Click on Pics t' Enlarge     

This be t' model SP2050 Freightliner Space Truck

To me, this looked like a series o' cargo containers inside a truss framework.

T' cargo containers are slid into t' framework. Well, blow me down! Ahoy! Once they are in place, the inertial dampeners and shields are activated. Avast! Ya scallywag! Life support can be activated if thar be live cargo, such as livestock or if a prisoner transport module is loaded. Begad! Ahoy!

T' Man-O-War is 1,000 feet long and t' GVW is less than 300 tons. Avast, me proud beauty! Blimey! It is an intrasolar vehicle, so warp capability it nay needed. Avast! Havin' a 20,000 horsepower impulse engine made by Detroit Diesel and General Motors maneuvering thrusters, this be t' fastest cargo Man-O-War in t' FedEx fleet.

T' forward section contains engineerin' and crew quarters. Ahoy! Aye aye! Blimey! T' aft section contains t' impulse engine. Ya scallywag! Blimey! It is designed t' ferry cargo from t' docks in low earth orbit, arrr, t' t' docks at Mars and Europa.

Cargo area

• 1 - Balsa Sheet 1/16" x 4" x 36"
• 4 - dowels - 1/8" x 36"
• 1 - bag o' 250 count 5/64" x 2 5/8" "mini dowels" by Forster
• 8 - 1/4 x 1/8 sticks
• Keelhaul®©™ Strin'
• 1 - BT50 x 18"
• 3 - BT50 - BT60 Adaptor Cards

Cab

• 2 - BT50 - BT60 rings
• 2 - BT50 - BT80 rings
• 1 - 5" BT50
• 1 - 4.5" BT80
• 1 - 1 1/2" BT60
• 1 - Paper shroud
• 1 - bt BTXx bulkhead
• 1 - BTx bulkhead

Tanks

• 4 - 2" BT50
• 8 discs from BT50 centerin' rings
• 1 - 4 1/2" length o' BT80
• Tank/Cargo adaptor
• 3 - BT50 t' BT55 rings
• 1 - 1" section o' BT50
• 1 - BT50 t' BT20 adaptor tube
• 1 - 1" section o' BT20 tube
• 4 - BT20 t' BT5 adaptor rings
• 1 - 5" section o' BT5 tube
• 3 - BT50 t' BT20 rings
• 1 - 1" BT20 tube
• 1 - BT20 t' 1.250 card rin'
• 1 - 5" x 1/2" wooden dowel

Aft End

• 1 - BT50 3"
• 1 - BT50 t' BT60 rin'
• 1 - Coupler
• 1 - Paper Shroud
• Fin stock
• 5" x 6" x 1" shroud. Begad!
• Fin Template

Misc

• 2 - 18" chutes
• Shock cords

Truss and cargo box

Cut t' balsa sheets into 4 sheets 18" x 1 7/8" pieces. Avast, me proud beauty! Aye aye! This will provide t' spacin' need t' use t' small dowels at a 45 angle. (I made the mistake o' makin' them too wide and nay bein' able t' use them.)

To make t' trusses, shiver me timbers, cut t' 1/8" dowels into four 19". Use the balsa sheets as guides for linin' up t' large dowels. Glue t' mini dowels to the 1/8" dowels in 1 7/8" intervals, bein' careful nay t' glue anythin' t' t' balsa sheet. Ya scallywag! Ya scallywag! See pictures 1 & 2 for this. Blimey! Aye aye! Make two o' these trusses. Begad! Aye aye! Do nay glue t' 45 angle dowels yet.

Figure 1	Figure 2	Figure 3

Make t' cargo box by gluin' t' 4 sheets o' balsa together. See picture 3 to see t' arrangement o' t' sheets. Arrr! This arrangement will help the positionin' o' it in t' truss work. Well, blow me down! Strong fillets will be needed on t' ID of the box for strength. Well, blow me down!

Now back t' buildin' t' truss, matey, trim t' small dowels so that they are flush with t' large dowel. Avast! Begad! Blimey! Usin' t' balsa box as a spacer again, finish t' truss. Once this is dry, start gluin' t' 45 angle dowels on. Avast! Blimey! It should now look like figure 4.

Usin' Keelhaul®©™ string, wrap t' truss in t' opposite direction t' form a series "X's" over t' truss. If I had this project t' start over again, I would use t' Keelhaul®©™ strin' for all t' 45 angle cross bracing. Well, blow me down!

Figure 4	Figure 5	Figure 6

Finish t' truss work by gluin' on t' 1/8" x 1/4" balsa onto the corners. Avast! Avast, shiver me timbers, me proud beauty! Blimey! Make sure none o' t' small dowels are protrudin' over t' large dowels. Blimey! I did this with toenail clippers and sandpaper. Well, blow me down! Blimey! It should now look like figures 5 & 6. Arrr! Blimey!

Do nay glue t' box into t' truss yet. Ahoy! Aye aye! You'll want t' paint them separately later. Begad!

