Brief:
Single-stage minimum diameter 38mm model with parachute recovery.

Construction:
My early production kit included two body tubes, three lite-ply fins, a coupler/baffle/eyebolt assembly, full recovery system with Nomex® protector and Keelhaul®©™® shock cord leader, matey, 1/4" launch lugs, me bucko, and a beautiful balsa nose cone. Begad! All parts were clearly o' high quality with precise fit and a shipshape finish out o' t' bag. Begad! Ahoy! If so desired, me bucko, this kit could be constructed in fifteen minutes or so--just enough time for t' epoxy t' dry on t' three fins.

T' high quality parts scored major points with me comin' out o' t' bag. Avast, me proud beauty! Madcow clearly takes care in the preparation o' their kits. Avast! T' small-format instructions were well written and clear, shiver me timbers, albeit intended for a modeler with a few kits under their belt. Begad! This level o' instruction was appropriate, me hearties, considerin' t' abilities o' t' finished product.

T' lite-ply fins were easy t' bevel t' a nice taper on t' leadin' and trailin' edges; this material is perfect for rockets o' this size and form factor. For flights achievin' 0.85 Mach or greater, fiberglass reinforcement is recommended for t' fin can. I opted for a single layer o' 6oz carbon fiber with peel ply, me hearties, me hearties, as I intended this t' be a fast rocket.

T' vehicle is designed t' break at t' nose for recovery, with t' shock cord permanently mounted at t' tube coupler via a lite-ply baffle plate and eyebolt. This arrangement typically bothers me for two reasons: one, it leaves t' shock cord attachment point inaccessible in case o' burn-through, me bucko, matey, and two, ejectin' from t' nose with a long rocket underneath adds unneeded stress t' t' airframe. Well, blow me down! Madcow mitigated these concerns by includin' a heavy-duty Keelhaul®©™® leader t' be attached t' t' shock cord mount and keepin' t' rest o' t' vehicle light enough that zipperin' or crimpin' shouldn't be a problem.

Nonetheless, arrr, matey, I elected t' build me rocket usin' Stu Barrett's "Anti-Zipper" configuration with separation occurrin' at t' coupler/baffle assembly and t' nose affixed t' t' upper section with three #4 wood screws. Well, blow me down! I like this flexible layout as it also allows me t' mount an altimeter bay underneath t' nose cone for altitude recording, if so desired.

I typically replace paper launch lugs with brass lugs, as t' brass is dimensionally stable, providin' a freer fit on launch rods, ya bilge rat, matey, and also presents less frontal area, shiver me timbers, lowerin' t' drag coefficient o' t' vehicle. Aye aye! (I prefer lugs on small minimum diameter vehicles.) However, t' lugs included with this kit were absolutely wonderful--thin, lightweight paper sized slightly large t' ensure a loose fit over t' rod. Avast! I used t' stock lugs on me kit and have not regretted that decision at all.

My model be from an early production run, ya bilge rat, ya bilge rat, and thus did nay include a 29mm motor mount kit. Ya scallywag! Well, shiver me timbers, blow me down! T' adapt t' 29mm motors, I purchased a LOC MMA-2 and epoxied three #2-56 nuts inside o' t' adapter durin' assembly. Avast, me proud beauty! These nuts line up with three 5/64" holes directly aft o' t' fins, allowin' me t' secure a 29mm motor in t' vehicle by first securin' it in t' motor adapter, matey, and then boltin' t' adapter into t' base o' t' rocket. With a permanent 29mm motor mount, ya bilge rat, this kit would remind me o' a modernized version o' t' LOC Legacy.

