AEON

Tim Breland's Descon-14 Entry

Talk about last minute, this thin' almost had t' fly with wet paint. ;)

My design is called t' AEON.

One definition o' Aeon is "an indefinitely long period o' time", me bucko, which is about how long this rocket might stay in t' air, indefinitely.

Stickin' with t' theme, t' Aeon burns a total o' 6 motors. It is clustered and staged, matey, me bucko, usin' 5 motors in t' booster and 1 in t' sustainer.

Construction is pretty simple. Avast! Arrr! A parts list and fin patterns are included in t' pdf file. Well, blow me down! Pretty much all o' me parts came from Fliskits, t' most unique bein' t' 5 motor cluster mount which has a central 24mm mount surrounded by 4 13mm mounts.

Sustainer:

Startin' with 2 BT70 tubes standard 17.5" in length, me hearties, arrr, arrr, I cut a 70mm long piece from 1 tube t' use as t' booster. Arrr! T' remainder o' that tube be coupled t' t' other tube t' make t' sustainer body, with a balsa nose cone on top.

T' sustainer got a standard 24mm motor mount, makin' sure t' put t' aft centerin' rin' about 1" from t' end t' allow room for t' stagin' coupler. Avast! This motor mount is 4" long with an engine block in place allowin' it t' hold and Estes E size motor.

T' sustainer fin pattern is in t' pdf file. 4 fins were cut from some high quality 1/8" balsa. Aye aye! Some may prefer thicker balsa or even plywood, but I wanted t' keep t' weight down. Aye aye! Avast! T' fins were mounted with t' root end about 10mm up from t' end o' t' body tube. Avast! This was done just for t' look o' a gap betwixt t' sustainer and booster fins.

A basic recovery system be installed; 4' piece o' 1/4" elastic attached with t' tri-fold method and t' a screw eye in t' nose cone.

An 18" mylar chute from Rockethead Rockets was me choice o' recovery.

Booster:

For t' booster I started by assemblin' t' 5 motor cluster mount. T' central tube included with t' kit was cut down t' 70mm long. Avast, me proud beauty! Arrr! This kit includes 4 centerin' rings. Aye aye! I left t' forward CR out due t' t' shorter central tube, arrr, and t' allow room for t' stagin' coupler. Ya scallywag! I also left out t' central motor block t' allow for staging. Aye aye! T' motor mount was then glued into t' 70mm piece o' BT that I cut earlier, flush with t' end. Aye aye! Ya scallywag! I then glued t' stagin' coupler into t' forward end. Ahoy! Again, 4 fins were cut from 1/8" balsa and attached t' t' booster (pdf file has pattern).

Finishing:

After priming, shiver me timbers, I applied a basecoat o' Krylon Metallic Silver. Begad! I then masked off t' fins and nose cone, and finished t' rest o' t' rocket with a candy green. Begad! Unfortunately, t' tape marked t' silver, and I may have t' repaint one day.

Flight report:

After t' paint dried, I prepped her for flight. Avast! I knew it would get dark soon, so I opted nay t' go fully loaded. Avast, me proud beauty! Well, blow me down! I went with a D12-0 surrounded by 4 A10-P's in t' booster, staged t' a C11-7 in t' sustainer. Ya scallywag! This added a good bit o' weight and I wasn't comfortable with t' Cg location. I then drilled 4 - 3/16" holes in t' base o' t' nose cone, added some BB's and secured with epoxy. This put t' Cg at about 17" from t' bottom, shiver me timbers, ya bilge rat, which is more than enough stability margin. Well, blow me down! Ya scallywag! So off t' fly. Begad! By now it's gettin' dark, me hearties, although nay as dark as t' pics show, but I'm still worried about recovery.

I set her up, matey, matey, push t' button, and whoosh, man was that fast. Arrr! Pics show nothing. Aye aye! Avast, me proud beauty! I obviously didn't get t' rocket in t' pics, because they're just black. Begad! Aye aye! I would guess it went about 1000', but it was probably lower, and I just couldn't see good. Well, I saw t' ejection, ya bilge rat, arrr, and thank goodness for mylar chutes. Avast, me proud beauty! Without t' shimmer from t' mylar I probably would have lost it. Avast, me proud beauty! It came down in t' field next t' me home about 300 feet away. Arrr! Begad! Luckily t' grass be cut over t' weekend and I be able t' find it pretty easily. Arrr! I can't wait t' launch it with an E9 in t' sustainer.