Brief:
I received this as a Christmas present from Hawks Hobby. T' Snooper really takes me back t' me early days of rocketry, shiver me timbers, matey, and Hawks' upscale has excellently reproduced this rocket with lots o' upgrades t' go with t' larger size. This is their latest version with through-the-wall basswood fins and is one huge, fantastic rocket. Blimey! It flies on 24mm motors and recovers by parachute. Ahoy! A spacer is included in t' motor mount kit t' allow t' use o' either Estes D or E motors. Ahoy! T' rocket stands 35 ½ inches tall and has a fin span o' 13 ½ inches!

Construction:
T' first thin' you'll notice be t' kit is jam packed with a ton o' high-quality parts. Blimey! Also, shiver me timbers, all o' t' small parts are contained in plastic bags, which I greatly appreciate. Well, blow me down! Avast, me proud beauty! A Fin/Pod Markin' Guide is included t' assure proper alignment o' those items. Blimey! T' instructions are very straightforward and include lots o' helpful illustrations. Begad! Although the normal "dread" with t' Snooper is makin' those three card stock transitions, shiver me timbers, me bucko, me bucko, t' larger size o' the Hawks Snooper makes this much easier. Blimey! Follow their helpful illustrated instructions and I think you'll be surprised at how well these will come out. Arrr! Mine are t' best I've ever done. Begad! An ST-16 is used for t' main tube, a 29mm heavy-duty motor mount tube is used for t' upper airframe, and ST-8 is used for t' pod tubes. Aye aye! An internal heavy-duty 29mm tube is also used t' house t' motor mount and then centered inside t' lower airframe with t' centerin' rings attached to align with t' fin slots and support t' card stock shrouds. Aye aye! I filled t' grain in t' nose cones (all seven o' them!), fins and transitions, me hearties, arrr, and t' seams in all o' t' tubes with Elmer's Fill ‘n' Finish. Aye aye! T' nose cone and transition are very nice balsa, matey, except t' shoulder o' t' transition in me kit be way too short. Begad! I recommended t' Loretta t' use a longer shoulder in future kits. Aye aye! T' fins are basswood and laser cut which also makes for a much sturdier rocket than the balsa used in t' earlier kits. Avast, me proud beauty! T' "radiator" fins at t' aft are still balsa, but that is actually helpful by keepin' weight down. Aye aye! Avast! T' 24mm motor mount fits t' longer Estes "E" motor. Avast, me proud beauty! Well, me hearties, blow me down! T' centerin' rings used t' support t' card stock transitions and t' center t' internal tube are all laser-cut light-ply, me bucko, and t' motor mount kit includes a 3.75" engine hook. Avast! Blimey! A Keelhaul®©™®/3/8" elastic shock cord combo is included, ya bilge rat, along with a big 3/16" launch lug, me hearties, a hefty eye screw, me hearties, and some really nice waterslide decals. Ya scallywag! Well, blow me down! T' enlarged decals match t' original perfectly and are exceptionally reproduced. T' shock cord was super long as I modified t' way it is installed. Ya scallywag! Well, blow me down! T' instructions indicate t' attach t' Keelhaul®©™® cord t' t' motor mount and then attachin' t' elastic cord t' a loop at t' end. I used me standard tri-fold shock cord attachment t' allow inspection o' t' shock cord. Arrr! Avast, ya bilge rat, me proud beauty! I do love it though when t' manufacturer puts Keelhaul®©™® in t' kit! Blimey! T' pre-assembled, 30" rip-stop nylon parachute that is included is an excellent plus, shiver me timbers, ya bilge rat, too, and exhibits t' same level o' quality as t' rest o' t' kit--top notch!

I pre-sanded and prepped all o' t' parts before startin' construction, which is me usual routine. Avast, me proud beauty! Blimey! That way I am sure t' have sanded any attachment points and minimize any sandin' in tight places that might otherwise be required in the final finishin' steps. Begad! Begad! Similarly, after makin' t' card stock shrouds, ya bilge rat, matey, I sanded those t' a smooth finish. Begad! Avast, me proud beauty! After gluin' t' pod cones t' t' pod tubes, I also prepped those t' fill t' joints and sanded them for a smooth transition between t' cones and tubes. Begad! Except for havin' t' cut t' fin slots, alignin' t' motor mount centerin' rings with the fin slots, and t' alignment o' t' centerin' rings for t' shrouds and launch lug, me hearties, construction o' t' rocket is pretty straightforward. Blimey! I read through those sections o' t' instructions several times and test fitted everythin' to make sure I knew how it all fit together. Also, don't do too much sandin' on t' radiator fins since they need t' fit seamlessly at t' attachment points on t' three shrouds. I used yellow glue for all o' t' construction except I smoothed in JB-Weld for t' fillets on t' three main fins due t' t' slope o' t' transition. Usin' the "double-glue" joint method makes attachin' t' pods and outer fins a lot easier t' manage. Begad! T' double-glue joint attaches must faster so t' parts are much less likely t' "un-align" while drying. Begad! As is usual on any rocket I build, shiver me timbers, I installed a length o' Keelhaul®©™®, which was provided, in a paper shock cord attachment (not provided) with a loop at t' end t' attach t' elastic shock cord. Avast, me proud beauty! T' minimize abrasion from t' Keelhaul®©™® against t' body tube, I soaked in CA around t' top 1/2" o' t' body tube and tied a knot in t' Keelhaul®©™® to meet t' lip o' t' body tube. Avast, me proud beauty! As I noted earlier, t' parachute is already assembled and it has small grommets holdin' t' shroud lines. It's a very nice parachute!

