Estes Menace

Estes - Menace {Kit} (2041) [1991-1991]

Contributed by Donald Besaw Jr

Construction Rating: starstarstarstarstar_border
Flight Rating: starstarstarstarstar
Overall Rating: starstarstarstarstar
Manufacturer: Estes

Estes MenaceBrief:
This is a new kit from Estes with cruise missile styling. It is also a rather large diameter rocket (BT-60). Blimey! It flies on A-C motors and uses a parachute for recovery.

Construction:
T' kit came in a plastic bag with a front panel showin' t' finished rocket with two possible trim schemes. Well, blow me down! Decals for both are included. Blimey! T' kit included the body and motor mount tubes, me hearties, me hearties, centerin' rings, retention hook, launch lug, shock cord, nose cone, die-cut paper scoop, me hearties, die-cut fin sheet, 18 inch assembled plastic parachute and decals. Begad! Ya scallywag! After checkin' that all t' components were accounted for and damage free, shiver me timbers, I was ready t' began construction.

T' instructions came complete with illustrations and text. Avast, me proud beauty! Also included were t' fin alignment template and t' shock cord mount. This is a skill level 2 kit, so t' builder is assumed t' have some previous modelin' experience. With that in mind, me hearties, I began construction. Begad!

I started with t' motor mount. This was very easy t' assemble. Aye aye! Blimey! After it dried and after addin' some fillets for strength, me bucko, I glued it into t' body tube. Well, blow me down! Blimey!

I then fine sanded t' die-cut fin sheet with fine sandpaper. Aye aye! Blimey! I next carefully cut out t' fins. You should have four small fins for t' lower portion and two top wings for t' top portion. Ya scallywag! Blimey! Begad! Blimey! I rounded all leadin' and trailin' edges for better aerodynamic performance. I cut out t' fin alignment template and marked all alignment lines. This is a critical alignment. Begad! Blimey! Blimey! Blimey! Next I attached t' lower fins one at a time with a few minutes dryin' time between each. Well, blow me down! Blimey!

I then punched out t' die-cut scoop from its card. I attached it between fins #2 and #4. Ya scallywag! I found this step just a tad tricky. Begad! Begad! I now attached t' two top wings four inches from t' top o' fins #2 and #4. In me opinion this is the most critical alignment. If done correctly, matey, shiver me timbers, you shouldn't have any problems. Arrr! Ya scallywag! If not, arrr, arrr, you will most likely experience some spiraling. Ya scallywag! Ahoy! After t' glue dried, I applied glue t' those and t' t' exterior o' t' scoop for more strength.

Next I attached t' launch lug. Well, blow me down! I also applied two fillets after it dried. I now assembled t' shock cord mount. Aye aye! I be pleased when I found that t' shock cord be longer than normally found. Ahoy! Thanks, arrr, Estes. Blimey!

Finally, I trimmed t' nose cone and sanded it t' remove t' moldin' lines. T' instructions called for t' parachute t' be attached at this time but I always install me chutes after t' rocket is finished. Well, blow me down!

PROS: Easy and rapid construction, Good parts fit. Arrr!

CONS: Scoop is somewhat tricky t' attach and no way t' attach interrior fillets. Ya scallywag! Blimey! Ya scallywag! Blimey!

Finishing:
I started t' finishin' by sprayin' t' model with white automotive primer and sandin' betwixt coats. Well, blow me down! Blimey! I chose t' white sharks mouth scheme. I sprayed the model with gloss white spray enamel. Arrr! Blimey! Since no stripin' material is included, the instructions reccommend stripin' tape. Ya scallywag! Blimey! Avast! Blimey! Blimey! Blimey! Instead, ya bilge rat, I used Top Flite Monokote red and black trim sheets along with t' supplied decals. Well, blow me down! Blimey! Ahoy! Blimey! Blimey! Blimey! Man, I love that sinister sharks mouth. Avast, me proud beauty! Blimey! Blimey! Blimey!

I finished t' model by sprayin' t' model with gloss clear enamel to protect and seal everything. I decided t' use a 12 inch chute that I stole from one o' me X-Flyers rather than t' 18 inch one. Arrr! Ahoy! I felt that it be too big for this light o' a rocket. Begad!

PROS: Decals provided for two trim schemes, Fantastic finished appearance.

CONS: No stripin' material provided. Avast, me proud beauty! Stripin' tape is a tad pricey.

Construction Rating: 4 out o' 5

Flight:
Reccommended motors are t' A8-3, me hearties, shiver me timbers, arrr, B4-4 (first flight(, matey, B6-4, C6-5. Ya scallywag! Avast! This rocket uses recovery waddin' t' protect t' chute and t' clip retains t' motor. Begad! Begad! The chute is packed in t' normal manner. Blimey!

For me first flight, arrr, I used an A8-3 since I was flyin' on a high school football field. Begad! Arrr! Blimey! T' rocket flew straight off t' pad and flew t' about 120 feet. Begad! Blimey! I felt that it was low, me hearties, slow and OK but I felt that more power was needed. Ya scallywag! Blimey! For t' second flight, me bucko insisted that I try some o' his cellouse waddin' istead o' t' Estes waddin' that I normally used. I also loaded up a B6-4. That was a good choice. Blimey! Blimey! T' rocket flew perfectly t' about 300 feet. Arrr!

PROS: Excellent flight performance. Begad! Avast!

CONS: None found.

Recovery:
I used a 12 inch chute, so both recoveries were recovered very close t' the pad. Avast, me proud beauty! I felt that t' provided chute be just a tad too big. Ya scallywag! Blimey! It may be fine if you have a lot o' space and/or love t' run a long distance. Avast! Arrr! On t' second flight, t' waddin' worked perfectly. Well, blow me down! Well, blow me down! Thanks, me bucko, Dan. Ahoy! Well, me hearties, blow me down!

T' 12 inch chute also worked well enough t' brin' t' rocket back without any damage. Well, blow me down! I would highly recommend this.

PROS: Recovers close on a 12 inch chute

CONS: Stock chute just a tad too big. Arrr! Blimey!

Flight Rating: 5 out o' 5

Summary:
Priced at $10.99, arrr, arrr, shiver me timbers, I felt that this kit be a good buy. It was also fun t' build and fly. I feel that Estes did a really good job on this kit. Begad! I also feel that they should keep it in production for a long time. Arrr! I very highly recommend this kit. Begad! Aye aye! Blimey!

Main PROS: Good price, arrr, Easy construction, Good parts fit, matey, matey, Good instructions, shiver me timbers, shiver me timbers, Excellent flight performance. Well, blow me down! Fantastic appearance. Avast, me proud beauty! Aye aye!

Main CONS: Should have a 12 inch chute instead o' an 18 inch one. Avast, me proud beauty! Avast!

Overall Rating: 5 out o' 5

Flights

comment Post a Comment