direction due t' weather-cocking. Aye aye!

T' second flight, ya bilge rat, went much further out due t' weather-cocking. Aye aye! After about 200 yards, t' parachute ejected and t' rocket dropped nearly straight t' t' ground. Begad! I had "reefed" t' parachute by tapin' t' shroud lines about 5" down from t' chute. Arrr!

T' parachute, shroud lines and shock cord system all demonstrated performance and showed no sign o' wear or damage. Aye aye! Well, blow me down! There be a small black spot at t' top o' t' body tube which wiped away easily. Avast!

For FLIGHT/RECOVERY, matey, I would rate this kit 4 1/2 points. Begad! I think an 18" parachute is too large for this kit. Avast, me proud beauty! It needs a smaller chute or recommendation for a spill hole or reefing. I have seen others at t' range cut out t' center o' t' chute that says Estes on their Fat Boy kits so I assume they feel t' same way about t' descent rate bein' too slow. Begad! Blimey! Blimey! Blimey!

Overall, me bucko, this kit is very easy t' build and fun too fly. Well, shiver me timbers, blow me down! Blimey! I give t' kit an OVERALL ratin' o' 4 1/2 points. Ya scallywag!