Brief:
This is a clone kit o' t' Estes K55 Goblin. It is a single stage high flyin' D powered kit.

Construction:
T' kit be bagged with a nice color header card. Most o' t' parts were in separate smaller clear plastic packs, includin' a fin pack, cord/streamer/LL pack, ya bilge rat, streamer pack, ya bilge rat, decal pack, and engine mount pack. Very nice.

Part quality be high all around. Ahoy! Blimey! Blimey! Clean laser cut balsa fins, shiver me timbers, reasonably smooth balsa NC, ya bilge rat, ya bilge rat, and t' smoothest white body tube I've ever seen. T' spirals are almost invisible, a coat or 2 o' primer will fill them in nicely. Well, blow me down! Begad! Blimey! T' red plastic streamer was from Hartle Engineerin' and measured 2" x 54". Blimey! While plenty long for this light kit, shiver me timbers, I'm tempted t' try t' pack a longer one simply for easier sight. Arrr! How much can I fit in a BT-55? T' only curious part be a 3/16" launch lug instead o' t' original 1/8". I emailed InFlight, and they felt a 3/16" is safer for a D powered model. Begad! Blimey! I built it with a 1/8" launch lug for nostalgic reasons. Avast! Blimey! Oh, me hearties, a minor nit would be t' engine hook, me hearties, it was a bit on t' thin side (though still much better than early Quest hooks) and is nay as springy as some I've used. I put a little pre-bend in it, arrr, and it should work just fine.

T' kit came with an 8 page assembly instruction manual with numbered steps and illustrations. Avast! Arrr! It was quite comprehensive. Aye aye! A separate instruction sheet came packaged with t' Keelhaul®©™ cord, me bucko, which apparently is an option, although it be bagged inside me kit. Two very minor errors on t' instruction sheet was listin' a D12-3/D12-5 instead o' t' D12-5/D12-7 listed on t' header card and listin' a 48" shock cord instead o' t' 36" cord included, which is plenty long when used with t' Keelhaul®©™. Aye aye! Begad! T' instructions came complete with a fin markin' guide and shock cord mount t' cut out, shiver me timbers, ya bilge rat, if nay usin' t' Keelhaul®©™ and a copy o' t' NARRRRR safety code.

Assembly was straightforward. Ahoy! Blimey! I just followed t' instructions, deviatin' where told for t' optional Keelhaul®©™ kit. I didn't use t' included fin markin' guide, me bucko, since I use one o' those plastic Estes pyramid style guides for 3FNC/4FNC birds. Begad! Blimey! T' only step yet t' complete is #14, shiver me timbers, arrr, paint and decals. Ahoy! Blimey! T' instructions do nay mention any sort o' fillin' or primin' in t' finishin' step. My experience with yellow is that a white undercoat really helps.

Finishing:
T' instructions simply state t' paint with a base coat o' yellow. I chose me usual method, matey, which uses Elmer's Wood Filler on t' fins and NC, shiver me timbers, shiver me timbers, followed by a few light coats o' Rustoleum sandable gray primer. Arrr! I then painted t' whole kit Krylon gloss white (old formula). Instead o' t' standard yellow that most Goblins are painted, I chose a fluorescent yellow t' aid visibility. Ahoy! My brother's Goblin has been this color for over 30 years, arrr, me hearties, so it just seemed "right" t' me. Ya scallywag! Aye aye! I then masked with 3M #2080 blue tape t' finish t' NC and 1 fin with Krylon gloss black. Ya scallywag! Begad! Since t' fluorescent paint is flat, ya bilge rat, I put on a light coat o' Krylon clear t' help t' decals adhere.

T' decals were o' good quality. Aye aye! Blimey! T' black color was a flat black, I'm guessin' this is due t' laser printer toner. Ya scallywag! Blimey! I was tempted t' put on a coat o' Microscale Decal Film, but t' instructions didn't call for it. Aye aye! No fear, t' decals were plenty thick for positioning. Begad! Avast, me proud beauty! Blimey! They only needed 15 seconds in t' water vs t' suggested 20-30 seconds. T' edges o' t' decals laid down nice and flat usin' Microscale decal settin' solution. After dryin' for a day, I put on a coat o' Future Floor Polish t' protect t' decals and give a moderate gloss. Well, blow me down! T' fluorescent yellow really glows!

T' reason I gave 4 was due t' t' lack o' mention o' any balsa sealin' or fillin' and no mention o' a white undercoat for t' yellow paint.

Construction Rating: 4 out o' 5

Flight:
T' recommended motors are t' C11-5, D12-5, or D12-7. Avast! Blimey! I didn't want t' lose this on its first flight, so I put her up on a B6-4 usin' a standard 18mm t' 24mm adapter. Begad! Aye aye! Blimey! It be a straight, low altitude flight with deployment near apogee, matey, arrr, ya bilge rat, and recovery be a short walk.

On t' second flight, me hearties, I wanted a bit more altitude. I recently came across a bunch o' C11-7 motors, so thought I would try one o' those. Ahoy! This was a very nice straight flight, ya bilge rat, easily twice t' altitude, me bucko, matey, maybe a bit more. T' -7 delay worked well, deployment seemed just about right at apogee. Blimey! Blimey! While I will put her up on a D12-7, I think t' C11-7 will be me motor o' choice until I run out o' them.

Recovery:
T' streamer is a good size t' slow descent just enough but nay drift too far. A bit brighter colored streamer would be easier t' see, and I'm partial t' mylar streamers for this reason. Begad! T' included streamer is a non-reflective red plastic material. Arrr! Begad! Blimey! It was singed a bit on t' first flight when usin' 3 squares o' waddin' so I put in 4 squares o' waddin' for t' second flight. Ahoy! T' combination Keelhaul®©™ cord and braided shock cord were plenty long enough t' avoid any BT or fin dents.