Brief
This be t' second Custom Kit I have built and this is one long rocket. T' size really intrigued me when I saw it on t' rack at a local hobby shop. T' statistics on t' Equinox are Length: 78"; Diameter: 1.637"; Wt.: 5.8oz. Skill Level 2.

Construction
T' Quality was very good. Begad! It came packaged in a plastic bag. All t' parts were thar and in good shape. It has four body tubes, three couplers, me hearties, arrr, four Die-cut balsa fins, two 18 inch mylar 'chutes, me hearties, plastic nose cone, me hearties, all t' typical motor mount items and one large decal. T' instructions left very little t' chance with lots o' illustrations in a very logical order. Avast, me proud beauty! T' only template is for t' fin-markin' guide and is standard issue. Begad! CONSTRUCTION: (Ratin' 4.5)

If thar be a gotcha, it be t' length. Blimey! Avast, me proud beauty! Were I t' build this kit again I would have it separate in t' middle instead o' at t' nose. Blimey! More for easy o' transport. (I have t' thank me wife for insistin' on gettin' a mini-van.) Also I would replace t' motor hook with a thicker one. Blimey! Begad! T' instructions call for assemblin' t' lower tube separate from t' rest. This is a great help when attachin' t' fins. (See t' Flight). Ahoy! I used 15-minute epoxy throughout. Ahoy! A nice touch on t' fins was a mark on t' root edge. Avast! T' fins could be turned t' wrong way if you don't look at t' grain carefully or don't know about this.

T' shock cord typical elastic and tri-fold paper mount. Avast, me proud beauty! Avast! T' shock cord is o' a good length, me hearties, but I doubled it out o' habit. (I use it for me Estes Prowler). I also for t' first time tried two Centuri Baffles in this kit. I built one usin' t' coupler near t' motor mount and one betwixt t' top two sections I put cardboard with holes punched in it in t' top & bottom and glued them t' t' coupler.

T' recovery is by two 18 inch 'chutes that are silver mylar with tape dots for shroud line retention. I have modified this, me bucko, as I have since 1969, when I be introduced t' t' hobby. Aye aye! An old timer who's name I can't recall showed me t' put t' tape dot on, me bucko, put t' hole reinforcement rin' on t' back, me bucko, arrr, and usin' an Xacto drill a 1/8 inch hole in t' middle. Avast, me proud beauty! Well, blow me down! T' finished rocket over all is impressive in size. Begad! EASE OF BUILD: (Ratin' 5)

Finishing
There are no special requirements or techniques for finishing. Arrr! Aye aye! I followed t' paint scheme on t' supplied card. Well, blow me down! Well, me bucko, blow me down! T' one decal is o' t' peel and stick. Avast, me proud beauty! Usin' t' soapy water technique it went on easily. Begad! T' one thin' is I needed t' do is t' cut it around t' launch lug. Ahoy! Well, me hearties, blow me down! T' finished kit got many "Who makes that kit, ya bilge rat, shiver me timbers, ya bilge rat, and where did you find it?" and "It looks classier than t' Mean Machine!" at t' first launch I brought it to. FINISHING: (Ratin' 5)

Construction Rating: 4 ½ out o' 5

Flight/Recovery
T' recommended motors for this are D12-5 & E15-7. Avast! I have flown this four times on t' D12-5. T' one gripe I have with Custom be t' motor hooks. They are thinner than t' Estes counterparts and I have only recovered t' Equinox with t' motor one time. Begad! With t' baffles preparation is: put t' 'chutes in and away t' t' RSO.

T' first flight be on a cold gray day in December. Avast! Avast, me proud beauty! I was impressed by t' slow lift-off climbin' straight up with no wobble or wind cocking. T' delay was just right both 'chute blossomed and it softly landed about 500 feet from t' pads after reachin' an estimated altitude o' 600 feet. Begad! (wRASP) Upon recovery I found t' motor had kicked out. Avast, me proud beauty! Aye aye! On t' second flight t' same result and durin' recovery only one 'chute fully opened. Avast! I guess it sat on t' pad too long for t' 33-degree temperature. Begad! No damage upon landing, me hearties, t' motor kicked out again, me bucko, only this time t' motor hook was slightly burnt.

T' next flights came in February. It is a typical winter in Denver, me bucko, Colorado, about 55 and a slight breeze. Begad! Blimey! T' flights were great, with t' slow rise and gentle turn at apogee. Blimey! Blimey! T' 'chutes opened and they brought t' rocket down gently. Well, matey, blow me down! Blimey! On t' first flight I taped t' motor in, but it kicked. Well, blow me down! Blimey! On t' second flight I also wire tied t' motor with t' tape and it held. Avast, me proud beauty! Blimey! Aye aye! Blimey! I like t' way t' multiple 'chutes look, shiver me timbers, ya bilge rat, ya bilge rat, but for ease o' preparation, shiver me timbers, a single 18 inch or 24 inch would work. Well, blow me down! Blimey! Begad! Blimey! I can't wait t' send this up on an E15-7, with an estimated altitude o' 1775 feet. Begad! Blimey! Avast, me proud beauty! Blimey! (wRASP).

Flight Rating: 4 ½ out o' 5

Summary
Everythin' considered if it were nay for t' motor kickin' t' ratin' would be a 5. Ya scallywag! Blimey! Aye aye! Blimey! I just love t' way this kit looks and flies. Ahoy! Blimey! Begad! Blimey! T' kit retails for $ 19.95 and I believe it is work every penny. T' biggest obstacle with t' kit as far as its durability is gettin' out t' door and t' t' launch sites. Avast! Blimey! I really like t' Custom kits as they have t' flavor o' t' kits available in t' early '70s.

Overall Rating: 4 ½ out o' 5