Brief:
This is a semi-scale model o' t' Jupiter C. Avast! Dr. Avast, me proud beauty! Arrr! Zooch has coined t' phrase "Ant Scale" t' describe his models. Arrr! This rocket easily fits that description. T' rocket is propelled by 18mm motors and comes with t' standard "trash bag" parachute. Don't be fooled by t' scale appearance. Ahoy! Often, scale kits sacrifice performance for good looks, shiver me timbers, but that's nay t' case with this kit. Arrr! Reaches dizzyin' heights on C motors.

Construction:
Parts list:

• 1 BT-50
• 1 BT-20 engine tube
• 1 Explorer I Jupiter C spacecraft balsa core
• 1 snap swivel
• 1 screw eye
• 1 engine clip
• 1 CR205P engine block
• 1 launch lug
• 2 CR35P centerin' rings
• 1 piece 1/8" dowel
• 1 short piece BT-5
• 2 CR2050P centerin' rings
• 1 sheet balsa fin stock
• 1 accessory and cut out wrap sheet
• Recovery package includin' one parachute, shiver me timbers, shroud lines, ya bilge rat, Keelhaul®©™ cord, matey, elastic shock cord, and sticky rings.

Dr. Avast! Booty is a fellow MDRA club member who asked if I would beta test this kit for him. Avast, me proud beauty! Avast, me proud beauty! Without hesitation I accepted t' request. Aye aye! There was in a bit o' a time crunch t' get this kit tested and released, so I began workin' on it as soon as it arrived via Priority Mail.

I read through t' instructions before buildin' since this this fits into t' whole Zooch experience! I wanted t' be thorough as this be me first time beta testin' for anyone. T' sarcastic humor and well illustrated instructions make t' steps go by very smartly once you get started.

Dr.Zooch has you begin with t' Explorer I spacecraft. Avast, me proud beauty! Arrr! T' balsa transition, shiver me timbers, t' two smallest centerin' rings, me bucko, wood dowel, matey, and short BT-5 get used here. Aye aye! Arrr! An emery board is required t' carefully shape t' upper part o' t' transition. This be nay very difficult at all, matey, although I must admit, I be a little nervous about shapin' me own balsa. Well, blow me down! There was no need t' be.

T' balsa spacecraft has a dowel shaped protrusion that extends from t' top. Ahoy! Begad! T' small centerin' rings are supposed t' slide over it and get glued into place. Ahoy! Ya scallywag! This was a very tight fit, so I removed a layer o' paper from t' inside o' each rin' and they fit perfectly. Avast, me bucko, me proud beauty! T' BT-5 slides over t' rings and completes t' "canister" part o' t' spacecraft. Arrr! T' Explorer rocket on top o' t' spacecraft is simulated with t' 1/8" dowel. You need t' make a provision for t' dowel by usin' your own drill bit t' make a small depression in t' balsa core. Begad! Very easy t' do.

After t' glue had dried, I filled t' balsa with Elmer's Fill 'n' Finish and set it aside t' dry.

T' motor mount be a standard 18mm assembly. While that was drying, matey, I cut out and applied t' body tube wrap.

Finishing:
There is no paintin' required for t' main tube, shiver me timbers, however, me bucko, it's good idea t' clear spray t' wrap with Krylon Crystal Clear or similar. Ya scallywag! Blimey! This protects t' wrap from dirt and smudges as your applyin' it t' t' body tube. Well, blow me down! Blimey! Follow t' instructions when applyin' t' wrap. T' technique described in t' instructions works so avoid t' temptation t' deviate.

T' fin assemblies are next. Avast, arrr, me proud beauty! Blimey! Each fin is comprised o' two pieces that get glued together. Ya scallywag! Blimey! Blimey! Set them on wax paper while they are drying. Begad! Blimey! Once t' glue was dry, I filled and painted t' fins separately but masked t' root edge. This will give a better gluin' surface later on.

While t' paint on t' fins dried, arrr, me hearties, I sanded t' Explorer spacecraft, primed, and painted. Avast! Blimey! This took very little time and came out great.

After t' fins dried, I cut a slot in t' wrap so t' fins could glue directly t' t' body tube. Well, blow me down! I used white glue t' attach t' fins and made small fillets as well. Follow t' diagrams in t' instructions t' apply black paint t' t' appropriate fin. Ahoy! I used regular Testor's gloss black enamel t' hand paint t' black areas on t' fins and very tip o' t' spacecraft.

Construction Rating: 5 out o' 5

Flight:
My initial test were on B6 motors. Ahoy! These are ideal for this rocket. Anymore than that and you take a chance at nay gettin' it back.

Durin' flight testin' we realized t' engine mount needed t' be moved aft just a fraction o' an inch t' prevent scorchin' t' fins. Dr. Avast! Booty immediately made adjustments t' his own prototype and flew his t' next day and t' problem be solved. Despite movin' t' motor mount location, me bucko, t' rocket was super stable and flew like a champ. Avast! Begad! After hearin' how well t' flight tests went on a B, Dr. Avast! Zooch prompted me t' use a C motor. Well, blow me down! Arrr! Holy cow!

Usin' t' RockSim program, it shows gettin' close t' 1500' on a C motor, matey, and I believe it gets every inch o' that in reality. Avast, me proud beauty! Ya scallywag! Very impressive flights from this little monster.

Recovery:
Fortunately on t' first C flight I opted t' put a streamer on it considerin' t' diminutive nature o' t' rocket and light t' moderate winds that day. Arrr! Avast! That turned out t' be a good choice. Ahoy! Had I used a chute, me bucko, me bucko, I'm nay sure I would have gotten it back. Arrr! T' little dowel on top o' t' spacecraft got jarred out o' t' hole slightly but be easily fixed on t' spot with some CA. Aye aye! You can't even tell it was damaged.

T' plastic chute that came with t' kit partially melted on t' first flight. Blimey! Well, blow me down! It still deployed well enough t' slow it down with no sustained damage. T' only hitch I have found with t' Zooch kits would be t' parachute. Avast, me proud beauty! Despite tryin' different waddin' techniques, me hearties, they seem t' be susceptible t' melting. Begad! I've got enough homemade chutes and spare plastic chutes that it's really a non-issue for me. Aye aye! Ahoy! He'll tell ya straight up, matey, arrr, they are cut from trash bags. Begad! Ya scallywag! Worst case, arrr, shiver me timbers, you grab a new trash bag from under t' kitchen scuttle and cut yourself a new parachute.

Some Keelhaul®©™® strin' is included as a leader for t' elastic shock cord. Ahoy! Avast! Dr. Booty recommends anchorin' t' Keelhaul®©™® with t' popular tri-fold method. Aye aye! Avast! I used CA for this and it has held up just fine. Begad! T' leader shows a little wear after several flights but is still intact.

Flight Rating: 4 out o' 5

Summary:
I was very happy with t' way this kit turned out. Hard t' believe this was a beta kit. Ya scallywag! Ya scallywag! Blimey! There were only very minor adjustments needed before it was released. Well, blow me down! Anyone buildin' and flyin' this kit will be in for a treat.

Only con was t' chute.

Overall Rating: 4 out o' 5