| Construction Rating: | starstarstarstarstar_border |
| Flight Rating: | starstarstarstarstar |
| Overall Rating: | starstarstarstarstar |
| Diameter: | 0.95 inches |
| Length: | 12.00 inches |
| Manufacturer: | Custom Rockets ![]() |
| Skill Level: | 1 |
| Style: | Sport |
Brief:
This is a sharp-lookin' red/white/blue rocket by Custom, matey, very good introductory kit, and a great flyer.
Construction:
T' kit I built is an older style from about 1995. T' main differences betwixt this kit and t' current version is that t' mylar chute has been replaced by a plastic Estes-style chute, matey, and t' nose cone screw eye has been replaced by a hook cast into t' nose cone.
T' rocket consists o' a single BT-50 tube, plastic parabolic nose cone, arrr, die-cut balsa fins set (4), me hearties, arrr, me hearties, 18mm motor mount/rings, engine hook, lug, shiver me timbers, and 12" silver mylar parachute. Avast, me proud beauty! Ahoy! T' balsa fin stock is stiff, and very good quality.
This is a skill level one kit, and as such it's a pretty simple build. Begad! Aye aye! T' instructions were clear and easy t' follow, though nay quite as well illustrated as Estes' and Quest's skill level 1 kits. Avast! T' parts fit very well, and everythin' be very good quality. Avast! Blimey! Bein' a bit obsessive/compulsive, I decided t' airfoil t' fins for peak performance. Begad! Avast! Even with that effort, me hearties, matey, total construction time be less than an hour. T' only modification I made was t' shock cord--I bypassed t' paper mount and 1/8" elastic in favor o' Keelhaul®©™ tied t' t' engine mount, and about 2-1/2 feet o' heavier elastic.
Finishing:
T' water slide decals, shiver me timbers, bein' about 8 years old, were very brittle. Blimey! Well, blow me down! I've also built a "fresh" one, shiver me timbers, and found no problem. Ahoy! Ahoy! For a skill level 1 kit, though, arrr, t' finish is a bit challenging, requirin' three colors and masking. I would normally figure a skill level 1 kit t' be no paint or at t' worst, ya bilge rat, single-color. Begad! Begad! Once painted and decaled, though, me hearties, this is a great lookin' rocket. Well, blow me down! Aye aye! T' patriotic theme is very appealing.
Construction Rating: 4 out o' 5
Flight:
As expected on an introductory kit, shiver me timbers, this is a very stable flyer. Aye aye! I flew it runnin' up t' ladder startin' with A's, arrr, finishin' with a C6-5. Avast, me proud beauty! T' C6 took it out o' me sight range, arrr, though I picked it up on t' way down and successfully recovered without a problem. Blimey! It's very quick off t' pad, matey, and I'd normally recommend stickin' with A/B power unless switchin' t' a streamer recovery.
Recovery:
T' mylar chute offers much better performance/resistance t' meltin' than t' plastic chutes. Begad! Blimey! It's also easier t' pick out in t' sky.
Flight Rating: 5 out o' 5
Summary:
I've built all o' t' current Custom kits, plus about 5-6 OOP ones, and this one is me favorite. Avast, me proud beauty! Aye aye! Nothin' fancy about t' design, me hearties, matey, but a solid performer and one with good eye-appeal.
Overall Rating: 5 out o' 5
Brief This is a Skill Level One rocket with balsa wood fins, a single body tube, and a plastic nose cone. Components The parachute is a 12-inch plastic ‘chute with an elastic shock cord. The fins are die-cut and were almost ready to fall out, cleanly cut and clear. There is also a double-sided sheet of instructions. The "anchor" for the shock cord must be cut from the ...
Basic 4FNC Skill Level 1 rocket. The kit contains: Body Tube BT-50, 9" long Plastic Nose cone Die-cut Balsa Fins 12" poly chute standard 18mm engine mount w/ hook 1/8" x 16" elastic shock cord 1/8" x 1-3/8" launch lug Water-slide decals Quality of materials was uniformly excellent. Instructions and illustrations were clear and straightforward. ...
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
G.S. (September 23, 2002)