Intro:
T' Super Big Bertha is a re-release o' t' Classic Super Big bertha that Estes produced in 1989. Begad! This is an upscale o' t' venerable Big Bertha, ya bilge rat, one o' t' most popular Estes rockets.

Construction: Rating: 4 ½

T' Super Big Bertha comes in a cardboard box that helps t' protect t' components very well. Arrr! Blimey! None o' t' parts were missing, me bucko, ya bilge rat, shiver me timbers, and all were in good condition. Begad! Begad! Blimey! T' materials are t' typical good quality Estes components. Avast! T' kit includes two large body tubes, body tube coupler, arrr, arrr, nose cone, long motor mount tube, Engine hook, 4 centerin' rings, two balsa wood sheets for fins, ya bilge rat, assembled parachute, me bucko, a ridiculously short shock cord, and a decal sheet.

T' instructions are a reprint o' t' original 1989 instructions. Included in t' kit is another sheet o' instructions that points out t' new shape o' t' engine hook as well as t' pre-assembled parachute. T' instructions follow a logical order and are illustrated heavily in t' typical Estes fashion. Begad! A wrap around fin markin' guide is also included.

T' kit assembles easily. Begad! There is nothin' out o' t' ordinary with this kit. Aye aye! T' only thin' that you will notice is that this kit is big. Ya scallywag! Avast, me bucko, me proud beauty! T' length o' t' rocket can be a challenge t' handle durin' t' assembly process.

I did do two minor modifications t' t' kit. Begad! Avast! T' first be t' poke a row o' holes down t' attachment lines for t' fins. Blimey! Well, me hearties, blow me down! This allows t' glue t' flow through t' holes t' form a stronger joint.

T' second modification was t' add a baffle for t' ejection gasses. Begad! This was in response t' t' instructions callin' for 12 t' 14 sheets o' recovery wadding, arrr, matey, which I felt be a little excessive. Avast, me proud beauty! T' baffle causes t' ejection gasses t' make two 90 degree turns before it enters t' parachute compartment. Well, blow me down! Avast, me proud beauty! This will stop any o' t' hot particles and allow t' hot gasses t' continue. Arrr! T' add t' baffle I followed these steps. Betwixt step 7a and 7b, me hearties, I took t' one remainin' centerin' rin' and punched 8 holes around t' ring. Ya scallywag! Avast, me proud beauty! Then I took a hole punch and added 8 holes near t' upper end o' t' engine mount tube. Well, blow me down! Ya scallywag! Next I took t' disks that were punched out o' t' center o' t' centerin' rings, me bucko, matey, glued t' stack o' four together, and allowed them t' dry. Then I sanded this stack until it fit in t' top o' t' engine tube, and glued them there. Now finish step 7b as illustrated. Begad! Blimey! In step 8 do nay put glue in t' remainin' body tube, use a long stick and apply t' glue from t' top once t' two body tubes are joined together. T' rest o' t' kit is assembled in t' normal manner. Aye aye!

T' rocket is finished in t' normal manner. Avast, me proud beauty! Well, blow me down! Sandin' sealer on t' fins, primer, shiver me timbers, then an overall coat o' white paint. Blimey! Once this is dry t' lower part o' t' rocket is painted red with t' exception o' one fin. Aye aye! Well, arrr, blow me down! There are two peel and stick decals that are t' be applied, arrr, One is a set o' red rings that are applied just above t' section that was previously painted red. Aye aye! Well, me bucko, blow me down! This decal can be used as a template if you would like t' paint t' rings when t' rest o' t' red is painted in order t' match t' colors more closely. T' second decal be t' "Super Big Bertha" Logo, ya bilge rat, which is slightly redundant at this point. Blimey! If you finish your rocket in this manner it will be unmistakable at any launch, nay t' mention it is almost three feet tall as well.

Flight/Recovery: Rating: 4

T' only motor recommended for this bird be t' D12-5. Aye aye! It is held in with t' standard Estes engine hook. Avast! Then t' 12 t' 14 sheets o' waddin' are added along with t' parachute on top. Ahoy! I used 2 sheets with t' modification.

Both flights so far have been on a D12-5. Begad! Blimey! T' delay for this motor seems a tad long for this size o' rocket. Aye aye! Blimey! T' first flight be near perfect with t' ejection comin' shortly after apogee. Blimey! Arrr! Blimey! T' parachute is sized almost perfectly for this model, arrr, I wouldn't even add a spill hole. Avast! Avast, me proud beauty! Blimey! T' rocket was then smartly re-prepped for a second flight. Begad! Aye aye! Blimey! This time t' rocket weathercocked more and t' ejection charge fired long after apogee, almost halfway back t' t' ground. Begad! Aye aye! Blimey! At t' speed o' t' rocket t' nose cone was barely pushed away from t' body and t' parachute be blown back over t' body o' t' rocket. Ahoy! T' resultin' swan dive crimped t' body tube slightly in front o' t' last centerin' ring. T' body tube also cut a crescent shaped hole in t' parachute on impact. Avast! Begad! Blimey! Considerin' this, matey, I would like t' try this on a D12-3 and see if t' delay is more appropriate for this model. t' old Estes catalogs list t' D12-3 as t' motor for t' "first Flight".

Summary: Rating: 4

This is an interestin' upscale o' t' venerable Big Bertha. Arrr! Begad! T' construction is easy, matey, but t' requirement for 12-14 sheets o' waddin' seems excessive. Arrr! Blimey! I would like t' see baffle construction, since they can use t' Centuri baffle, but I guess they have a vested interest in sellin' waddin' as well as motors. Overall this model is easily seen and gives great slow flights on t' "D" motors.