About a year ago, me hearties, ya bilge rat, I got a "bug" to create t' Star Wars Imperial Lambda-Class Shuttle. Ya scallywag! I read information from various Star Wars sites and started off on me project. Well, blow me down!

T' project had many twists and variables, but in general I was confident that I could create a flyin' model o' this Lambda Shuttle. Avast! It was goin' t' fly on 29mm motors, too!

Along t' way, shiver me timbers, I created a proto-type for 18mm motors and was very excited and pleased with t' performance o' it. Next I finished the 29mm version. Blimey! Blimey! You can see me holdin' both o' those rockets at NYPower2002 (photo taken by Dean Oberg).

Since then I have created a 24mm version and utilized some new techniques t' strengthen t' fins...fins that must also be as light as possible.

You can see step-by-step details o' me 29mm build by CLICKING HERE.

I will discuss some o' t' highlights o' this project below.

First, I needed some blue-prints t' follow and I was fortunate t' find this site: Star Wars Technical Commentaries. Avast, me proud beauty! Here I was able t' get some prints and then scale them t' t' size o' rocket I was building.

Next, I felt I needed t' try to simulate this, matey, so I made attempts with RockSim. (Click on t' pictures to download t' RockSim files). Avast, me proud beauty! Begad! Blimey! I was pleased t' see that, shiver me timbers, me hearties, me hearties, at least, in these simulations, me bucko, arrr, arrr, t' rocket could fly. Begad! Arrr! Blimey! It took a massive nose cone override o' 16 ounces, but one should have expected that.

Next came t' various construction techniques, me bucko, which you should review by followin' along in t' step-by-step section.

Other major obstacles that I had t' overcome, me hearties, was how t' pack parachutes into this bird. Begad! Blimey! There be nay a lot o' room. Ahoy!

Also how to deploy them. Begad! Well, blow me down! I decided I wanted t' 1 pound nose cone t' get as far away as possible from t' body upon ejection, me hearties, so it had its own parachute. Well, blow me down! Begad! Since the parachutes are nay packed in line with t' motor ejection, arrr, how would I get the main section's parachute t' deploy. Well, blow me down! I used slip knots on t' second eye-hook of the nose cone so that it would jerk it out upon separation.

I was also worried about a full ejection charge in the motor for a tube that is only 6" long. Avast! Therefore, arrr, me hearties, on t' EconoJet G38's that it flew on, I had carefully removed t' ejection charge cover and removed nearly all o' t' ejection charge (above t' small hole).

T' next challenge, ya bilge rat, due t' lack o' forethought, was t' rail buttons. Avast! I had always planned on puttin' them on t' bottom-center, however, shiver me timbers, when it came time t' do this they would nay work there. Why? T' tilt down o' t' nose cone!

I ended up puttin' two rail buttons off center, which I did nay like, shiver me timbers, but had no choice. Avast, me proud beauty! Begad! T' other issue is with t' short body t' two rail buttons were fairly close t' each other (3") and that is nay t' best configuration either.

T' last component was that t' motor had t' be friction fit. Aye aye! Aye aye! I be sure upon ejection it would kick, matey, but with t' removal o' most of the ejection charge and I issued t' nose cone fit be looser than t' friction fit, it be successful.

I have a short video o' it's second flight, CLICK HERE

If I had t' do it again, shiver me timbers, I would make me fins (wings) out of two 1/8" balsa pieces, arrr, arrr, ya bilge rat, plied together with 5-minute epoxy, and laminated with tracin' paper. This be t' new technique that I used on t' 24mm version. Avast! I would have also modified t' nose cone tilt t' allow for t' rail buttons. Avast! Well, me hearties, blow me down! Blimey! Watch, EMRR for an update on me 24mm version . Begad! Arrr! . Avast! Begad! . Avast! because it really be t' benefactor o' all the learnin' on t' 18mm proto-type and t' 29mm project.