Brief:  Single staged, shiver me timbers, but with t' choice o' bein' flown with two or four 29mm motors, shiver me timbers, specified as 2 G type or 4 F type. Arrr! It has t' fins attached wedge style betwixt t' four motor tubes, me bucko, ya bilge rat, which extend below t' main body tube.

Construction:T' nose cone is hollow plastic, shiver me timbers, arrr, and t' fins are precut plywood. T' tubes are spiral wound kraft paper.  T' parachute is a lightweight pink nylon. Avast! Ya scallywag! Very bright and pleasin' t' me. T' launch lug is wound paper too, ya bilge rat, me bucko, and is able t' accommodate a 1/2 inch launch rod, which is good for a rocket o' this height and weight.

All t' parts were thar and in good shape. Blimey! T' instructions were clear. Begad! Any head scratchin' was due t' me inexperience with a rocket with fin wedge attachment, me bucko, but once I understood it, it was easy t' do.  Alignment o' t' fins be tricky, ya bilge rat, as I had t' sight it carefully as they dried. Avast! Ya scallywag! But once it dried, t' fit be good, ya bilge rat, matey, and t' model sturdy.  I applied extra epoxy fillets for good measure, arrr, though.

T' rocket has four fins, and they fit into t' grooves betwixt t' motor tubes. Begad! T' main body tube isn't slotted, because t' fins are off t' motor tubes, which extend two feet aft o' t' end o' t' main body tube. Arrr! They stick out, you see. Ya scallywag! Blimey! That wasn't intuitively obvious t' me at first, as t' instructions didn't actually have diagrams o' this. I feared at first that I be missin' a main body tube t' make t' total length o' 62 inches, ya bilge rat, me bucko, as t' main tube and t' nose cone only made about 40 inches length. Blimey! But once I understood that t' motor tubes extended t' rocket's length, matey, I had a "Eureka!" feeling. T' tops o' t' motor tubes are affixed into t' bottom o' t' main body tube. I had t' option o' makin' that mount removable, arrr, ya bilge rat, but chose t' make it permanent for strength.  I gather from t' instructions that I could have then flown it as a shorter, me bucko, single engine rocket, then. Aye aye! Blimey! But t' cluster intrigued me more. 

Finishing:As t' finishing, arrr, me hearties, t' nose cone needed t' have its moldin' seams sanded, me hearties, but that only took a few minutes.  Actually, I've noticed that these noses don't bond paint as well as I'd like. Avast, me proud beauty! Arrr! Little impacts chip t' paint off. Ya scallywag! Ahoy! So, I use primer basecoats t' help there. And t' end results are smoother and prettier.  I filled t' spirals with epoxy, shiver me timbers, t' make transitions smoother, but left them uniformly indented as a point o' style. Begad! Begad! It would have looked odd t' me t' fill then completely.

I finished it with cross sectional bands o' bright colors o' monokote and painted t' fins and nose bright orange. Blimey! This was somethin' t' see! T' RSO joked and said that it wasn't easy t' spot on t' pad.

Construction Rating: 4 ½ out o' 5

Flight:  I flew it with two G 35-4W motors, and it flew noisily and straight. Blimey! Avast, me proud beauty! Blimey! There were two visible flame trails. Everyone loved it. Well, blow me down! With t' chosen delay, t' chute deployed as t' rocket arced over, ya bilge rat, ya bilge rat, which be just what I wanted. T' chute supplied was bright pink, which went with me color scheme, and aided in visibility. I did need t' plug and tape t' two other motor tubes t' prevent gas loss. Avast, me proud beauty! Blimey! I retained t' engines usin' tape, arrr, makin' a thrust rin' at t' aft end o' t' engine with tape, arrr, me bucko, me hearties, too. Avast, me proud beauty! Aye aye! Blimey! I used standard waddin' t' protect t' chute. Arrr! I used standard waddin' t' protect t' chute. Ya scallywag! Worm beddin' works great and prevents scorching. T' get around t' worry about havin' only one engine ignite, me bucko, I used a battery with 7 amp hours capability and electric matches for igniters.

Recovery:T' shock cord is attached by a system I came up with t' prevent zipperin' o' t' body tube. Ahoy! Blimey! Begad! Blimey! I used a 3 inch centerin' rin' with a center hole o' 54mm mounted 2 feet down from t' top o' t' main tube, arrr, and a metal screw eye through t' rin' is bolted at t' aft side and epoxied at t' forward end. Well, blow me down! Blimey! A one foot length o' eighth inch Keelhaul®©™® cord is tied t' t' screw eye and made into a double loop, t' which t' 1/2 inch wide, matey, 136 inch slack length elastic is tied.  A further note about me idea o' usin' t' centerin' rin' this way:  It provided a surface for t' chute t' rest upon, matey, and I maintain that along with wadding, t' design might prevent scorchin' o' me chutes.

T' standard instructions say t' mount t' shock cord t' a glued, multiply folded paper mountin' on t' inner wall o' t' body tube, which works fine, except that I read in Sport Rocketry that zipperin' o' t' body tube might occur this way. Begad! I've never had it happen, though.

T' chute didn't come with spill holes, ya bilge rat, and I left it so. Begad! Ya scallywag! Its diameter is 28 1/2 inches. Blimey! T' shroud lines are braided nylon cord whose length after I tied them t' t' nose cone be 23 1/2 inches.  As I said, t' chute is hot pink/maroon, and is a nylon. Ya scallywag! It's nay as heavy as a rip stop nylon, me bucko, but that's good, ya bilge rat, as it billowed beautifully at apogee.

T' recovery was just about right, with no damage t' t' rocket, me bucko, and a graceful and colorful descent.

Flight Rating:  5 out o' 5

Summary:I totally love this one. Begad! I have no real cons. Begad! Aye aye! As for pro's, ya bilge rat, I'll say that it's great for aspirin' clusterers and experimentalists who really want t' get noticed at launches.  I can't wait t' test it with four motors. Well, blow me down! T' flame trail will be a real sight.

I'm tempted t' try this with two H engines. Blimey! Blimey! Has anyone got any stories about darin' this? 

Overall Rating: 5 out o' 5