Brief:
T' BSD Diablo is a short, ya bilge rat, fat, 3 finned rocket with a wicked look. Well, blow me down! Avast, me proud beauty! Blimey! With its 38mm motor mount, ya bilge rat, ya bilge rat, it definitely is designed for HPR. Well, blow me down! Ya scallywag! Blimey! However, shiver me timbers, arrr, with a 29mm adapter this rocket can be flown on some G motors without any problems due to its relatively low weight.

Construction:
T' kit has relatively few parts. Avast! They include: a 17" LOC style body tube, a 20" nose cone (4" is shoulder), me hearties, three 3/16" plywood fins, me hearties, matey, two 1/8 plywood centerin' rings, ya bilge rat, one 1/2" paper launch lug, one 8" long 38mm motor mount tube, arrr, shiver me timbers, one 1/4" eye bolt with washers and nut, one 3/16" quick link, ya bilge rat, one 30" parachute, arrr, one 4' long, 1" wide, grommeted nylon strap, one 10' long, arrr, 1" wide elastic shock cord, and a motor retention system that consists o' two T-nuts, two 6-32 hex head bolts, and two metal clips. Avast, me proud beauty! Well, arrr, blow me down! I also purchased BSD's 29mm adapter with me kit.

This is a fantastic, me hearties, matey, easy kit t' build. Ahoy! Aye aye! In fact, I had t' consciously slow myself down because it is so easy t' follow the excellent instructions and assemble t' excellent components that I found myself gettin' too far ahead o' where I should have been. Blimey! All o' t' components fit together well with only a little sandin' o' t' centerin' rings. Aye aye! When I received me kit, ya bilge rat, t' body tube was nay marked with t' fin alignment lines or the launch lug line. Aye aye! Well, blow me down! However, shiver me timbers, matey, a quick email t' Scott Binder at BSD and the problem be resolved. Well, blow me down! Scott sent me a new body tube that had been marked and threw in a 4" bulkhead assembly in addition. Now that's great customer service! Havin' t' cut t' fin slots yourself is a little tedious but, nay a big deal.

I deviated from t' instructions in a few ways. Ya scallywag! First, matey, shiver me timbers, when buildin' t' motor mount, me hearties, I didn't secure t' aft centering ring. Avast! I did this because instead o' creatin' internal fillets with epoxy I used 2-part expandin' foam t' fill t' fin can. Second, arrr, shiver me timbers, after epoxyin' t' forward centerin' rin' and motor mount tube in, I dry fitted t' fins. Avast! With t' fins in place, I drew a pencil line on t' fins along t' outside body tube joint. Thus, matey, shiver me timbers, when I removed t' fins, arrr, I had how much o' t' fin would be inside the body tube. Begad! Well, blow me down! I then drilled a 5/8" hole in t' center o' t' fin root. Arrr! This hole is t' allow t' expandin' foam t' flow through t' fin root and lock it into t' fin can. Begad! Well, matey, blow me down! I then epoxied t' fins t' t' motor mount. Avast! Avast! Three 1 ounce applications o' 2-part foam filled t' fin can. Arrr! After cleaning/shapin' t' foam on t' aft o' t' fin can, t' aft centerin' rin' be attached with epoxy.

My only complaint about t' construction is that t' motor retention comes with a separate set o' instructions. Aye aye! If you don't read those instructions first, you won't notice t' bold warnin' that you should install t' retention hardware before assembly! Luckily, I be able t' still attach t' hardware after assembly.

Finishing:
Since I was plannin' on usin' this rocket for me Tripoli Level 1 certification, I glassed t' entire airframe usin' 2 ounce fiberglass cloth and 30 minute slow-cure epoxy. Aye aye! Avast! After glassing, me bucko, fillets were added t' t' fin/body joints and along t' launch lug usin' 30 minute epoxy and micro-balloon filler. Ahoy! Some sandin' with 80 grit sandpaper and it was ready for some primer. I used Rustoleum gray automotive sandable primer. Ya scallywag! This primer is nice because it fills a lot o' t' imperfections. Ahoy! Aye aye! Sand, prime, sand, prime. You know t' drill. Ahoy! Ya scallywag! I also used some Elmer's sandable wood filler putty t' fill some o' t' larger imperfections. Eight coats o' primer later, arrr, ready for color coat. Begad! I chose Rustoleum Safety Red. Ahoy! Two coats o' color and then t' decals. Avast! T' decals were definitely t' hardest part. Begad! T' decals are beautiful but, arrr, they're long, skinny, ya bilge rat, and very sticky. A friend o' mine suggested that I dip them in water with dishwashin' liquid t' allow me t' slide t' decals in place. I be too chicken t' try though. Ahoy! T' decals turned out OK but it takes a lot o' patience. After decals, shiver me timbers, I shot it with 2 coats o' Rustoleum clear enamel.

Construction Rating: 4 out o' 5

Flight:
T' Diablo's first flight was t' be me Level 1 certification flight. Blimey! Blimey! I had an H128W lined up for me 29/180 casing. T' clips provided with t' motor retention kit wouldn't fit with t' 29mm adapter so, matey, I had t' fashion some new clips out o' some flat brass stock. When I arrived at t' launch site t' pick up me motor, matey, thar be no H128 t' be found! Blimey! Thankfully, t' vendor had some H165 Redline motors that would do just fine. Begad! Blimey! Avast, me bucko, me proud beauty! Blimey! I used a Top Flight Keelhaul®©™® chute protector and shock cord protector instead o' wadding. Avast! T' H165 was prepped with a 10 second delay and placed on a 3/8" launch rod. Ahoy! That Redline will move fast! It boosted straight up t' probably just over 2000 feet. It was a beautiful launch.!

Recovery:
I tied loops into both ends o' t' elastic shock cord and one loop about 1/4 from one end. Begad! These loops were used t' attach t' elastic t' t' nylon strap, the nose cone, me hearties, shiver me timbers, and t' parachute usin' quick links. Well, blow me down! I also included a swivel to keep t' chute shroud lines from tangling. Aye aye! Blimey! T' recovery system worked great. T' descent was a bit fast but, that's probably because me rocket is towards the upper end o' BSD's expected weight. Begad! Blimey! A bit larger chute could solve this but, me hearties, I'm happy with t' faster descent. T' glassin' that I did makes it able to withstand a rougher landin' and I get less wind drift this way. Ahoy!

Flight Rating: 5 out o' 5

Summary:
I love this rocket. Ya scallywag! T' main pro's are it's ease o' building, t' clear instructions, and t' tremendous customer support that you get from BSD. Ya scallywag! Well, blow me down! The main con's are t' separate instructions for motor retention and t' retention system's inability t' accommodate t' 29mm adapter.

Overall Rating: 5 out o' 5