Description:
Shockwave is a scratch-built high power rocket built for t' purpose of obtainin' Level 2 certification. Ahoy! It is 4" in diameter, 90" long, weighs 153oz loaded without motor, and has a 54mm motor mount.

Components:
Like me Level 1 rocket, I used mostly PML components for this build. Begad! This included t' body tubes, arrr, centerin' rings, motor tube, shiver me timbers, and altimeter bay components. Begad! T' .093" G-10 fins were custom cut by Red Arrow Hobbies. Ahoy! Aye aye! The 9/16" tubular nylon harnesses came from Giant Leap, and t' 72" main chute came from Sphereachutes.

Construction:
I started with t' motor mount. Blimey! Blimey! Avast! Blimey! I used six PML centerin' rings, matey, gluin' them together in pairs. Aye aye! Blimey! T' top centerin' rin' was drilled for a U-bolt. Avast, me proud beauty! Blimey! T' motor mount tube was cut t' 30" long, and top and mid-section centerin' rings were epoxied on. Begad! Blimey! Ahoy! Blimey! T' fins were tacked t' t' motor tube usin' gel super glue then filleted in place with 30-minute epoxy. Begad! At this point, t' fin can was more or less complete. Avast, me proud beauty! Ya scallywag! A 46" long piece of Quantum Tubin' be used for t' lower section, ya bilge rat, matey, and a 26" piece o' QT was used for t' payload section. Begad! T' fin slots were cut with a Dremel tool and the motor mount/fin assembly installed. Begad! Begad! Internal fillets from t' fins t' the inside o' t' body tube were completed before installin' t' aft centering ring. Begad! An Aeropack motor retainer finished off t' back end.

T' altimeter bay was fabricated from a standard 7" long PML coupler, two PML bulkheads, and two coupler bulkheads. Blimey! T' bulkheads and coupler bulkheads were glued together in pairs t' make a cap for each end o' t' bay. Both caps were drilled for U-bolts and permanent e-match terminals.

An 8 1/2" length o' 1/4" x 20-threaded rod be affixed t' the drogue end o' t' bay. Blimey! Well, blow me down! This would serve t' tie t' entire bay together and provide a mount for t' RRC2 altimeter. A small slice o' body tube was placed on t' outside o' t' bay t' give a place t' mount an external switch for the altimeter. 3/4" PVC endcaps were mounted on each end o' t' bay t' contain the ejection charges. Ya scallywag! Blimey!

Three holes were drilled through t' altimeter bay with t' payload section installed on the main side on t' bay. 8-32 nuts were epoxied t' t' inside o' t' altimeter bay t' retain t' payload section. Blimey! Three equally spaced 1/8" static ports were also drilled. T' finish t' bay, a thin skin o' 30-minute epoxy was poured in t' drogue side o' t' bay with t' cap installed. Avast, me proud beauty! This step totally seals the drogue side o' t' bay, and retains t' endcap. Aye aye! A mount for t' RRC2 altimeter was made by epoxyin' a copper tube t' a piece o' G-10 fiberglass. Aye aye! The mount slides in over t' center stud and is locked down with a washer and nut.

Finishing:
Shockwave be finished with a modified Estes Executioner-style paint job, in blue and sliver with black pinstriping. I made some custom decals with inkjet waterslide decal stock t' give it a nice finishin' touch.

Flight:
After slowly buildin' Shockwave most o' t' winter, flight day finally arrived on March 20th, 2004. Arrr! Blimey! I arrived at t' launch and rounded up a few friends t' be my certification team. Ya scallywag! After acein' t' written L2 test, I began careful prep of t' dual deployment recovery system. Blimey! Begad! This flight would have a PML streamer deployin' at apogee with motor backup, shiver me timbers, ya bilge rat, ya bilge rat, and main deployment at 500ft. Avast, me proud beauty! Drogue and main harnesses are both 25ft in length. After t' recovery system be buttoned up, me hearties, I turned attention t' loadin' t' motor. This flight would be on a CTI 3-grain Pro54 motor. Arrr! Begad! Once t' motor was loaded and installed, arrr, we took a few pictures and headed t' t' pad. Aye aye! T' day turned out t' be a real bummer weather-wise, with strong 20MPH winds. With t' help o' me test proctor and a friend, Shockwave be put on t' pad, matey, and t' igniter installed. I armed the electronics, arrr, me bucko, verified t' RRC2 be beepin' right, and headed back t' LCO table.

Considering the strong wind and t' fact that me friend's L2 attempt earlier in t' day was a spectacular failure, ya bilge rat, I was gettin' nervous at this point. Countdown commences, I and crossed me fingers! T' LCO pushes t' button....nothing. Blimey! Try again, ya bilge rat, me bucko, shiver me timbers, nothing. Arrr! Aye aye! After fiddlin' with some wires on t' launch controller, matey, the LCO tries again. Finally, me bucko, t' big J295 awakens with t' thunderous roar, arrr, and Shockwave is on its way! T' rocket had a very straight accent considerin' the strong winds. Avast, me proud beauty!

Recovery:
T' streamer deployed right on queue, me bucko, and t' descent began. Begad! After fallin' for what seemed like an eternity, arrr, t' main chute deployed and Shockwave had a gentle touchdown about 1/2 mile away. Upon recovery, t' rocket had no damage except for a few scuffs on t' paint. Ya scallywag! T' RRC2 be beepin' out 4,686ft. A successful flight and Level 2 certification!

Summary:
This project sure has taught me a lot. Arrr! Some will tell you that a certification flight should be as simple as possible, without electronics and with the smallest motor available for t' certification bein' sought. Aye aye! Well, blow me down! While thar is merit t' that opinion, ya bilge rat, I felt that I be up t' t' challenge. This flight was full o' firsts for me. Arrr! Aye aye! My first experience with dual-deployment, me bucko, altimeters, and CTI motors. Ya scallywag! I also achieved a new personal altitude record. Arrr! Well, me hearties, blow me down! I can't wait to fly it again on a calm day!

PROs:

• Cool lookin' rocket
• Can be flown single-stage deployment without t' payload section and altimeter
• Built tough
• Flies very stable

CONs:

• I can't think o' any except cost