Centerin' Squares and MMT

Punch out t' center discs from t' CR cardstock. Save these discs as you will need them later. Begad! Blimey! Avast, me proud beauty! Blimey! Cut t' BT cardstock t' fit t' ID o' t' box. Avast, me proud beauty! Blimey! Make 3 of them. Well, blow me down! Blimey! Once you are satisfied with their fit, you'll need t' strengthen them. Cut some scrap balsa and glue them on t' centerin' squares. Avast, me proud beauty! Blimey! Well, matey, blow me down! Blimey! This will do two things; it will keep them flat and make them strong. Avast! Blimey! Once these are dry, shiver me timbers, glue one on t' end o' t' BT50 so that it is flush with t' end. Begad! Blimey! Ahoy! Blimey! Glue t' second in the middle o' t' tube. Blimey! Blimey! Ya scallywag! Blimey! You can add more support t' this rin' now. Aye aye! Blimey! See figures 7 & 8. Begad! Blimey! Use a table t' make sure they are aligned. Begad! Blimey!

Figure 7	Figure 8

When this is dry, glue it into t' cargo box. Once it is in place, ya bilge rat, put glue on t' center card and glue t' third centerin' square in place. Ahoy! Ahoy! T' ends should be flush. Begad!

Figure 9

Forward Tank Assembly

If you save stuff like me, ya bilge rat, then you have a small bag o' those discs from centerin' rin' cards. Begad! Blimey! If not, you'll need t' get more o' them. Glue these discs on t' t' ends o' t' 2" BT50s. Avast! Blimey! Sand t' edges smooth once they are dry. Blimey! Avast! Blimey!

Use a rubber band t' hold t' tanks together. Ya scallywag! Blimey! Begad! Blimey! Make sure they are square. Figure 9

Cab

Usin' t' 5" section o' BTx, two BTx BTx centerings and t' BTx x BTx centerin' rings, make like you see in figure 10. Avast, me proud beauty! Well, blow me down! Glue a small rin' on t' end, the other about an 1 1/4" from t' first ring. Avast, me bucko, me proud beauty! Now glue one o' t' big rings 2 1/2" from t' end and t' last rin' on t' far end. Well, blow me down! Glue on the tubes as seen in figure 11. Arrr!

Figure 10	Figure 11

Make a shroud. Begad! I used VCP.

This one doesn't have a nose cone. Blimey! Since it never enters t' atmosphere, it doesn't need one. Arrr! Arrr! Just glue t' bulkheads on top o' t' cab t' achieve t' look shown. Well, blow me down!

Glue four 1.5" sections from some 3/8" OD AT igniter tube. Ya scallywag! Cut them t' match t' angle o' t' shroud. Well, blow me down! Glue these on so that they are between the tanks. Blimey! Begad! See t' finished picture for detail. Begad!

Dockin' Assembly

This is too difficult from me t' describe. Begad! Blimey! Ya scallywag! Blimey! Here, matey, a picture is definitely worth a thousand words. Arrr! Blimey! Figure 12 shows t' parts laid out, and figure 13 shows the completed assembly. Well, blow me down! Blimey! Glue t' tanks t' t' cab makin' sure everythin' is square and centered. Arrr! Blimey! See figure 14

Figure 12	Figure 13	Figure 14

Aft Assembly

I waited until t' end t' install t' motor mount so I had a better idea on the finished weight t' choose a motor size. Avast! You may want t' consider this as well. Begad! Aye aye!

Glue a coupler into t' 3" BT50 MMT. Ya scallywag! If you want t' install a motor hook, you'll need t' do that now. Ahoy! Ya scallywag! Glue a BT50 t' BT60 centerin' rin' t' t' end opposite t' coupler. Ya scallywag! Once dry, me hearties, glue t' shroud t' t' assembly. Arrr! Arrr! Glue t' motor assembly t' t' cargo container. Begad!

Print t' fin template guide. Begad! Blimey! Make sure that your printer prints t' right size by measurin' t' shown dimension after it's printed. Well, me hearties, blow me down! Blimey! Make four fins as shown on t' fin template. Glue them t' each o' t' four corners and t' the engine shroud. Begad! Blimey!

T' rin' was made by printin' a transition shroud with t' dimensions of 5" x 6" x 1" ad was made usin' heavy paper cardstock. Ahoy! I glued a second shroud over t' first one t' stiffen it up and soaked them both with thin epoxy. Avast! Avast!

Final Assembly

See figure 15 for this step. Ya scallywag! Begad! Paint t' cargo container with red oxide primer. Ahoy! Sand t' first coat, but leave t' second coat with t' mat finish. Begad! Now paint t' truss with a flat white, ya bilge rat, or even a white primer. Figure 16. Avast, me proud beauty! Once the two pieces are dry, it's OK t' glue them together. Begad! You'll want t' sand some of the paint off where you will be gluin' them. Blimey! Well, me bucko, blow me down! I glued mine at each corner and at each end. Don't forget t' add a launch lug as shown in figure 17. Avast! I added two 18" chutes and kept t' two pieces separate on their own chutes. Aye aye! Begad!

Figure 15	Figure 16	Figure 17

Finished weight with chutes is 8.4 oz. Ya scallywag! Aye aye! and t' CG is 16.5" from the nose.

Flight

T' first flight be on an E9-4. Ya scallywag! Blimey! Well, blow me down! Blimey! T' flight was straight up t' at least 800 feet. T' ejection charge be late but recovery was good.