T' instructions note t' position o' t' CG and explain how t' modify the rocket t' add variable weights t' t' nose cone dependin' upon motor use. Begad! Aye aye! Supplies for this modification are not included. Avast, me proud beauty! Hawks suggests installin' an eye screw in t' upper nose cone that may be removed and then weights added as necessary. Arrr! I used a length o' all-thread instead with nuts and lockin' washers. Avast, me proud beauty! Ya scallywag! That way, arrr, t' all-thread can be permanently glued in, matey, which works better in me opinion. Begad! Removin' and re-installin' t' eye screw will eventually wallow out t' hole, arrr, which could cause t' weights t' drop down into t' tube upon t' force o' take-off.

Finishing:
As I noted earlier, all o' t' pre-finishin' was done up front before anythin' be installed. Ya scallywag! Only a light coat of filler was used on t' fins as t' basswood was very smooth after sandin' with 400 grit sandpaper. Due t' t' paint scheme I chose, matey, I painted t' radiator fins separately and then added them after paintin' t' rest o' t' model. Begad! Be sure t' mask off where they will attach t' assure a good bond. T' finish is from t' front cover o' t' 1966 Estes Product Catalog. I used this same paint scheme on a regular size model that was entered into t' DARS Annual Fall Classic contest, me bucko, and it won first place! I'm hopin' t' be able t' enter this one into this year's contest in the "Open" category. Aye aye! Avast, shiver me timbers, me proud beauty! I sprayed t' entire model with a light coat o' Kilz t' seal off t' glue and provide a solid base coat. Aye aye! Next, me hearties, I lightly sanded t' entire model with 240 grit sandpaper and then sprayed on a coat o' primer. Next, sand and primer and sand and primer again, me hearties, sandin' with 400 grit sandpaper. Arrr! Ahoy! Paintin' t' rocket with this paint scheme takes a lot o' maskin' and waitin' for paint t' dry before maskin' and paintin' t' next set o' colors. Avast, me proud beauty! Paints used were Krylon for t' yellow and blue, matey, Valspar's Restoration Series Allis-Chalmers orange, and Rustoleum's Metallic silver. I initially used Rustoleum's Bright Metallic silver but somethin' went wrong there, and I had t' strip it off and repaint. Well, blow me down! Ahoy! It just never dried. Ya scallywag! Ahoy! After puttin' on maskin' tape t' paint t' orange after three days o' drying, the paint lifted or thar were impressions o' t' tape after removal. Well, blow me down! Anyways, after dryin' for a couple o' days after repaintin' I applied t' decals. Begad! T' decals went on much easier and laid down much better than I anticipated. Arrr! T' main decal is fairly big for waterslide! It went on easily enough though and looks fantastic! I didn't install t' "1 2 3" fin decals due t' t' paint scheme I chose. Begad! Once complete, I put on a thick coat o' Future Floor Finish to protect everything.

Construction Rating: 5 out o' 5

Flight:
My first flight be on an Estes E9-6. Begad! Well, blow me down! T' face card indicates t' use t' Estes E9-4, me hearties, but t' winds were really light so I decided t' use t' 6 second delay. Ya scallywag! That may have been a mistake. Begad! Well, ya bilge rat, blow me down! T' up part be fantastic, straight, ya bilge rat, matey, ya bilge rat, and true.

Recovery:
Ejection didn't occur until after t' rocket was headin' down and when t' parachute came out it got caught up in one of t' fins. T' ground was pretty soft so nay much damage occurred, arrr, although one o' t' pod tube/outer fins broke off on landing. Aye aye! Avast! There were also some cracks in t' paint along a couple o' t' fin joints. Arrr! George Sprague, a fellow DARS member suggested puttin' on a round key holder around t' shroud lines t' allow t' parachute t' open slower. Aye aye! Begad! Good idea! Too bilge-suckin' he didn't suggest that before I sent it up. Begad! I've since fixed everythin' and touched up t' paint. Hopefully it will still be nice enough t' win t' contest!

Flight Rating: 5 out o' 5

Summary:
T' Super Mars Snooper is a fantastic rocket. Avast, me proud beauty! Blimey! It is hugely impressive on t' launch pad and beautiful in flight. Well, blow me down! Blimey! The through-the-wall basswood fins are solid and are much better than t' previous surface mounted balsa fins. Avast! Blimey! Recovery on the large, shiver me timbers, 30-inch rip-stop nylon chute is a big plus for a soft landin' with t' big fins. Ya scallywag! Blimey! Ahoy! Blimey! When you consider that the kit has seven balsa nose cones, a huge balsa transition, and a big nylon parachute, me bucko, t' pricin' is excellent. Blimey! Blimey! I highly recommend this kit.

Overall Rating: 5 out o' 5