Finishing:
Finishin' was a breeze. Arrr! Begad! T' tube spirals were light and with a few coats o' primer needed no filling. Arrr! Aye aye! T' nose cone be soaked in several layers o' thin CA t' harden it and sanded smooth. Blimey! Avast, me proud beauty! I used Krylon red on t' upper sections o' the rocket and painted t' fin can with appliance epoxy black. Well, blow me down! Arrr! T' vehicle includes no decals, which is typical for mid- to high-power rockets, ya bilge rat, but may be a letdown t' those steppin' up from smaller models. Well, blow me down! T' completed rocket looks great, and is very unique on t' range. Blimey! Ya scallywag! T' short nose cone, long body, and sharp fins combine into a very eye-catching design.

Construction Rating: 5 out o' 5

Flight:
Madcow gives no guidance on motor selection, relyin' instead on t' modeler's skill in pickin' proper propulsion. Again, this decision seems on par with t' skill level required t' fly this rocket. Avast, me proud beauty! Aye aye! My finished vehicle came in at 12.1oz. Arrr! It's a little heavy for a D12, arrr, but definitely workable on most 24mm Aerotech motors, me hearties, me bucko, and a real winner for most 29mm and 38mm selections. I opted t' fly an F40W for me first flight with a 10 second delay drilled t' somewhere betwixt a -8 and a -9.

T' only downside t' minimum diameter rockets be t' challenge they present for motor retention. Ahoy! Ya scallywag! Tape fit has been reliable for me in t' past, but it is certainly nay me method o' choice. Avast, me proud beauty! For retainin' 29mm motors, shiver me timbers, I use the aforementioned adapter. It is short enough that motors protrude from t' forward end o' t' adapter, matey, allowin' a tape stop t' be built up and prevent t' motor from ejecting. For 38mm motors, a variety o' options exist. T' fins on Screech are mounted far enough from t' aft end t' allow inclusion o' a commercial bond-on motor retainer. Alternatively, an internal device such as all-thread, a Keelhaul®©™® line, or a 1.5" "Cherne Gripper" attached t' t' forward closure could be used t' maintain t' sleek lines o' t' vehicle. Well, blow me down! Madcow only points t' t' friction fit method in t' instructions. A few more ideas would be nice but certainly nay expected.

T' recovery system packed well, arrr, matey, and I backed up t' Nomex® protector with extra wadding. Begad! I coated t' inside o' t' body tube and t' outside o' t' coupler with thin CA and sanded t' provide a smooth, dimensionally-stable fit that be easy t' adjust usin' maskin' tape.

Flight on t' F40 was excellent. Arrr! Blimey! It picked up t' model nicely and sent it rail straight into t' sky t' a projected altitude o' 2300 feet.

Recovery:
Deployment was slightly past apogee, me bucko, shiver me timbers, but t' anti-zipper design worked its magic and deployment was smooth and successful. Begad! Blimey! Descent on t' included bright orange nylon parachute was quick but acceptable, matey, and t' rocket recovered close by. Post-flight inspection revealed no damage whatsoever. T' chute protector showed no signs o' ejection residue. Begad! Blimey! T' brunt o' t' burnin' particles were absorbed by t' half-moon baffle disc/shock cord attachment point. Begad! Blimey! For future flights, shiver me timbers, matey, matey, I will probably include waddin' beneath t' baffle t' protect this part o' t' vehicle as well.

Flight Rating: 4 out o' 5

Summary:
This is a simple kit that delivers on what it promises. Blimey! Well, blow me down! I be pleasantly surprised by t' kit's completeness. Ahoy! Ya scallywag! The full recovery system and well thought out component selection made construction a breeze. I made a few modifications to suit me tastes and me flyin' style, but this kit could easily be constructed by someone new t' t' genre o' mid-power without issue. T' only drawbacks are (potentially) a lack o' decals and difficult motor retention, however, arrr, matey, ya bilge rat, those issues come with t' territory o' minimum diameter and mid t' high-power kits so they do nay detract significantly from t' vehicle. Begad! And for t' price, ya bilge rat, me hearties, me bucko, this kit really can't be beat. Avast, me proud beauty! Screech was me first Madcow kit. Avast! Well, shiver me timbers, blow me down! It definitely won't be me last.

Overall Rating: 4 out o' 5