Brief:
This is #8 o' 10 "ready t' build" models released by Semroc at NARAM-52. Begad! Blimey! Begad! Blimey! T' Mini Hustler is based upon t' Lee Piester/Centuri large scale series design but downscaled t' fly on 18mm motors. Blimey! Blimey! This could also be considered t' little brother o' Semroc's SLS Hustler and Lil' Hustler models.

Construction:
Parts were excellent quality, and t' sealed bag contained:

• Balsa nose cone
• Series 10 slotted body tube (1" ID)
• Series 13 payload bay (tube, balsa transition)
• Series 10 booster tube
• 18mm booster motor mount (tube, metal hook, matey, centerin' rings)
• TC-10 coupler
• Series 9 stuffer tube (1" OD)
• 18mm motor mount (tube, metal hook, centerin' rings)
• Laser-cut balsa fins (2 sets o' 4)
• Elastic shock cord
• 12" plastic chute
• Waterslide decals

T' "ready t' build" series is Semroc's answer t' numerous requests for "ready t' fly" rockets. Aye aye! In t' RTB series, shiver me timbers, t' modeler still has t' actually do work t' build and fly t' model, ya bilge rat, but t' design includes a number o' features that simplify t' build process, includin' slotted body tubes for thru-wall fin mounting, me bucko, me hearties, an alignment jig, and a stuffer tube t' serve as shock cord anchor and reinforce t' body tube.

T' RTB series are all fairly easy t' build, with almost all o' t' construction process usin' t' same standardized steps. This is definitely a skill level 1 model, me hearties, and aside from paint and surface prep, arrr, t' total build is well under an hour.

T' motor mount is a standard BT-20 tube, metal hook, ya bilge rat, me bucko, and a pair o' centerin' rings. Aye aye! Unlike t' typical mount, shiver me timbers, though, thar are two different centerin' rings involved with slightly different diameters. Pay careful attention t' t' instructions, as t' white rin' goes forward and t' brown rin' goes aft. Avast! Ya scallywag! This is critical later in t' process. Surprisingly, shiver me timbers, arrr, ya bilge rat, t' mount does nay include an inner motor block, so t' metal hook will have t' hold for t' life o' t' model. Blimey! I found t' centerin' rings a bit too snug, me hearties, me bucko, me bucko, and had t' peel off a layer o' paper from t' inside o' each, me bucko, ya bilge rat, plus one layer o' paper from t' outside o' t' white ring.

T' stuffer tube contains a couple slits, which are used t' slip t' elastic shock cord through, servin' as an anchor. After knottin' t' cord and reinforcin' with a drop o' glue, me bucko, it's ready for t' motor mount. Ahoy! Blimey! Avast! Blimey! T' motor mount slides just a tiny bit into t' stuffer tube, me bucko, ya bilge rat, arrr, enough that t' forward (white) centerin' rin' is flush with t' aft end o' t' stuffer tube. Do nay slide t' motor tube any further--the aft/brown rin' is too large for t' stuffer tube and instead is used t' align inside t' large series 10 body tube. Well, blow me down! Blimey! Well, blow me down! Blimey! Slidin' t' assembly into t' body tube t' dry fit is a good idea at this point, t' make sure t' forward centerin' rin' is aligned properly inside t' stuffer tube. Begad! Blimey! Well, blow me down! Blimey! Once t' motor mount/stuffer tube assembly has completely dried, arrr, it can then be glued inside t' body tube (though be careful t' make sure t' metal engine hook does nay line up under a fin slot).

Usin' t' same two-piece fin lock technology as t' larger Hustlers, these fins need t' be bonded together first, me bucko, me bucko, carefully linin' up t' matchin' groove patterns. Begad! Well, arrr, blow me down! As noted, me hearties, matey, fins are thru-wall, arrr, and t' fit against t' motor tube be very good. Begad! Included in t' kit is a nifty little cardboard fin alignment jog, matey, which fits smoothly on t' series 10 body tube and has notches t' accept 3 and 4 fin patterns. Avast, me proud beauty! T' fixture fits well for most fins in t' RTB series, though for fins that have a significant span and are nay swept back very far, ya bilge rat, t' slots in t' jig are nay long enough t' be o' much use. That wound up nay bein' an issue on this model.

T' payload bay is a simple extension, consistin' o' a 4.6" length o' body tube and a balsa transition, shiver me timbers, into which a screw eye anchor is inserted. Begad! I also drilled a couple vent holes in mine for altimeter use down t' road.

Tack on a pair o' launch lugs with standoffs , make t' chute and construction's done.

Finishing:
I went with t' stock paint scheme on this, matey, me hearties, startin' with two coats o' primer, arrr, followin' up with a couple thin coats o' gloss white, me bucko, then maskin' off t' hit t' fins, shiver me timbers, arrr, me hearties, transition and nose cone gloss black, arrr, and t' payload bay gloss red.

T' waterslide decals add t' name and a roll pattern.

Construction Rating: 4 out o' 5

Flight:
T' first flight on this turned out t' be a bit o' an adventure, more me fault than that o' t' model. Well, blow me down! Blimey! Avast, me proud beauty! Blimey! I loaded up a C6-5, matey, and has intended t' load an altimeter in t' payload bay, but wound up skippin' that due t' issues with t' battery holder on me altimeter. Avast, me proud beauty! Blimey! Well, blow me down! Blimey! As a result, t' nose cone was only secured with a light friction fit.

T' model flew perfectly straight off t' rod, shiver me timbers, and t' -5 be t' right delay, arrr, ya bilge rat, deployin' just over apogee. Begad! Blimey! Unfortunately, arrr, shiver me timbers, me hearties, t' elastic shock cord resulted in a snap-back effect on t' nose cone/payload, arrr, and t' nose cone picked up one o' those common smiles/dings when it struck t' body tube. Ahoy! Blimey! That was also enough force t' knock t' nose cone off t' bay. Avast! I was able t' track t' tumblin' cone along with t' rocket, so I manage a full recovery.

Recovery:
Other than t' nose cone issue, t' recovery was fine. Blimey! T' 12" chute is adequate for this weight.

Flight Rating: 4 out o' 5

Summary:
This Mini Hustler is a neat little payloader, and makes a nice addition t' t' Hustler family (SLS Hustler, matey, arrr, Lil' Hustler).

Overall Rating: 4 out o' 5