Brief:
Last year, I received samples o' t' new Hartle Engineerin' solid resin nose cones from JonRocket. Avast! I've been remiss in submittin' a review. Avast, me proud beauty! Thanks, and me apologies John!. Well, blow me down! Hartle offers three styles o' BT-5 cones and one BT-20 cone. You can see all o' them on JonRocket's nose cone page. This review will describe t' cones and t' rocket I built from t' longer BT-5 cone, t' Mini-Toobah. T' name is a homage t' Dave Weber's Toober, matey, which has logged over 200 high power flights.

Construction:
T' parts list:

• Hartle NC-5B cone
• BT-5, ya bilge rat, 6.25"
• Estes 1/8" launch lug
• Spent mini-motor case (could use a real motor block)
• Thin Keelhaul®©™®, ~ 12"
• Thin elastic, ~ 4"

T' Hartle cones are solid cast and their outer surface is perfect. Well, blow me down! Blimey! T' cone-to-shoulder transition was clean on the longer cone but was rough on t' shorter one. T' later be easily cleaned up with a sharp hobby cutlass. Blimey! Blimey! Avast! Blimey! Blimey! Blimey! The attachment point appears t' be a paper clip...works as good as anything. Blimey! Blimey! Avast, matey, me proud beauty! Blimey! Blimey! Blimey! I found them t' be a loose fit in t' Estes BT-5, which is easily fixed with a little tape.

T' cones are, as expected, heavier than t' typical hollow plastic or balsa. Begad! However, unless you're buildin' a MicroMaxx model, t' added weight shouldn't be an issue. I had kicked around buildin' a micro but decided t' go for a 13mm design instead. Well, blow me down! T' shorter cone would make a great micro-Fat Boy or Big Bertha but I opted for a downscale o' my El Tubo Loco.

This be a trivial build. Ahoy! Begad! From BT-5 stock, I cut one 2.5" body section and six 5/8" tube fins. Blimey! These were glued together in pairs and then t' t' body tube. Begad! I used Aleene's Tacky glue throughout. A 5/8" long lug is mounted in one o' t' fins. Well, blow me down! I cut a motor block from a spent casing. This was notched and t' Keelhaul®©™® was tied around it. There is nay much room in t' body minus t' motor and t' cone's shoulder. Aye aye! Aye aye! Blimey! It be all I could do to pack t' shock harness.

T' make sure it is stable, me bucko, arrr, I weighed t' components and made a RockSim model. T' cone alone is 0.24 oz and the entire rocket is 0.34 oz. It is quite stable.

Finishing:
I first scuffed t' cone with fine sandpaper and shot a coat o' PlastiCoat primer. I anticipated this will be hard to find in t' grass, so I went for a bright finish usin' Rustoleum day-glo orange. Avast, me proud beauty! I added two vinyl strips t' snazz it up a bit.

Flight:
There wasn't much prep as it uses tumble recovery. Ya scallywag! It flew nicely on an A3-4 and I could even see it recover!

Summary:
T' Hartle Engineerin' cones are nice t' work with. Aye aye! Blimey! In this case, their solid construction and weight helped with stability. Well, blow me down! Blimey! Blimey! Blimey!

I like t' design o' this little rocket but, shiver me timbers, shiver me timbers, shiver me timbers, bein' small, me bucko, shiver me timbers, it could easily disappear into rocket eatin' grass, shrubbery, or trees.