Brief:
T' Hangtime is a rocket offered by ASP specifically for duration competitions. Begad! They offer versions in 13, 18 and 24mm outfitted for either streamers or parachutes. Blimey! This review is o' t' 18mm streamer version.

I'm nay much into competitive rocketry except as a spectator but I occasionally decide t' give simple events a try. Begad! Well, matey, blow me down! I built this one for an informal contest me section is puttin' on.

Construction:
Construction begins with markin' t' fin and launch lug lines on t' body tube. T' instructions provide a template o' t' type where you set t' end o' t' BT on a circle and mark t' appropriate lines. Ahoy! Arrr! I tend t' prefer t' wrap-around templates myself but this one was certainly serviceable. Begad! A door frame was then used t' extend t' lines. Well, blow me down! A tick mark was placed 1/4" from t' end on each o' t' fin lines and 3" from t' end on t' lug line. Begad! T' lines were then extended usin' a door frame.

This kit does nay provide precut balsa. Ahoy! You get a sheet o' stock material and a template you cut out and use t' mark out t' fins. Aye aye! Ahoy! T' lines were transferred t' t' balsa with a ballpoint pen and then t' fins were cut out usin' a steel ruler and razor knife.

Next comes some reinforcement o' t' forward end o' t' rocket. Some thin CA is wicked into t' first 1/4" or so o' t' BT. After it has cured, matey, it is sanded smooth. A 1/16" deep notch is then cut into t' end o' t' BT linin' up with one o' t' fin lines. Aye aye! T' purpose o' this notch is t' accommodate t' recovery system.

T' instructions go into exhaustive detail as t' t' best method o' streamlinin' t' fins into a teardrop shaped profile. Avast, arrr, me proud beauty! All well and good but its way over me interest level. Arrr! Begad! I settled for roundin' t' leading, outside, and trailin' edges.

T' instructions say t' install t' fins 1/4" forward o' t' aft end. Aye aye! Aye aye! They also say t' use CA. Ahoy! This made things almost too easy.

When t' CA had set, matey, I almost began t' fillet t' fins with yellow glue but I stopped and actually read t' instructions again. Filletin' does nay take place yet nor is glue recommended.

T' kit comes with a length o' Keelhaul®©™ thread. Ahoy! T' next step is t' cut off a 6" piece o' t' Keelhaul®©™ and set it aside for later. Well, blow me down! T' length that is left is tacked down with CA along t' root edge o' t' fin aligned with t' notch cut earlier. Ahoy! You need t' use a wire or somethin' similar t' hold t' Keelhaul®©™® straight and in place until t' CA sets up. Well, blow me down! Blimey! Blimey! Blimey! T' instructions recommend usin' an accelerant but I had none handy.

T' instructions call for t' filletin' t' be done with CA, matey, ya bilge rat, presumably thick CA. Begad! I be interested in givin' this a try but inspection revealed that all mine had hardened up due t' leavin' t' cap off. Blimey! T' instructions also make provisions for filletin' t' fins with yellow glue and I adopted this approach, goin' very slowly and buildin' t' fillets up over several layers.

One activity that could be completed while t' filletin' was goin' on was t' installation o' t' launch lug. It is mounted with its aft end 3" from t' bottom. Blimey! It was secured with CA by means o' slidin' t' lug onto an aluminum rod, ya bilge rat, applyin' t' CA t' t' lug and then pressin' t' rod and lug into place on t' marked line. Avast! T' rod be helpful in gettin' it t' line up straight. Blimey! It was withdrawn once t' CA set up.

T' nosecone is extremely thin and light vacuformed plastic. Avast! Blimey! Avast, me bucko, me proud beauty! Blimey! It comes in two pieces, shiver me timbers, t' ogive and t' base. Ya scallywag! Blimey! T' instructions say t' use a razor cutlass t' drill a small diameter hole in t' base, me bucko, matey, just big enough t' pass t' Keelhaul®©™® thread through. T' thread is then knotted. Avast, me proud beauty! I added a dab o' glue t' keep it from pullin' out.

T' two pieces o' t' NC are then fitted together and glued. I used liquid plastic cement very sparingly. Begad! I suspect it would be easy t' melt through t' plastic.

Finishing:
I sealed t' fins o' t' Hangtime with 3 coats o' sandin' sealer. Begad! I sanded betwixt t' 2nd and 3rd and after t' last coat.

I realize that many contest models are flown "naked" but I never liked t' looks o' unfinished rockets. Ahoy! Since I am nay a big competitor, I decided I wanted t' go ahead and give it a simple finish. Blimey! I wanted this t' get done with a single coatin' o' spray paint and no primer. Well, blow me down! Avast! In order t' cover up t' pencil marks, shiver me timbers, I chose black.

Before paintin' though, I used some maskin' tape t' cover up t' external Keelhaul®©™ shock cord. I then sprayed t' black.

Construction Rating: 4 out o' 5

Flight:
I got this rocket for a friendly competition in me local NARRRRR section. Arrr! T' event be t' be a B impulse streamer duration competition. Avast, me proud beauty! Well, blow me down! I wanted t' give it a whirl but did nay want t' work too hard at it. Avast! Aye aye! I figured t' go with a kit made for t' purpose.

It came with 2 tracin' paper streamers measurin' 6 x 60 inches along with instructions on how they should be pleated and prepped. Begad! It also came with a mylar sport streamer. Well, blow me down! Ahoy! I dutifully folded t' streamer and packed it usin' some tips from some real contest fliers. Blimey! For t' competition, shiver me timbers, me bucko, matey, I chose a B6-6. Blimey! I just knew I had a shot at this one.

There is no thrust ring. Ya scallywag! Blimey! Ahoy! Blimey! You just run tape around t' motor and t' BT and set it off.

5, shiver me timbers, 4, 3, ya bilge rat, 2, 1, matey, ignition. Begad! It took off up t' rod and a few feet later went squirrelly, loopin' all over t' sky but never very high. Avast! Aye aye! When it stopped thrusting, it plopped t' t' ground. Begad! A few seconds later came t' ejection pop. Aye aye! It blew t' NC but t' streamer stayed put.

Checkin' it out, t' streamer was nay in too tight. Begad! It pulled out easily.

Chan Stevens tells me that gettin' a Hangtime t' be unstable is quite an accomplishment. Later in t' afternoon, shiver me timbers, it passed a swin' test.

T' only damage be t' me pride and t' t' singed streamer. Avast! T' humiliation and pressin' RSO duties precluded another flight.

Recovery:
Gravity is very effective at returnin' this bird t' earth. Begad! I cannot say how well t' steamer works since mine never deployed.

Flight Rating: 2 out o' 5

Summary:
I think this one has potential but cannot swear by me one flight. Aye aye! Blimey! Ahoy! Blimey! Maybe I had a damaged motor. Blimey! Blimey! Well, blow me down! Blimey! Maybe t' rocket gods were angry with me. I dunno.

It is, shiver me timbers, however, fairly tough and has survived t' humiliate me another day.

Overall Rating: 3 out o' 5