Brief:
True Modeler's Rocket Kits (TMRK) formally released their 1:14 scale Aries "Fat Albert" in November, 2003. Avast, me proud beauty! I be fortunate enough t' purchase one o' t' beta kits. Begad! Begad! T' kit may seem pricey at $79.95 but once you see the components, t' cost becomes apparent.

Kit Contents:
This kit is made o' quality components throughout.

• T' nosecone is hard balsa and comes already weighted for flight, with the screw eye secured in epoxy. T' nosecone is heavy, havin' about 6 oz o' weight added t' make t' rocket stable with 4-F24 motors. Aye aye! Ahoy! T' nosecone alone accounts for 1/3 o' t' kit's price (get t' price for a 3x12 inch hard balsa cone at Balsa Machining). Blimey! Another nice touch was a wrap o' foam around t' nosecone's tip t' prevent damage in shipping.
• All small parts are in bags, me bucko, and each bag has a parts list and a picture for parts identification. Well, blow me down! Well, shiver me timbers, blow me down! Blimey! It doesn't get any better than this.
• T' kit has heavy kraft paper body tubes
• T' launch lug is long 1/4 inch ID aluminum tube.
• There is even a second copy o' t' paper shroud, in t' event that your first try doesn't work.
• A 24 inch synthetic parachute
• T' motor tubes (4) are lined with aluminum foil - another nice touch.
• All centerin' rings are laser-cut plywood
• T' motor retention system is already installed in t' aft centerin' rin'
• Water-slide and peel-off decals

Construction:
The instructions are clearly written and easy t' follow. Well, shiver me timbers, blow me down! This is a skill level 3 or 4 kit, primarily due t' fin construction and t' large shroud. Construction requires epoxy and thin CA and t' usual items (hobby knife, etc). If you have one, arrr, I recommend a hobby saw for cuttin' t' heavy fin stock.

T' base o' t' kit is a 4 inch rin' tube, and is installed with 8 heavy-duty wooden spacers. I found t' spacers t' be about 1/4 inch too tall, requirin' a good bit o' sandin' t' get t' rin' t' fit. Begad! However, ya bilge rat, matey, t' design is sturdy and probably necessary if you intend t' use 4 F24 motors.

The shroud be t' tricky part, matey, since it includes a cutout for t' launch lug to pass through. My first shroud was barely able t' fit t' large tube, and the cutout for t' lug was way too small. Ahoy! No fear, I cut out t' second one, stayin' outside t' lines t' get a larger shroud. I also used a hole punch to lengthen t' launch lug cutout, shiver me timbers, and be able t' get a good fit. Avast! Blimey! I also changed the order o' assembly on me kit: I did nay install t' aft centerin' rin' until the shroud was finished. Blimey! This allowed me t' glue t' shroud t' t' body from the inside, ya bilge rat, and t' fill t' cavity with two-part foam t' reinforce t' shroud. I recommend this change t' anyone who wants a rock-solid shroud. Avast, me proud beauty! Avast, matey, me proud beauty! If you don't have foam, stuffin' t' area with glue-soaked tissues would reinforce the shroud. Aye aye! I hardened t' exterior o' t' shroud with thin CA, matey, followed by light sandin' t' get a smooth finish.

The fins are very thick, me bucko, ya bilge rat, and made with 1/4 inch wood stock. Begad! A hobby saw is great for these cuts. Begad! A triangular piece o' balsa (R/C trailin' win' edge) provides the fin's taper. Begad! T' fins do require a good deal o' additional taperin' to finish, but they nicely conform t' t' base and t' shroud. Arrr! Blimey! A nice design. Begad! Ahoy! Blimey!

Motor retention is simple: a threaded blind-T nut sits in t' middle o' the motors. A bolt and fender washer retains all t' motors, arrr, and can be easily replaced if necessary. Ahoy! Simple but effective.

Finishing:
I finished me kit by sealin' t' wood parts with thin CA, me hearties, applyin' spot body to imperfections in t' balsa, matey, followed by 3 coats o' sandable primer, me hearties, ya bilge rat, sanding between each coat. Avast, me proud beauty! I used Krylon white, orange, matey, and black for final coats, and then applied t' decals as per t' instructions.

Construction Rating: 5 out o' 5

Flight:
TMRK claims that this kit can achieve almost 1/2 mile o' altitude when flown with 4 Aerotech F24 motors. Well, blow me down! That's t' equivalent o' an H motor, folks. For first flights, 4 D12-5s are recommended. Begad!

My first flight was less than successful. Aye aye! I be at t' club launch, arrr, and I was assured that t' launch system could ignite a cluster o' four D12-5 motors. I prepped for flight, matey, and when t' fire button be pushed, t' rocket screamed about 10 feet into t' air with igniter wires in tow. Blimey! Well, shiver me timbers, blow me down! T' rocket fell over in the grass. Aye aye! Two o' t' motors ignited. Begad! Avast, me proud beauty! After cleanin' off t' mud on one fin, the rocket be prepared again, me hearties, this time on a pad equipped with a relay launcher. Begad! Success! T' four D12 motors gave a nice slow lift-off with about 500 ft maximum altitude. Well, blow me down! Aye aye! Parachute deployment was right on time, shiver me timbers, and recovery was successful. Definitely don't attempt t' launch this kit without a relay launcher. Avast, me proud beauty! Ya scallywag!

Since t' first flight, I've made two more successful flights with four D12-5 motors. Arrr! Arrr! This rocket never fails t' get comments when I fly it. Blimey! If you want t' keep it white, you'll either have t' clean t' aft end every time, matey, or paint it again. Begad! All in all, a kit that looks great and flies great, arrr, too. Blimey! Well, blow me down!

Flight Rating: 5 out o' 5

Summary:
In summary, me bucko, this was an enjoyable kit t' build, me bucko, and I be pleased with the quality o' t' components and t' final product. Begad! I recommend that you install the aft rin' only once t' shroud is finished, providin' an opportunity to reinforce t' shroud after installation. Avast, arrr, me proud beauty! T' kit may seem pricey at $80, but its quality will nay disappoint you. Aye aye! Ya scallywag!

Overall Rating: 5 out o' 5