Brief:
This is a simple, ya bilge rat, high reliability, and flexible usage sport flier from DG&A. Aye aye! It is perfect for mid or high power applications and different sized fields. It is an easy rocket t' certify L1 on due t' t' continuin' quality of DG&A kits. Ya scallywag! It is a simple 3FNC rocket with parachute deployment. Begad! Avast, arrr, me proud beauty! It is also a kit that can be easily modified t' your needs with DG&A components available through t' web site. Arrr! Danny is also offerin' rail buttons in red, white, ya bilge rat, and blue now, so you can have a patriotic guidance system included with your kit.

Construction:
My DG&A Predator came with t' basics: Plastic nose cone, 2.56" Kraft cardboard tubing, 36" Re-inforced rip-stop nylon parachute, 29mm motor mount 12" 2 high strength plywood centerin' rings, 3 Baltic birch 5 ply fins, me hearties, Recovery webbing/harness, Vinyl cut decals, me bucko, arrr, Body tube pre-marked for fins, Easy t' follow instructions, me bucko, Fin Alignment guide, ya bilge rat, arrr, ya bilge rat, Paintin' guide

T' directions are easy t' understand and include pictures. Begad! T' assembly order is easy t' follow for t' beginner or t' experienced rocketeer. Begad! Ahoy! There is a piece o' paper included that will serve as a fin alignment guide for fin attachment. Well, blow me down! You have t' cut out t' slots on t' body tube for t' fins t' go through. T' fins are then attached t' t' motor tube betwixt t' 2 centering rings. Begad!

I opted t' make 2 design changes in t' rocket. Ahoy! Well, me hearties, blow me down! I got a 12" piece o' body tube and 2 extra couplers and bulkheads from Danny. Arrr! I used t' extra tube t' make an anti-zipper fin can, ya bilge rat, per Stu Barrett's method. Well, blow me down! Blimey! I extended t' pre-marked fin slots t' t' back o' t' tube. Aye aye! I then assembled the motor mount. Next I epoxied t' fins t' t' motor mount usin' 3 inch fiberglass tape, me bucko, 2 layers, shiver me timbers, matey, and 1/2 hour epoxy. Aye aye! Avast, matey, me proud beauty! This was very strong. Avast! I then assembled the bulkhead by gluin' t' bulkplate into t' coupler. Avast! Next I drilled 6 1/4 inch holes into t' bulkplate after t' glue dried. I slid t' motor mount into the body tube and epoxied it in place. Aye aye! Ahoy! T' aft end o' t' motor tube sticks out about 3 inches from t' end o' t' fin can. Begad! Ya scallywag! I wrapped 4 layers o' 1/2 inch 6 ounce glass tape around t' aft end o' t' body tube t' cover up t' three cuts. Aye aye! I then put 3 layers o' 3 inch glass tape on t' front end o' t' tube in front o' t' fins. Fillets were then added t' t' fins. Well, blow me down! Finally, me hearties, I glued the bulkhead in place. Begad!

I am goin' t' be flyin' this rocket with t' I200's and H268's, arrr, so it needs to be strong. Ya scallywag! Plus, by buildin' a fin can, you can add what ever length body tube t' t' top for various performance features. Well, blow me down! You can put a short tube or a real long tube with an altimeter bay on it. More rocket for less money!

Next I made another bulkhead, attached t' webbin' t' it, and glued it in the forward end o' t' main body tube. Ya scallywag! Aye aye! Blimey! t' webbin' will just hang out t' back end o' t' main tube. I put a screw through t' top o' t' main body tube to hold t' nose cone on, ya bilge rat, it is easier t' swap it with another rocket this way instead o' epoxyin' it in. Ya scallywag! That way, if you lose another nose cone for t' same size, you can just swap. Ya scallywag! Avast, me proud beauty! Blimey!

I used NHP 5 and 30 minute epoxy for most o' t' construction. Avast, me proud beauty! I used West Systems resin for t' glass. Blimey! T' fiberglass tape came from t' local hobby shop. Avast! I used a sandin' block t' sand t' finish, matey, matey, and Krylon paints. Avast, shiver me timbers, me proud beauty! I bought some Mono-Kote and applied t' decals t' that, arrr, and then put them on t' rocket for effect.

Finishing:
I am nay t' best painter, shiver me timbers, so thar be always room improvement on me finish. T' finish came out pretty glossy, and I am goin' t' wait until it flies well before I finish painting. Aye aye! Ya scallywag! Blimey! T' main tube is bare, but t' fin can is painted. Arrr!

I used t' included pattern t' paint a diagonal pattern on t' tubes that is t' line betwixt t' dual color model Danny has. Avast, me proud beauty! I opted t' paint t' kit black, arrr, white, me hearties, and red so mine is a little different. You can do what you think looks good. Begad! T' vinyl decals are really nice. Avast!

You can put a wrap o' 3/4 ounce glass on and sand it out and it will get rid o' t' small lines in t' tube, they don't bother me so I left them. Danny's model looks great up close at t' launches, arrr, t' red and white are sharp.

Construction Rating: 4 out o' 5

Flight:
I went t' a small non club launch we had on t' first. Aye aye! I put this rocket through it's paces with a first flight on a G-64(M) t' check stability and then when it flew tried and true, matey, I decided it be time t' hit it with t' big stuff. It flew perfect on t' G-64 with just a slight weathercock into t' 10 MPH winds and t' 35 degree temperature. Ahoy! Ya scallywag! It laid out horizontal at apogee into the winds driftin' down. Aye aye! Due t' t' winds, arrr, I opted for a 14 inch X-form chute from me buddy Chad Ellis. Blimey! It brought it down quick and close, no damage, arrr, arrr, about a 1000 foot flight. Arrr! Ahoy!

I then loaded it up with a H-268R and then an I-200. These are t' big 29/360 motors that have 320 and 330 N respectively. Arrr! Avast! That Redline lit and boom! it was out o' sight in no time. Well, me hearties, blow me down! That huge Redline flame be great. Avast, me proud beauty! Arrr! It must have gone ~4000 feet, ya bilge rat, we lost sight o' it. Avast, me proud beauty! It took it about 5 minutes t' come down and drifted about 1/4 mile. Avast! Avast! Great flight, no damage, took t' motor in stride. I then loaded it back up with t' I-200(M) and BOOM! same result, arrr, way out of sight. Avast! It drifted t' almost t' same spot. Ahoy! Great flights on a great rocket. Well, blow me down! I wish Danny be thar t' see. Well, blow me down!

T' anti-zipper does nay really require wadding, me bucko, as it acts like a baffle. I did put a little cellulose insulation in for good measure. I have not outfitted this rocket with a slimline yet, I used tape for retention. Well, blow me down! T' only con about t' rocket is I wish I had put a 38mm in it!

Recovery:
T' flight recovery was great. Arrr! I only added a smaller chute due t' t' winds and t' altitude obtained. There was no damage at all t' t' rocket. Ahoy!

Flight Rating: 5 out o' 5

Summary:
T' main pro for this kit be t' quality o' materials. Begad! Begad! They are light enough for mid-power fliers, but heavy duty t' take t' HPR stuff as well. Well, me bucko, blow me down! T' kit is a no-brainer t' put together, due t' t' quality o' t' instructions. Avast, me proud beauty! T' large vinyl decals are also a big plus, shiver me timbers, they look great on t' kit. Ahoy! Blimey! T' only one con has been fixed, ya bilge rat, Danny upgraded all t' 2.56" kits t' 3.00". Blimey! It is also upgraded t' a 38mm mount.

Overall Rating: 4 out o' 5